[PATCH v2 15/15] mtd: nand: hynix: add read-retry support for 1x nm MLC NANDs
Boris Brezillon
boris.brezillon at free-electrons.com
Wed Jun 8 06:00:49 PDT 2016
All Hynix MLC NANDs using the produced with the 1X nm process support
read-retry.
This read retry implementation should also be reusable for other Hynix
NANDs, but the method to retrieve the read-retry parameters from the
read-retry OTP area might change a bit (some NANDs are even using a fixed
set of values instead of retrieving those information from the OTP area).
Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
---
drivers/mtd/nand/nand_hynix.c | 361 +++++++++++++++++++++++++++++++++++++++++-
1 file changed, 360 insertions(+), 1 deletion(-)
diff --git a/drivers/mtd/nand/nand_hynix.c b/drivers/mtd/nand/nand_hynix.c
index f73b99f..7f5b446 100644
--- a/drivers/mtd/nand/nand_hynix.c
+++ b/drivers/mtd/nand/nand_hynix.c
@@ -13,6 +13,53 @@
*/
#include <linux/mtd/nand.h>
+#include <linux/slab.h>
+
+#define NAND_HYNIX_CMD_SET_PARAMS 0x36
+#define NAND_HYNIX_CMD_APPLY_PARAMS 0x16
+
+#define NAND_HYNIX_1XNM_RR_REPEAT 8
+
+/**
+ * struct hynix_read_retry - read-retry data
+ * @nregs: number of register to set when applying a new read-retry mode
+ * @regs: register offsets (NAND chip dependent)
+ * @values: array of values to set in registers. The array size is equal to
+ * (nregs * nmodes)
+ */
+struct hynix_read_retry {
+ int nregs;
+ const u8 *regs;
+ u8 values[0];
+};
+
+/**
+ * struct hynix_nand - private Hynix NAND struct
+ * @nand_technology: manufacturing process expressed in picometer
+ * @read_retry: read-retry information
+ */
+struct hynix_nand {
+ const struct hynix_read_retry *read_retry;
+};
+
+/**
+ * struct hynix_read_retry_otp - structure describing how the read-retry OTP
+ * area
+ * @nregs: number of hynix private registers to set before reading the reading
+ * the OTP area
+ * @regs: registers that should be configured
+ * @values: values that should be set in regs
+ * @page: the address to pass to the READ_PAGE command. Depends on the NAND
+ * chip
+ * @size: size of the read-retry OTP section
+ */
+struct hynix_read_retry_otp {
+ int nregs;
+ const u8 *regs;
+ const u8 *values;
+ int page;
+ int size;
+};
static bool hynix_nand_has_valid_jedecid(struct nand_chip *chip)
{
@@ -27,6 +74,292 @@ static bool hynix_nand_has_valid_jedecid(struct nand_chip *chip)
return !strcmp("JEDEC", jedecid);
}
+static int hynix_nand_setup_read_retry(struct mtd_info *mtd, int retry_mode)
+{
+ struct nand_chip *chip = mtd_to_nand(mtd);
+ struct hynix_nand *hynix = nand_get_manufacturer_data(chip);
+ const u8 *values;
+ int status;
+ int i;
+
+ values = hynix->read_retry->values +
+ (retry_mode * hynix->read_retry->nregs);
+
+ /* Enter 'Set Hynix Parameters' mode */
+ chip->cmdfunc(mtd, NAND_HYNIX_CMD_SET_PARAMS, -1, -1);
+
+ /*
+ * Configure the NAND in the requested read-retry mode.
+ * This is done by setting pre-defined values in internal NAND
+ * registers.
+ *
+ * The set of registers is NAND specific, and the values are either
+ * predefined or extracted from an OTP area on the NAND (values are
+ * probably tweaked at production in this case).
+ */
+ for (i = 0; i < hynix->read_retry->nregs; i++) {
+ int column = hynix->read_retry->regs[i];
+
+ column |= column << 8;
+ chip->cmdfunc(mtd, NAND_CMD_NONE, column, -1);
+ chip->write_byte(mtd, values[i]);
+ }
+
+ /* Apply the new settings. */
+ chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1);
+
+ status = chip->waitfunc(mtd, chip);
+ if (status & NAND_STATUS_FAIL)
+ return -EIO;
+
+ return 0;
+}
+
+/**
+ * hynix_get_majority - get the value that is occurring the most in a given
+ * set of values
+ * @in: the array of values to test
+ * @repeat: the size of the in array
+ * @out: pointer used to store the output value
+ *
+ * This function implements the 'majority check' logic that is supposed to
+ * overcome the unreliability of MLC NANDs when reading the OTP area storing
+ * the read-retry parameters.
+ *
+ * It's based on a pretty simple assumption: if we repeat the same value
+ * several times and then take the one that is occurring the most, we should
+ * find the correct value.
