[PATCH v6, 4/8] spi: bcm-qspi: Add BSPI spi-nor flash controller driver
Kamal Dasu
kdasu.kdev at gmail.com
Wed Aug 24 15:04:25 PDT 2016
This change implements BSPI driver for Broadcom BRCMSTB, NS2,
NSP SoCs works in combination with the MSPI controller driver
and implements flash read acceleration and implements the
spi_flash_read() method. Both MSPI and BSPI controllers are
needed to access spi-nor flash.
Signed-off-by: Kamal Dasu <kdasu.kdev at gmail.com>
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy at broadcom.com>
---
drivers/spi/spi-bcm-qspi.c | 603 ++++++++++++++++++++++++++++++++++++++++++++-
drivers/spi/spi-bcm-qspi.h | 20 ++
2 files changed, 620 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c
index 4c1b9ba..8fff43e 100644
--- a/drivers/spi/spi-bcm-qspi.c
+++ b/drivers/spi/spi-bcm-qspi.c
@@ -38,6 +38,60 @@
#define DRIVER_NAME "bcm_qspi"
+
+/* BSPI register offsets */
+#define BSPI_REVISION_ID 0x000
+#define BSPI_SCRATCH 0x004
+#define BSPI_MAST_N_BOOT_CTRL 0x008
+#define BSPI_BUSY_STATUS 0x00c
+#define BSPI_INTR_STATUS 0x010
+#define BSPI_B0_STATUS 0x014
+#define BSPI_B0_CTRL 0x018
+#define BSPI_B1_STATUS 0x01c
+#define BSPI_B1_CTRL 0x020
+#define BSPI_STRAP_OVERRIDE_CTRL 0x024
+#define BSPI_FLEX_MODE_ENABLE 0x028
+#define BSPI_BITS_PER_CYCLE 0x02c
+#define BSPI_BITS_PER_PHASE 0x030
+#define BSPI_CMD_AND_MODE_BYTE 0x034
+#define BSPI_BSPI_FLASH_UPPER_ADDR_BYTE 0x038
+#define BSPI_BSPI_XOR_VALUE 0x03c
+#define BSPI_BSPI_XOR_ENABLE 0x040
+#define BSPI_BSPI_PIO_MODE_ENABLE 0x044
+#define BSPI_BSPI_PIO_IODIR 0x048
+#define BSPI_BSPI_PIO_DATA 0x04c
+
+/* RAF register offsets */
+#define BSPI_RAF_START_ADDR 0x100
+#define BSPI_RAF_NUM_WORDS 0x104
+#define BSPI_RAF_CTRL 0x108
+#define BSPI_RAF_FULLNESS 0x10c
+#define BSPI_RAF_WATERMARK 0x110
+#define BSPI_RAF_STATUS 0x114
+#define BSPI_RAF_READ_DATA 0x118
+#define BSPI_RAF_WORD_CNT 0x11c
+#define BSPI_RAF_CURR_ADDR 0x120
+
+/* Override mode masks */
+#define BSPI_STRAP_OVERRIDE_CTRL_OVERRIDE BIT(0)
+#define BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL BIT(1)
+#define BSPI_STRAP_OVERRIDE_CTRL_ADDR_4BYTE BIT(2)
+#define BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD BIT(3)
+#define BSPI_STRAP_OVERRIDE_CTRL_ENDAIN_MODE BIT(4)
+
+#define BSPI_ADDRLEN_3BYTES 3
+#define BSPI_ADDRLEN_4BYTES 4
+
+#define BSPI_RAF_STATUS_FIFO_EMPTY_MASK BIT(1)
+
+#define BSPI_RAF_CTRL_START_MASK BIT(0)
+#define BSPI_RAF_CTRL_CLEAR_MASK BIT(1)
+
+#define BSPI_BPP_MODE_SELECT_MASK BIT(8)
+#define BSPI_BPP_ADDR_SELECT_MASK BIT(16)
+
+#define BSPI_READ_LENGTH 256
+
/* MSPI register offsets */
#define MSPI_SPCR0_LSB 0x000
#define MSPI_SPCR0_MSB 0x004
@@ -108,8 +162,16 @@ struct bcm_qspi_parms {
u8 bits_per_word;
