[PATCH v9] mtd: spi-nor: Add support for S3AN spi-nor devices

[Cyrille Pitchen]

Le 13/12/2016 à 08:53, Marek Vasut a écrit :
> On 12/02/2016 12:31 PM, Ricardo Ribalda Delgado wrote:
>> Xilinx Spartan-3AN FPGAs contain an In-System Flash where they keep
>> their configuration data and (optionally) some user data.
>>
>> The protocol of this flash follows most of the spi-nor standard. With
>> the following differences:
>>
>> - Page size might not be a power of two.
>> - The address calculation (default addressing mode).
>> - The spi nor commands used.
>>
>> Protocol is described on Xilinx User Guide UG333
>>
>> Reviewed-by: Cyrille Pitchen <cyrille.pitchen at atmel.com>
>> Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda at gmail.com>
>> Cc: Boris Brezillon <boris.brezillon at free-electrons.com>
>> Cc: Brian Norris <computersforpeace at gmail.com>
>> Cc: Marek Vasut <marek.vasut at gmail.com>
> 
> [...]
> 
>> +static int s3an_nor_scan(const struct flash_info *info, struct spi_nor *nor)
>> +{
>> +	int ret;
>> +	u8 val;
>> +
>> +	ret = nor->read_reg(nor, SPINOR_OP_XRDSR, &val, 1);
>> +	if (ret < 0) {
>> +		dev_err(nor->dev, "error %d reading XRDSR\n", (int) ret);
>> +		return ret;
>> +	}
>> +
>> +	nor->erase_opcode = SPINOR_OP_XSE;
>> +	nor->program_opcode = SPINOR_OP_XPP;
>> +	nor->read_opcode = SPINOR_OP_READ;
>> +	nor->flags |= SNOR_F_NO_OP_CHIP_ERASE ;
> 
> NIT: You have an extra space before ;        ^
> 
>> +
>> +	/*
>> +	 * This flashes have a page size of 264 or 528 bytes (known as
>> +	 * Default addressing mode). It can be changed to a more standard
>> +	 * Power of two mode where the page size is 256/512. This comes
>> +	 * with a price: there is 3% less of space, the data is corrupted
>> +	 * and the page size cannot be changed back to default addressing
>> +	 * mode.
>> +	 *
>> +	 * The current addressing mode can be read from the XRDSR register
>> +	 * and should not be changed, because is a destructive operation.
>> +	 */
>> +	if (val & XSR_PAGESIZE) {
>> +		/* Flash in Power of 2 mode */
>> +		nor->page_size = (nor->page_size == 264) ? 256 : 512;
>> +		nor->mtd.writebufsize = nor->page_size;
>> +		nor->mtd.size = 8 * nor->page_size * info->n_sectors;
>> +		nor->mtd.erasesize = 8 * nor->page_size;
>> +	} else {
>> +		/* Flash in Default addressing mode */
>> +		nor->flags |= SNOR_F_S3AN_ADDR_DEFAULT;
>> +	}
>> +
>> +	return 0;
>> +}
> 
> Looks great otherwise:
> Reviewed-by: Marek Vasut <marek.vasut at gmail.com>
> 
Applied to git://github.com/spi-nor/linux.git

I've removed the additional SPACE before ';' as reported by Marek.

Thanks!