[PATCH 2/2] mtd: brcmnand: Detect sticky ucorr ecc error on dma reads

[Boris Brezillon]

On Wed, 1 Jun 2016 12:50:56 -0400
Kamal Dasu <kamal.dasu at broadcom.com> wrote:

> Boris,
> 
> On Mon, May 30, 2016 at 4:50 AM, Boris Brezillon
> <boris.brezillon at free-electrons.com> wrote:
> > On Fri, 29 Apr 2016 16:21:25 -0400
> > Kamal Dasu <kdasu.kdev at gmail.com> wrote:
> >  
> >> This change provides a fix for controller bug where nand
> >> controller could have a possible sticky error after a PIO
> >> followed by a DMA read. The fix retries a read if we see
> >> a uncorr_ecc after read to detect such sticky errors.
> >>
> >> Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
> >> ---
> >>  drivers/mtd/nand/brcmnand/brcmnand.c | 15 ++++++++++++++-
> >>  1 file changed, 14 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/drivers/mtd/nand/brcmnand/brcmnand.c b/drivers/mtd/nand/brcmnand/brcmnand.c
> >> index 29a9abd..13c7784 100644
> >> --- a/drivers/mtd/nand/brcmnand/brcmnand.c
> >> +++ b/drivers/mtd/nand/brcmnand/brcmnand.c
> >> @@ -1555,9 +1555,11 @@ static int brcmnand_read(struct mtd_info *mtd, struct nand_chip *chip,
> >>       struct brcmnand_controller *ctrl = host->ctrl;
> >>       u64 err_addr = 0;
> >>       int err;
> >> +     bool retry = true;
> >>
> >>       dev_dbg(ctrl->dev, "read %llx -> %p\n", (unsigned long long)addr, buf);
> >>
> >> +try_dmaread:
> >>       brcmnand_write_reg(ctrl, BRCMNAND_UNCORR_COUNT, 0);
> >>
> >>       if (has_flash_dma(ctrl) && !oob && flash_dma_buf_ok(buf)) {
> >> @@ -1579,7 +1581,18 @@ static int brcmnand_read(struct mtd_info *mtd, struct nand_chip *chip,
> >>
> >>       if (mtd_is_eccerr(err)) {
> >>               int ret;
> >> -
> >> +             /*
> >> +              * On controller version >=7.0 if we are doing a DMA read
> >> +              * after a prior PIO read that reported uncorrectable error,
> >> +              * the DMA engine captures this error following DMA read
> >> +              * cleared only on subsequent DMA read, so just retry once
> >> +              * to clear a possible false error reported for current DMA
> >> +              * read
> >> +              */  
> >
> > Hm, shouldn't this BRCMNAND_UNCORR_COUNT bit be cleared just after
> > doing the PIO/DMA read instead of doing it before executing a new read?
> > This would solve your problem without the need for this extra retry, or
> > am I missing something?
> >  
> 
> Clearing the count registers or the intr registers does not clear the
> condition. Only a clean read (a page that does not have errors) clears
> the condition. So if this was a false error  ( page is really clean)
> and we read again, it will clear the condition.

This sounds like an expensive workaround, but you know the IP better
than I do, so I'll trust you ;).


-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com