};
+struct bcm_xfer_mode {
+ bool flex_mode;
+ unsigned int width;
+ unsigned int addrlen;
+ unsigned int hp;
+};
+
enum base_type {
MSPI,
+ BSPI,
CHIP_SELECT,
BASEMAX,
};
@@ -140,13 +202,28 @@ struct bcm_qspi {
struct bcm_qspi_parms last_parms;
struct qspi_trans trans_pos;
int curr_cs;
+ int bspi_maj_rev;
+ int bspi_min_rev;
+ int bspi_enabled;
+ struct spi_flash_read_message *bspi_rf_msg;
+ u32 bspi_rf_msg_idx;
+ u32 bspi_rf_msg_len;
+ u32 bspi_rf_msg_status;
+ struct bcm_xfer_mode xfer_mode;
u32 s3_strap_override_ctrl;
+ bool bspi_mode;
bool big_endian;
int num_irqs;
struct bcm_qspi_dev_id *dev_ids;
struct completion mspi_done;
+ struct completion bspi_done;
};
+static inline bool has_bspi(struct bcm_qspi *qspi)
+{
+ return qspi->bspi_mode;
+}
+
/* Read qspi controller register*/
static inline u32 bcm_qspi_read(struct bcm_qspi *qspi, enum base_type type,
unsigned int offset)
@@ -161,6 +238,300 @@ static inline void bcm_qspi_write(struct bcm_qspi *qspi, enum base_type type,
bcm_qspi_writel(qspi->big_endian, data, qspi->base[type] + offset);
}
+/* BSPI helpers */
+static int bcm_qspi_bspi_busy_poll(struct bcm_qspi *qspi)
+{
+ int i;
+
+ /* this should normally finish within 10us */
+ for (i = 0; i < 1000; i++) {
+ if (!(bcm_qspi_read(qspi, BSPI, BSPI_BUSY_STATUS) & 1))
+ return 0;
+ udelay(1);
+ }
+ dev_warn(&qspi->pdev->dev, "timeout waiting for !busy_status\n");
+ return -EIO;
+}
+
+static inline bool bcm_qspi_bspi_ver_three(struct bcm_qspi *qspi)
+{
+ if (qspi->bspi_maj_rev < 4)
+ return true;
+ return false;
+}
+
+static void bcm_qspi_bspi_flush_prefetch_buffers(struct bcm_qspi *qspi)
+{
+ bcm_qspi_bspi_busy_poll(qspi);
+ /* Force rising edge for the b0/b1 'flush' field */
+ bcm_qspi_write(qspi, BSPI, BSPI_B0_CTRL, 1);
+ bcm_qspi_write(qspi, BSPI, BSPI_B1_CTRL, 1);
+ bcm_qspi_write(qspi, BSPI, BSPI_B0_CTRL, 0);
+ bcm_qspi_write(qspi, BSPI, BSPI_B1_CTRL, 0);
+}
+
+static int bcm_qspi_bspi_lr_is_fifo_empty(struct bcm_qspi *qspi)
+{
+ return (bcm_qspi_read(qspi, BSPI, BSPI_RAF_STATUS) &
+ BSPI_RAF_STATUS_FIFO_EMPTY_MASK);
+}
+
+static inline u32 bcm_qspi_bspi_lr_read_fifo(struct bcm_qspi *qspi)
+{
+ u32 data = bcm_qspi_read(qspi, BSPI, BSPI_RAF_READ_DATA);
+
+ /* BSPI v3 LR is LE only, convert data to host endianness */
+ if (bcm_qspi_bspi_ver_three(qspi))
+ data = le32_to_cpu(data);
+
+ return data;
+}
+
+static inline void bcm_qspi_bspi_lr_start(struct bcm_qspi *qspi)
+{
+ bcm_qspi_bspi_busy_poll(qspi);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_CTRL,
+ BSPI_RAF_CTRL_START_MASK);
+}
+
+static inline void bcm_qspi_bspi_lr_clear(struct bcm_qspi *qspi)
+{
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_CTRL,
+ BSPI_RAF_CTRL_CLEAR_MASK);
+ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
+}
+
+static void bcm_qspi_bspi_lr_data_read(struct bcm_qspi *qspi)
+{
+ u32 *buf = (u32 *)qspi->bspi_rf_msg->buf;
+ u32 data = 0;
+
+ dev_dbg(&qspi->pdev->dev, "xfer %p rx %p rxlen %d\n", qspi->bspi_rf_msg,
+ qspi->bspi_rf_msg->buf, qspi->bspi_rf_msg_len);
+ while (!bcm_qspi_bspi_lr_is_fifo_empty(qspi)) {
+ data = bcm_qspi_bspi_lr_read_fifo(qspi);
+ if (likely(qspi->bspi_rf_msg_len >= 4) &&
+ IS_ALIGNED((uintptr_t)buf, 4)) {
+ buf[qspi->bspi_rf_msg_idx++] = data;
+ qspi->bspi_rf_msg_len -= 4;
+ } else {
+ /* Read out remaining bytes, make sure*/
+ u8 *cbuf = (u8 *)&buf[qspi->bspi_rf_msg_idx];
+
+ data = cpu_to_le32(data);
+ while (qspi->bspi_rf_msg_len) {
+ *cbuf++ = (u8)data;
+ data >>= 8;
+ qspi->bspi_rf_msg_len--;
+ }
+ }
+ }
+}
+
+static void bcm_qspi_bspi_set_xfer_params(struct bcm_qspi *qspi, u8 cmd_byte,
+ int bpp, int bpc, int flex_mode)
+{
+ bcm_qspi_write(qspi, BSPI, BSPI_FLEX_MODE_ENABLE, 0);
+ bcm_qspi_write(qspi, BSPI, BSPI_BITS_PER_CYCLE, bpc);
+ bcm_qspi_write(qspi, BSPI, BSPI_BITS_PER_PHASE, bpp);
+ bcm_qspi_write(qspi, BSPI, BSPI_CMD_AND_MODE_BYTE, cmd_byte);
+ bcm_qspi_write(qspi, BSPI, BSPI_FLEX_MODE_ENABLE, flex_mode);
+}
+
+static int bcm_qspi_bspi_set_flex_mode(struct bcm_qspi *qspi, int width,
+ int addrlen, int hp)
+{
+ int bpc = 0, bpp = 0;
+ u8 command = SPINOR_OP_READ_FAST;
+ int flex_mode = 1, rv = 0;
+ bool spans_4byte = false;
+
+ dev_dbg(&qspi->pdev->dev, "set flex mode w %x addrlen %x hp %d\n",
+ width, addrlen, hp);
+
+ if (addrlen == BSPI_ADDRLEN_4BYTES) {
+ bpp = BSPI_BPP_ADDR_SELECT_MASK;
+ spans_4byte = true;
+ }
+
+ bpp |= 8;
+
+ switch (width) {
+ case SPI_NBITS_SINGLE:
+ if (addrlen == BSPI_ADDRLEN_3BYTES)
+ /* default mode, does not need flex_cmd */
+ flex_mode = 0;
+ else
+ command = SPINOR_OP_READ4_FAST;
+ break;
+ case SPI_NBITS_DUAL:
+ bpc = 0x00000001;
+ if (hp) {
+ bpc |= 0x00010100; /* address and mode are 2-bit */
+ bpp = BSPI_BPP_MODE_SELECT_MASK;
+ command = OPCODE_DIOR;
+ if (spans_4byte)
+ command = OPCODE_DIOR_4B;
+ } else {
+ command = SPINOR_OP_READ_1_1_2;
+ if (spans_4byte)
+ command = SPINOR_OP_READ4_1_1_2;
+ }
+ break;
+ case SPI_NBITS_QUAD:
+ bpc = 0x00000002;
+ if (hp) {
+ bpc |= 0x00020200; /* address and mode are 4-bit */
+ bpp = 4; /* dummy cycles */
+ bpp |= BSPI_BPP_ADDR_SELECT_MASK;
+ command = OPCODE_QIOR;
+ if (spans_4byte)
+ command = OPCODE_QIOR_4B;
+ } else {
+ command = SPINOR_OP_READ_1_1_4;
+ if (spans_4byte)
+ command = SPINOR_OP_READ4_1_1_4;
+ }
+ break;
+ default:
+ rv = -EINVAL;
+ break;
+ }
+
+ if (rv == 0)
+ bcm_qspi_bspi_set_xfer_params(qspi, command, bpp, bpc,
+ flex_mode);
+
+ return rv;
+}
+
+static int bcm_qspi_bspi_set_override(struct bcm_qspi *qspi, int width,