+ * Let's hope this dummy algorithm prevents us from losing the read-retry
+ * parameters.
+ */
+static int hynix_get_majority(const u8 *in, int repeat, u8 *out)
+{
+ int i, j, half = repeat / 2;
+
+ /*
+ * We only test the first half of the in array because we must ensure
+ * that the value is at least occurring repeat / 2 times.
+ *
+ * This loop is suboptimal since we may count the occurrences of the
+ * same value several time, but we are doing that on small sets, which
+ * makes it acceptable.
+ */
+ for (i = 0; i < half; i++) {
+ int cnt = 0;
+ u8 val = in[i];
+
+ /* Count all values that are matching the one at index i. */
+ for (j = i + 1; j < repeat; j++) {
+ if (in[j] == val)
+ cnt++;
+ }
+
+ /* We found a value occurring more than repeat / 2. */
+ if (cnt > half) {
+ *out = val;
+ return 0;
+ }
+ }
+
+ return -EIO;
+}
+
+static int hynix_read_rr_otp(struct nand_chip *chip,
+ const struct hynix_read_retry_otp *info,
+ void *buf)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+ int i;
+
+ chip->select_chip(mtd, 0);
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+
+ chip->cmdfunc(mtd, NAND_HYNIX_CMD_SET_PARAMS, -1, -1);
+
+ for (i = 0; i < info->nregs; i++) {
+ int column = info->regs[i];
+
+ column |= column << 8;
+ chip->cmdfunc(mtd, NAND_CMD_NONE, column, -1);
+ chip->write_byte(mtd, info->values[i]);
+ }
+
+ chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1);
+
+ /* Sequence to enter OTP mode? */
+ chip->cmdfunc(mtd, 0x17, -1, -1);
+ chip->cmdfunc(mtd, 0x04, -1, -1);
+ chip->cmdfunc(mtd, 0x19, -1, -1);
+
+ /* Now read the page */
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, info->page);
+ chip->read_buf(mtd, buf, info->size);
+
+ /* Put everything back to normal */
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ chip->cmdfunc(mtd, NAND_HYNIX_CMD_SET_PARAMS, 0x38, -1);
+ chip->write_byte(mtd, 0x0);
+ chip->cmdfunc(mtd, NAND_HYNIX_CMD_APPLY_PARAMS, -1, -1);
+ chip->cmdfunc(mtd, NAND_CMD_READ0, 0x0, -1);
+ chip->select_chip(mtd, -1);
+
+ return 0;
+}
+
+#define NAND_HYNIX_1XNM_RR_COUNT_OFFS 0
+#define NAND_HYNIX_1XNM_RR_REG_COUNT_OFFS 8
+#define NAND_HYNIX_1XNM_RR_SET_OFFS(x, setsize, inv) \
+ (16 + ((((x) * 2) + ((inv) ? 1 : 0)) * (setsize)))
+
+static int hynix_mlc_1xnm_rr_value(const u8 *buf, int nmodes, int nregs,
+ int mode, int reg, bool inv, u8 *val)
+{
+ u8 tmp[NAND_HYNIX_1XNM_RR_REPEAT];
+ int val_offs = (mode * nregs) + reg;
+ int set_size = nmodes * nregs;
+ int i, ret;
+
+ for (i = 0; i < NAND_HYNIX_1XNM_RR_REPEAT; i++) {
+ int set_offs = NAND_HYNIX_1XNM_RR_SET_OFFS(i, set_size, inv);
+
+ tmp[i] = buf[val_offs + set_offs];
+ }
+
+
+ ret = hynix_get_majority(tmp, NAND_HYNIX_1XNM_RR_REPEAT, val);
+ if (ret)
+ return ret;
+
+ if (inv)
+ *val = ~*val;
+
+ return 0;
+}
+
+static u8 hynix_1xnm_mlc_read_retry_regs[] = {
+ 0xcc, 0xbf, 0xaa, 0xab, 0xcd, 0xad, 0xae, 0xaf
+};
+
+static int hynix_mlc_1xnm_rr_init(struct nand_chip *chip,
+ const struct hynix_read_retry_otp *info)
+{
+ struct hynix_nand *hynix = nand_get_manufacturer_data(chip);
+ struct hynix_read_retry *rr = NULL;
+ int ret, i, j;
+ u8 nregs, nmodes;
+ u8 *buf;
+
+ buf = kmalloc(info->size, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ ret = hynix_read_rr_otp(chip, info, buf);
+ if (ret)
