[PATCH v6 4/4] MIPS: dts: jz4780/ci20: Add NEMC, BCH and NAND device tree nodes

[Alex Smith]

From: Alex Smith <alex.smith at imgtec.com>

Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
and make use of them in the Ci20 device tree to add a node for the
board's NAND.

Note that since the pinctrl driver is not yet upstream, this includes
neither pin configuration nor busy/write-protect GPIO pins for the
NAND. Use of the NAND relies on the boot loader to have left the pins
configured in a usable state, which should be the case when booted
from the NAND.

Signed-off-by: Alex Smith <alex.smith at imgtec.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel at imgtec.com>
Cc: David Woodhouse <dwmw2 at infradead.org>
Cc: Brian Norris <computersforpeace at gmail.com>
Cc: Paul Burton <paul.burton at imgtec.com>
Cc: linux-mtd at lists.infradead.org
Cc: devicetree at vger.kernel.org
Cc: linux-kernel at vger.kernel.org
Cc: linux-mips at linux-mips.org
---
v5 -> v6:
 - No change.

v4 -> v5:
 - New patch adding DT nodes for the NAND so that the driver can be
   tested.
---
 arch/mips/boot/dts/ingenic/ci20.dts    | 51 ++++++++++++++++++++++++++++++++++
 arch/mips/boot/dts/ingenic/jz4780.dtsi | 26 +++++++++++++++++
 2 files changed, 77 insertions(+)

diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
index 9fcb9e7..c0c8a64 100644
--- a/arch/mips/boot/dts/ingenic/ci20.dts
+++ b/arch/mips/boot/dts/ingenic/ci20.dts
@@ -42,3 +42,54 @@
 &uart4 {
 	status = "okay";
 };
+
+&nemc {
+	status = "okay";
+
+	nand: nand at 1 {
+		compatible = "ingenic,jz4780-nand";
+		reg = <1 0 0x1000000>;
+
+		ingenic,nemc-tAS = <10>;
+		ingenic,nemc-tAH = <5>;
+		ingenic,nemc-tBP = <10>;
+		ingenic,nemc-tAW = <15>;
+		ingenic,nemc-tSTRV = <100>;
+
+		ingenic,bch-controller = <&bch>;
+		ingenic,ecc-size = <1024>;
+		ingenic,ecc-strength = <24>;
+
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		partition at 0 {
+			label = "u-boot-spl";
+			reg = <0x0 0x0 0x0 0x800000>;
+		};
+
+		partition at 0x800000 {
+			label = "u-boot";
+			reg = <0x0 0x800000 0x0 0x200000>;
+		};
+
+		partition at 0xa00000 {
+			label = "u-boot-env";
+			reg = <0x0 0xa00000 0x0 0x200000>;
+		};
+
+		partition at 0xc00000 {
+			label = "boot";
+			reg = <0x0 0xc00000 0x0 0x4000000>;
+		};
+
+		partition at 0x8c00000 {
+			label = "system";
+			reg = <0x0 0x4c00000 0x1 0xfb400000>;
+		};
+	};
+};
+
+&bch {
+	status = "okay";
+};
diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
index 65389f6..b868b42 100644
--- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
+++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
@@ -108,4 +108,30 @@
 
 		status = "disabled";
 	};
+
+	nemc: nemc at 13410000 {
+		compatible = "ingenic,jz4780-nemc";
+		reg = <0x13410000 0x10000>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <1 0 0x1b000000 0x1000000
+			  2 0 0x1a000000 0x1000000
+			  3 0 0x19000000 0x1000000
+			  4 0 0x18000000 0x1000000
+			  5 0 0x17000000 0x1000000
+			  6 0 0x16000000 0x1000000>;
+
+		clocks = <&cgu JZ4780_CLK_NEMC>;
+
+		status = "disabled";
+	};
+
+	bch: bch at 134d0000 {
+		compatible = "ingenic,jz4780-bch";
+		reg = <0x134d0000 0x10000>;
+
+		clocks = <&cgu JZ4780_CLK_BCH>;
+
+		status = "disabled";
+	};
 };
-- 
2.5.2