+ int addrlen, int hp)
+{
+ u32 data = bcm_qspi_read(qspi, BSPI, BSPI_STRAP_OVERRIDE_CTRL);
+
+ dev_dbg(&qspi->pdev->dev, "set override mode w %x addrlen %x hp %d\n",
+ width, addrlen, hp);
+
+ switch (width) {
+ case SPI_NBITS_SINGLE:
+ /* clear quad/dual mode */
+ data &= ~(BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD |
+ BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL);
+ break;
+
+ case SPI_NBITS_QUAD:
+ /* clear dual mode and set quad mode */
+ data &= ~BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL;
+ data |= BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD;
+ break;
+ case SPI_NBITS_DUAL:
+ /* clear quad mode set dual mode */
+ data &= ~BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD;
+ data |= BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ if (addrlen == BSPI_ADDRLEN_4BYTES)
+ /* set 4byte mode*/
+ data |= BSPI_STRAP_OVERRIDE_CTRL_ADDR_4BYTE;
+ else
+ /* clear 4 byte mode */
+ data &= ~BSPI_STRAP_OVERRIDE_CTRL_ADDR_4BYTE;
+
+ /* set the override mode */
+ data |= BSPI_STRAP_OVERRIDE_CTRL_OVERRIDE;
+ bcm_qspi_write(qspi, BSPI, BSPI_STRAP_OVERRIDE_CTRL, data);
+ bcm_qspi_bspi_set_xfer_params(qspi, SPINOR_OP_READ_FAST, 0, 0, 0);
+
+ return 0;
+}
+
+static int bcm_qspi_bspi_set_mode(struct bcm_qspi *qspi,
+ int width, int addrlen, int hp)
+{
+ int error = 0;
+
+ /* default mode */
+ qspi->xfer_mode.flex_mode = true;
+
+ if (!bcm_qspi_bspi_ver_three(qspi)) {
+ u32 val, mask;
+
+ val = bcm_qspi_read(qspi, BSPI, BSPI_STRAP_OVERRIDE_CTRL);
+ mask = BSPI_STRAP_OVERRIDE_CTRL_OVERRIDE;
+ if (val & mask || qspi->s3_strap_override_ctrl & mask) {
+ qspi->xfer_mode.flex_mode = false;
+ bcm_qspi_write(qspi, BSPI, BSPI_FLEX_MODE_ENABLE,
+ 0);
+
+ if ((val | qspi->s3_strap_override_ctrl) &
+ BSPI_STRAP_OVERRIDE_CTRL_DATA_DUAL)
+ width = SPI_NBITS_DUAL;
+ else if ((val | qspi->s3_strap_override_ctrl) &
+ BSPI_STRAP_OVERRIDE_CTRL_DATA_QUAD)
+ width = SPI_NBITS_QUAD;
+
+ error = bcm_qspi_bspi_set_override(qspi, width, addrlen,
+ hp);
+ }
+ }
+
+ if (qspi->xfer_mode.flex_mode)
+ error = bcm_qspi_bspi_set_flex_mode(qspi, width, addrlen, hp);
+
+ if (error) {
+ dev_warn(&qspi->pdev->dev,
+ "INVALID COMBINATION: width=%d addrlen=%d hp=%d\n",
+ width, addrlen, hp);
+ } else if (qspi->xfer_mode.width != width ||
+ qspi->xfer_mode.addrlen != addrlen ||
+ qspi->xfer_mode.hp != hp) {
+ qspi->xfer_mode.width = width;
+ qspi->xfer_mode.addrlen = addrlen;
+ qspi->xfer_mode.hp = hp;
+ dev_dbg(&qspi->pdev->dev,
+ "cs:%d %d-lane output, %d-byte address%s\n",
+ qspi->curr_cs,
+ qspi->xfer_mode.width,
+ qspi->xfer_mode.addrlen,
+ qspi->xfer_mode.hp != -1 ? ", hp mode" : "");
+ }
+
+ return error;
+}
+
+static void bcm_qspi_enable_bspi(struct bcm_qspi *qspi)