+ goto out;
+
+ ret = hynix_get_majority(buf, NAND_HYNIX_1XNM_RR_REPEAT,
+ &nmodes);
+ if (ret)
+ goto out;
+
+ ret = hynix_get_majority(buf + NAND_HYNIX_1XNM_RR_REPEAT,
+ NAND_HYNIX_1XNM_RR_REPEAT,
+ &nregs);
+ if (ret)
+ goto out;
+
+ rr = kzalloc(sizeof(*rr) + (nregs * nmodes), GFP_KERNEL);
+ if (!rr)
+ goto out;
+
+ for (i = 0; i < nmodes; i++) {
+ for (j = 0; j < nregs; j++) {
+ u8 *val = rr->values + (i * nregs);
+
+ ret = hynix_mlc_1xnm_rr_value(buf, nmodes, nregs, i, j,
+ false, val);
+ if (!ret)
+ continue;
+
+ ret = hynix_mlc_1xnm_rr_value(buf, nmodes, nregs, i, j,
+ true, val);
+ if (ret)
+ goto out;
+ }
+ }
+
+ rr->nregs = nregs;
+ rr->regs = hynix_1xnm_mlc_read_retry_regs;
+ hynix->read_retry = rr;
+ chip->setup_read_retry = hynix_nand_setup_read_retry;
+ chip->read_retries = nmodes;
+
+out:
+ kfree(buf);
+
+ if (ret)
+ kfree(rr);
+
+ return ret;
+}
+
+static const u8 hynix_mlc_1xnm_rr_otp_regs[] = { 0x38 };
+static const u8 hynix_mlc_1xnm_rr_otp_values[] = { 0x52 };
+
+static const struct hynix_read_retry_otp hynix_mlc_1xnm_rr_otps[] = {
+ {
+ .nregs = ARRAY_SIZE(hynix_mlc_1xnm_rr_otp_regs),
+ .regs = hynix_mlc_1xnm_rr_otp_regs,
+ .values = hynix_mlc_1xnm_rr_otp_values,
+ .page = 0x21f,
+ .size = 784
+ },
+ {
+ .nregs = ARRAY_SIZE(hynix_mlc_1xnm_rr_otp_regs),
+ .regs = hynix_mlc_1xnm_rr_otp_regs,
+ .values = hynix_mlc_1xnm_rr_otp_values,
+ .page = 0x200,
+ .size = 528,
+ },
+};
+
+static int hynix_nand_rr_init(struct nand_chip *chip)
+{
+ int i, ret = 0;
+ bool valid_jedecid;
+
+ valid_jedecid = hynix_nand_has_valid_jedecid(chip);
+
+ /*
+ * We only support read-retry for 1xnm NANDs, and those NANDs all
+ * expose a valid JEDEC ID.
+ */
+ if (valid_jedecid) {
+ u8 nand_tech = chip->id.data[5] >> 4;
+
+ /* 1xnm technology */
+ if (nand_tech == 4) {
+ for (i = 0; i < ARRAY_SIZE(hynix_mlc_1xnm_rr_otps);
+ i++) {
+
+ /*
+ * FIXME: Hynix recommend to copy the
+ * read-retry OTP area into a normal page.
+ */
+ ret = hynix_mlc_1xnm_rr_init(chip,
+ hynix_mlc_1xnm_rr_otps);
+ if (!ret)
+ break;
+ }
+ }
+ }
+
+ if (ret)
+ pr_warn("failed to initialize read-retry infrastructure");
+
+ return 0;
+}
+
static void hynix_nand_extract_oobsize(struct nand_chip *chip,
bool valid_jedecid)
{
@@ -254,17 +587,43 @@ static void hynix_nand_decode_id(struct nand_chip *chip)
hynix_nand_extract_scrambling_requirements(chip, valid_jedecid);
}
+static void hynix_nand_cleanup(struct nand_chip *chip)
+{
+ struct hynix_nand *hynix = nand_get_manufacturer_data(chip);
+
+ if (!hynix)
+ return;
+
+ kfree(hynix->read_retry);
+ kfree(hynix);
+ nand_set_manufacturer_data(chip, NULL);
+}
+
static int hynix_nand_init(struct nand_chip *chip)
{
+ struct hynix_nand *hynix;
+ int ret;
+
if (!nand_is_slc(chip))
chip->bbt_options |= NAND_BBT_SCANLASTPAGE;
else
chip->bbt_options |= NAND_BBT_SCAN2NDPAGE;
- return 0;
+ hynix = kzalloc(sizeof(*hynix), GFP_KERNEL);
+ if (!hynix)
+ return -ENOMEM;
+
+ nand_set_manufacturer_data(chip, hynix);
+
+ ret = hynix_nand_rr_init(chip);
+ if (ret)
+ hynix_nand_cleanup(chip);
+
+ return ret;
}
const struct nand_manufacturer_ops hynix_nand_manuf_ops = {
.detect = hynix_nand_decode_id,
.init = hynix_nand_init,
+ .cleanup = hynix_nand_cleanup,
};
--
2.7.4
More information about the linux-mtd
mailing list