[PATCH v1 3/5] mtd: atmel_nand: Support PMECC on SAMA5D2
Romain Izard
romain.izard.pro at gmail.com
Wed Jan 13 08:34:15 PST 2016
Starting with the SAMA5D2, there is a new revision of the Atmel PMECC
controller that can correct 32 bits in each sector. This controller is
not 100% compatible with the previous revision that corrected a maximum
of 24 bits by sector, as some register addresses overlap.
Using information from the device tree, we can configure the driver to
work with both versions.
Signed-off-by: Romain Izard <romain.izard.pro at gmail.com>
---
.../devicetree/bindings/mtd/atmel-nand.txt | 7 +++++--
drivers/mtd/nand/atmel_nand.c | 23 +++++++++++++++++++++-
drivers/mtd/nand/atmel_nand_ecc.h | 8 ++++++--
3 files changed, 33 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
index 89b0db9801b0..90887b430f03 100644
--- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
@@ -1,7 +1,10 @@
Atmel NAND flash
Required properties:
-- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand".
+- compatible: The possible values are:
+ "atmel,at91rm9200-nand"
+ "atmel,sama5d2-nand"
+ "atmel,sama5d4-nand"
- reg : should specify localbus address and size used for the chip,
and hardware ECC controller if available.
If the hardware ECC is PMECC, it should contain address and size for
@@ -22,7 +25,7 @@ Optional properties:
Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first",
"soft_bch".
- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware.
- Only supported by at91sam9x5 or later sam9 product.
+ Supported by AT91SAM9x5 or later SAM9 chips, and SAMA5 chips.
- atmel,pmecc-cap : error correct capability for Programmable Multibit ECC
Controller. Supported values are: 2, 4, 8, 12, 24.
- atmel,pmecc-sector-size : sector size for ECC computation. Supported values
diff --git a/drivers/mtd/nand/atmel_nand.c b/drivers/mtd/nand/atmel_nand.c
index e5d7e7e63f49..6fe50e2d291f 100644
--- a/drivers/mtd/nand/atmel_nand.c
+++ b/drivers/mtd/nand/atmel_nand.c
@@ -65,6 +65,7 @@ module_param(on_flash_bbt, int, 0);
struct atmel_nand_caps {
bool pmecc_correct_erase_page;
+ uint8_t pmecc_max_correction;
};
struct atmel_nand_nfc_priv {
@@ -146,6 +147,7 @@ struct atmel_nand_host {
int pmecc_cw_len; /* Length of codeword */
void __iomem *pmerrloc_base;
+ void __iomem *pmerrloc_el_base;
void __iomem *pmecc_rom_base;
/* lookup table for alpha_to and index_of */
@@ -817,7 +819,7 @@ static void pmecc_correct_data(struct mtd_info *mtd, uint8_t *buf, uint8_t *ecc,
sector_size = host->pmecc_sector_size;
while (err_nbr) {
- tmp = pmerrloc_readl_el_relaxed(host->pmerrloc_base, i) - 1;
+ tmp = pmerrloc_readl_el_relaxed(host->pmerrloc_el_base, i) - 1;
byte_pos = tmp / 8;
bit_pos = tmp % 8;
@@ -1208,6 +1210,8 @@ static int atmel_pmecc_nand_init_params(struct platform_device *pdev,
err_no = PTR_ERR(host->pmerrloc_base);
goto err;
}
+ host->pmerrloc_el_base = host->pmerrloc_base + ATMEL_PMERRLOC_SIGMAx +
+ (host->caps->pmecc_max_correction + 1) * 4;
if (!host->has_no_lookup_table) {
regs_rom = platform_get_resource(pdev, IORESOURCE_MEM, 3);
@@ -2307,17 +2311,34 @@ static int atmel_nand_remove(struct platform_device *pdev)
return 0;
}
+/*
+ * AT91RM9200 does not have PMECC or PMECC Errloc peripherals for
+ * BCH ECC. Combined with the "atmel,has-pmecc", it is used to describe
+ * devices from the SAM9 family that have those.
+ */
static struct atmel_nand_caps at91rm9200_caps = {
.pmecc_correct_erase_page = false,
+ .pmecc_max_correction = 24,
};
static struct atmel_nand_caps sama5d4_caps = {
.pmecc_correct_erase_page = true,
+ .pmecc_max_correction = 24,
+};
+
+/*
+ * The PMECC Errloc controller starting in SAMA5D2 is not compatible,
+ * as the increased correction strength requires more registers.
+ */
+static struct atmel_nand_caps sama5d2_caps = {
+ .pmecc_correct_erase_page = true,
+ .pmecc_max_correction = 32,
};
static const struct of_device_id atmel_nand_dt_ids[] = {
{ .compatible = "atmel,at91rm9200-nand", .data = &at91rm9200_caps },
{ .compatible = "atmel,sama5d4-nand", .data = &sama5d4_caps },
+ { .compatible = "atmel,sama5d2-nand", .data = &sama5d2_caps },
{ /* sentinel */ }
};
diff --git a/drivers/mtd/nand/atmel_nand_ecc.h b/drivers/mtd/nand/atmel_nand_ecc.h
index 668e7358f19b..ec964c43c932 100644
--- a/drivers/mtd/nand/atmel_nand_ecc.h
+++ b/drivers/mtd/nand/atmel_nand_ecc.h
@@ -108,7 +108,11 @@
#define PMERRLOC_ERR_NUM_MASK (0x1f << 8)
#define PMERRLOC_CALC_DONE (1 << 0)
#define ATMEL_PMERRLOC_SIGMAx 0x028 /* Error location SIGMA x */
-#define ATMEL_PMERRLOC_ELx 0x08c /* Error location x */
+
+/*
+ * The ATMEL_PMERRLOC_ELx register location depends from the number of
+ * bits corrected by the PMECC controller. Do not use it.
+ */
/* Register access macros for PMECC */
#define pmecc_readl_relaxed(addr, reg) \
@@ -136,7 +140,7 @@
readl_relaxed((addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
#define pmerrloc_readl_el_relaxed(addr, n) \
- readl_relaxed((addr) + ATMEL_PMERRLOC_ELx + ((n) * 4))
+ readl_relaxed((addr) + ((n) * 4))
/* Galois field dimension */
#define PMECC_GF_DIMENSION_13 13
--
2.5.0
More information about the linux-mtd
mailing list