+{
+ if (!has_bspi(qspi) || (qspi->bspi_enabled))
+ return;
+
+ qspi->bspi_enabled = 1;
+ if ((bcm_qspi_read(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL) & 1) == 0)
+ return;
+
+ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
+ udelay(1);
+ bcm_qspi_write(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL, 0);
+ udelay(1);
+}
+
+static void bcm_qspi_disable_bspi(struct bcm_qspi *qspi)
+{
+ if (!has_bspi(qspi) || (!qspi->bspi_enabled))
+ return;
+
+ qspi->bspi_enabled = 0;
+ if ((bcm_qspi_read(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL) & 1))
+ return;
+
+ bcm_qspi_bspi_busy_poll(qspi);
+ bcm_qspi_write(qspi, BSPI, BSPI_MAST_N_BOOT_CTRL, 1);
+ udelay(1);
+}
+
static void bcm_qspi_chip_select(struct bcm_qspi *qspi, int cs)
{
u32 data = 0;
@@ -298,6 +669,8 @@ static void read_from_hw(struct bcm_qspi *qspi, int slots)
struct qspi_trans tp;
int slot;
+ bcm_qspi_disable_bspi(qspi);
+
if (slots > MSPI_NUM_CDRAM) {
/* should never happen */
dev_err(&qspi->pdev->dev, "%s: too many slots!\n", __func__);
@@ -368,6 +741,7 @@ static int write_to_hw(struct bcm_qspi *qspi, struct spi_device *spi)
int slot = 0, tstatus = 0;
u32 mspi_cdram = 0;
+ bcm_qspi_disable_bspi(qspi);
tp = qspi->trans_pos;
bcm_qspi_update_parms(qspi, spi, tp.trans);
@@ -414,6 +788,9 @@ static int write_to_hw(struct bcm_qspi *qspi, struct spi_device *spi)
write_cdram_slot(qspi, slot - 1, mspi_cdram);
}
+ if (has_bspi(qspi))
+ bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 1);
+
/* Must flush previous writes before starting MSPI operation */
mb();
/* Set cont | spe | spifie */
@@ -423,6 +800,118 @@ done:
return slot;
}
+static int bcm_qspi_bspi_flash_read(struct spi_device *spi,
+ struct spi_flash_read_message *msg)
+{
+ struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
+ u32 addr = 0, len, len_words;
+ int ret = 0;
+ unsigned long timeo = msecs_to_jiffies(100);
+
+ if (bcm_qspi_bspi_ver_three(qspi))
+ if (msg->addr_width == BSPI_ADDRLEN_4BYTES)
+ return -EIO;
+
+ bcm_qspi_chip_select(qspi, spi->chip_select);
+ bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
+
+ /*
+ * when using flex mode mode we need to send
+ * the upper address byte to bspi
+ */
+ if (bcm_qspi_bspi_ver_three(qspi) == false) {
+ addr = msg->from & 0xff000000;
+ bcm_qspi_write(qspi, BSPI,
+ BSPI_BSPI_FLASH_UPPER_ADDR_BYTE, addr);
+ }
+
+ if (!qspi->xfer_mode.flex_mode)
+ addr = msg->from;
+ else
+ addr = msg->from & 0x00ffffff;
+
+ /* set BSPI RAF buffer max read length */
+ len = msg->len;
+ if (len > BSPI_READ_LENGTH)
+ len = BSPI_READ_LENGTH;
+
+ if (bcm_qspi_bspi_ver_three(qspi) == true)
+ addr = (addr + 0xc00000) & 0xffffff;
+
+ reinit_completion(&qspi->bspi_done);
