[PATCH] mtd: jz4780_nand: replace if/else blocks with switch/case

[Brian Norris]

Using switch/case helps make this logic more clear and more robust. With
this structure:

 * it's clear that this driver only support ECC_{HW,SOFT,SOFT_BCH}; and

 * we can sanely handle new ECC unsupported modes (right now, this code
   makes incorrect assumptions about the possible values in the
   nand_ecc_modes_t enum; e.g., what happens with NAND_ECC_HW_OOB_FIRST?)

Signed-off-by: Brian Norris <computersforpeace at gmail.com>
Cc: Alex Smith <alex at alex-smith.me.uk>
Cc: Harvey Hunt <harvey.hunt at imgtec.com>
---
Compile tested only

 drivers/mtd/nand/jz4780_nand.c | 34 +++++++++++++++++++---------------
 1 file changed, 19 insertions(+), 15 deletions(-)

diff --git a/drivers/mtd/nand/jz4780_nand.c b/drivers/mtd/nand/jz4780_nand.c
index 17eb9f264187..aabee8f5627e 100644
--- a/drivers/mtd/nand/jz4780_nand.c
+++ b/drivers/mtd/nand/jz4780_nand.c
@@ -171,29 +171,33 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
 	chip->ecc.bytes = fls((1 + 8) * chip->ecc.size)	*
 				(chip->ecc.strength / 8);
 
-	if (nfc->bch && chip->ecc.mode == NAND_ECC_HW) {
+	switch (chip->ecc.mode) {
+	case NAND_ECC_HW:
+		if (!nfc->bch) {
+			dev_err(dev, "HW BCH selected, but BCH controller not found\n");
+			return -ENODEV;
+		}
+
 		chip->ecc.hwctl = jz4780_nand_ecc_hwctl;
 		chip->ecc.calculate = jz4780_nand_ecc_calculate;
 		chip->ecc.correct = jz4780_nand_ecc_correct;
-	} else if (!nfc->bch && chip->ecc.mode == NAND_ECC_HW) {
-		dev_err(dev, "HW BCH selected, but BCH controller not found\n");
-		return -ENODEV;
-	}
-
-	if (chip->ecc.mode == NAND_ECC_HW_SYNDROME) {
-		dev_err(dev, "ECC HW syndrome not supported\n");
-		return -EINVAL;
-	}
-
-	if (chip->ecc.mode != NAND_ECC_NONE)
+		/* fall through */
+	case NAND_ECC_SOFT:
+	case NAND_ECC_SOFT_BCH:
 		dev_info(dev, "using %s (strength %d, size %d, bytes %d)\n",
 			(nfc->bch) ? "hardware BCH" : "software ECC",
 			chip->ecc.strength, chip->ecc.size, chip->ecc.bytes);
-	else
+		break;
+	case NAND_ECC_NONE:
 		dev_info(dev, "not using ECC\n");
+		break;
+	default:
+		dev_err(dev, "ECC mode %d not supported\n", chip->ecc.mode);
+		return -EINVAL;
+	}
 
-	/* The NAND core will generate the ECC layout. */
-	if (chip->ecc.mode == NAND_ECC_SOFT || chip->ecc.mode == NAND_ECC_SOFT_BCH)
+	/* The NAND core will generate the ECC layout for SW ECC */
+	if (chip->ecc.mode != NAND_ECC_HW)
 		return 0;
 
 	/* Generate ECC layout. ECC codes are right aligned in the OOB area. */
-- 
2.6.0.rc2.230.g3dd15c0