+ bcm_qspi_enable_bspi(qspi);
+ len_words = (len + 3) >> 2;
+ qspi->bspi_rf_msg = msg;
+ qspi->bspi_rf_msg_status = 0;
+ qspi->bspi_rf_msg_idx = 0;
+ qspi->bspi_rf_msg_len = len;
+ dev_dbg(&qspi->pdev->dev, "bspi xfr addr 0x%x len 0x%x", addr, len);
+
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_START_ADDR, addr);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_NUM_WORDS, len_words);
+ bcm_qspi_write(qspi, BSPI, BSPI_RAF_WATERMARK, 0);
+
+ /* Must flush previous writes before starting BSPI operation */
+ mb();
+
+ bcm_qspi_bspi_lr_start(qspi);
+ if (!wait_for_completion_timeout(&qspi->bspi_done, timeo)) {
+ dev_err(&qspi->pdev->dev, "timeout waiting for BSPI\n");
+ ret = -ETIMEDOUT;
+ } else {
+ /* set the return length for the caller */
+ msg->retlen = len;
+ }
+
+ return ret;
+}
+
+static int bcm_qspi_flash_read(struct spi_device *spi,
+ struct spi_flash_read_message *msg)
+{
+ struct bcm_qspi *qspi = spi_master_get_devdata(spi->master);
+ int ret = 0;
+ bool mspi_read = false;
+ u32 io_width, addrlen, addr, len;
+ u_char *buf;
+
+ buf = msg->buf;
+ addr = msg->from;
+ len = msg->len;
+
+ if (bcm_qspi_bspi_ver_three(qspi) == true) {
+ /*
+ * The address coming into this function is a raw flash offset.
+ * But for BSPI <= V3, we need to convert it to a remapped BSPI
+ * address. If it crosses a 4MB boundary, just revert back to
+ * using MSPI.
+ */
+ addr = (addr + 0xc00000) & 0xffffff;
+
+ if ((~ADDR_4MB_MASK & addr) ^
+ (~ADDR_4MB_MASK & (addr + len - 1)))
+ mspi_read = true;
+ }
+
+ /* non-aligned and very short transfers are handled by MSPI */
+ if (!IS_ALIGNED((uintptr_t)addr, 4) || !IS_ALIGNED((uintptr_t)buf, 4) ||
+ len < 4)
+ mspi_read = true;
+
+ if (mspi_read)
+ /* this will make the m25p80 read to fallback to mspi read */
+ return -EAGAIN;
+
+ io_width = msg->data_nbits ? msg->data_nbits : SPI_NBITS_SINGLE;
+ addrlen = msg->addr_width;
+ ret = bcm_qspi_bspi_set_mode(qspi, io_width, addrlen, -1);
+
+ if (!ret)
+ ret = bcm_qspi_bspi_flash_read(spi, msg);
+
+ return ret;
+}
+
static int bcm_qspi_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *trans)
@@ -469,13 +958,76 @@ static irqreturn_t bcm_qspi_mspi_l2_isr(int irq, void *dev_id)
bcm_qspi_write(qspi, MSPI, MSPI_MSPI_STATUS, status);
complete(&qspi->mspi_done);
return IRQ_HANDLED;
- } else {
- return IRQ_NONE;
}
+
+ return IRQ_NONE;
+}
+
+static irqreturn_t bcm_qspi_bspi_lr_l2_isr(int irq, void *dev_id)
+{
+ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
+ struct bcm_qspi *qspi = qspi_dev_id->dev;
+ u32 status;
+
+ if (qspi->bspi_enabled && qspi->bspi_rf_msg) {
+ bcm_qspi_bspi_lr_data_read(qspi);
+ if (qspi->bspi_rf_msg_len == 0) {
+ qspi->bspi_rf_msg = NULL;
+ if (qspi->bspi_rf_msg_status)
+ bcm_qspi_bspi_lr_clear(qspi);
+ else
+ bcm_qspi_bspi_flush_prefetch_buffers(qspi);
+ }
+ }
+
+ status = (qspi_dev_id->irqp->mask & INTR_BSPI_LR_SESSION_DONE_MASK);
+ if (qspi->bspi_enabled && status && qspi->bspi_rf_msg_len == 0)
+ complete(&qspi->bspi_done);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t bcm_qspi_bspi_lr_err_l2_isr(int irq, void *dev_id)
+{
+ struct bcm_qspi_dev_id *qspi_dev_id = dev_id;
+ struct bcm_qspi *qspi = qspi_dev_id->dev;
+
+ dev_err(&qspi->pdev->dev, "BSPI INT error\n");
+ qspi->bspi_rf_msg_status = -EIO;
+ complete(&qspi->bspi_done);
+ return IRQ_HANDLED;
}
static const struct bcm_qspi_irq qspi_irq_tab[] = {
{
+ .irq_name = "spi_lr_fullness_reached",
+ .irq_handler = bcm_qspi_bspi_lr_l2_isr,
+ .mask = INTR_BSPI_LR_FULLNESS_REACHED_MASK,
+ },
+ {
+ .irq_name = "spi_lr_session_aborted",
+ .irq_handler = bcm_qspi_bspi_lr_err_l2_isr,
+ .mask = INTR_BSPI_LR_SESSION_ABORTED_MASK,
+ },
+ {
+ .irq_name = "spi_lr_impatient",
+ .irq_handler = bcm_qspi_bspi_lr_err_l2_isr,
+ .mask = INTR_BSPI_LR_IMPATIENT_MASK,
+ },
+ {
+ .irq_name = "spi_lr_session_done",
+ .irq_handler = bcm_qspi_bspi_lr_l2_isr,
+ .mask = INTR_BSPI_LR_SESSION_DONE_MASK,
+ },
+#ifdef QSPI_INT_DEBUG
+ /* this interrupt is for debug purposes only, dont request irq */
+ {
+ .irq_name = "spi_lr_overread",
+ .irq_handler = bcm_qspi_bspi_lr_err_l2_isr,
+ .mask = INTR_BSPI_LR_OVERREAD_MASK,
+ },
+#endif
+ {
.irq_name = "mspi_done",
.irq_handler = bcm_qspi_mspi_l2_isr,
.mask = INTR_MSPI_DONE_MASK,
@@ -487,6 +1039,24 @@ static const struct bcm_qspi_irq qspi_irq_tab[] = {
},
};
+static void bcm_qspi_bspi_init(struct bcm_qspi *qspi)
+{
+ u32 val = 0;
+
+ val = bcm_qspi_read(qspi, BSPI, BSPI_REVISION_ID);
+ qspi->bspi_maj_rev = (val >> 8) & 0xff;
+ qspi->bspi_min_rev = val & 0xff;
+ if (!(bcm_qspi_bspi_ver_three(qspi))) {
+ /* Force mapping of BSPI address -> flash offset */
+ bcm_qspi_write(qspi, BSPI, BSPI_BSPI_XOR_VALUE, 0);
+ bcm_qspi_write(qspi, BSPI, BSPI_BSPI_XOR_ENABLE, 1);
+ }
+ qspi->bspi_enabled = 1;
+ bcm_qspi_disable_bspi(qspi);
+ bcm_qspi_write(qspi, BSPI, BSPI_B0_CTRL, 0);
+ bcm_qspi_write(qspi, BSPI, BSPI_B1_CTRL, 0);
+}
+
static void bcm_qspi_hw_init(struct bcm_qspi *qspi)
{
struct bcm_qspi_parms parms;
@@ -501,11 +1071,17 @@ static void bcm_qspi_hw_init(struct bcm_qspi *qspi)
parms.bits_per_word = 8;
parms.speed_hz = qspi->max_speed_hz;
bcm_qspi_hw_set_parms(qspi, &parms);
+
+ if (has_bspi(qspi))
+ bcm_qspi_bspi_init(qspi);
}
static void bcm_qspi_hw_uninit(struct bcm_qspi *qspi)
{
bcm_qspi_write(qspi, MSPI, MSPI_SPCR2, 0);
+ if (has_bspi(qspi))
+ bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
+
}
static const struct of_device_id bcm_qspi_of_match[] = {
@@ -515,7 +1091,7 @@ static const struct of_device_id bcm_qspi_of_match[] = {
MODULE_DEVICE_TABLE(of, bcm_qspi_of_match);
int bcm_qspi_probe(struct platform_device *pdev,
- struct bcm_qspi_soc_intc *soc)
+ struct bcm_qspi_soc_intc *soc_intc)
{
struct device *dev = &pdev->dev;
struct bcm_qspi *qspi;
@@ -549,6 +1125,7 @@ int bcm_qspi_probe(struct platform_device *pdev,
master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_RX_DUAL | SPI_RX_QUAD;
master->setup = bcm_qspi_setup;
master->transfer_one = bcm_qspi_transfer_one;
+ master->spi_flash_read = bcm_qspi_flash_read;
master->cleanup = bcm_qspi_cleanup;
master->dev.of_node = dev->of_node;
master->num_chipselect = NUM_CHIPSELECT;
@@ -573,6 +1150,20 @@ int bcm_qspi_probe(struct platform_device *pdev,
goto qspi_probe_err;
}
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "bspi");
+ if (res) {
+ qspi->base[BSPI] = devm_ioremap_resource(dev, res);
+ if (IS_ERR(qspi->base[BSPI])) {
+ ret = PTR_ERR(qspi->base[BSPI]);
+ goto qspi_probe_err;
+ }
+ qspi->bspi_mode = true;
+ } else {
+ qspi->bspi_mode = false;
+ }
+
+ dev_info(dev, "using %smspi mode\n", qspi->bspi_mode ? "bspi-" : "");
+
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cs_reg");
if (res) {
qspi->base[CHIP_SELECT] = devm_ioremap_resource(dev, res);
@@ -635,9 +1226,15 @@ int bcm_qspi_probe(struct platform_device *pdev,
bcm_qspi_hw_init(qspi);
init_completion(&qspi->mspi_done);
+ init_completion(&qspi->bspi_done);
qspi->curr_cs = -1;
platform_set_drvdata(pdev, qspi);
+
+ qspi->xfer_mode.width = -1;
+ qspi->xfer_mode.addrlen = -1;
+ qspi->xfer_mode.hp = -1;
+
ret = devm_spi_register_master(&pdev->dev, master);
if (ret < 0) {
dev_err(dev, "can't register master\n");
diff --git a/drivers/spi/spi-bcm-qspi.h b/drivers/spi/spi-bcm-qspi.h
index 8d4d385..65c363b 100644
--- a/drivers/spi/spi-bcm-qspi.h
+++ b/drivers/spi/spi-bcm-qspi.h
@@ -20,6 +20,26 @@
#include <linux/types.h>
#include <linux/io.h>
+/* BSPI interrupt masks */
+#define INTR_BSPI_LR_OVERREAD_MASK BIT(4)
+#define INTR_BSPI_LR_SESSION_DONE_MASK BIT(3)
+#define INTR_BSPI_LR_IMPATIENT_MASK BIT(2)
+#define INTR_BSPI_LR_SESSION_ABORTED_MASK BIT(1)
+#define INTR_BSPI_LR_FULLNESS_REACHED_MASK BIT(0)
+
+#define BSPI_LR_INTERRUPTS_DATA \
+ (INTR_BSPI_LR_SESSION_DONE_MASK | \
+ INTR_BSPI_LR_FULLNESS_REACHED_MASK)
+
+#define BSPI_LR_INTERRUPTS_ERROR \
+ (INTR_BSPI_LR_OVERREAD_MASK | \
+ INTR_BSPI_LR_IMPATIENT_MASK | \
+ INTR_BSPI_LR_SESSION_ABORTED_MASK)
+
+#define BSPI_LR_INTERRUPTS_ALL \
+ (BSPI_LR_INTERRUPTS_ERROR | \
+ BSPI_LR_INTERRUPTS_DATA)
+
/* MSPI Interrupt masks */
#define INTR_MSPI_HALTED_MASK BIT(6)
#define INTR_MSPI_DONE_MASK BIT(5)
--
1.9.1
More information about the linux-mtd
mailing list