Cannot mount ubifs partition
Richard Weinberger
richard at nod.at
Wed May 13 01:50:14 PDT 2015
Am 13.05.2015 um 10:48 schrieb Michael Niarchos:
>
>
> On 05/13/2015 09:49 AM, Richard Weinberger wrote:
>> On Wed, May 13, 2015 at 8:25 AM, Michael Niarchos
>> <michael.niarchos at gmail.com> wrote:
>>> On 13-May-15 06:05, Brian Norris wrote:
>>>>
>>>> On Tue, May 12, 2015 at 10:38:31PM +0300, Michael N wrote:
>>>>>
>>>>> I am using a Zynq7000 with NAND 512MB and I am trying to deploy Linux on
>>>>> NAND
>>>>> memory. I use a custom built kernel with minimal features (UBI and UBIFS
>>>>> support are enabled and mtd-utils installed). I can ubiformat an mtd
>>>>> partition, I
>>>>> can ubiattach and ubidetach it but whenever I try to mount the
>>>>> partition I get this error.
>>>>>
>>>>> mount: mounting /dev/ubi0:ubi-rootfs on /mnt/ubifs failed:
>>>>> No such device
>>>>
>>>> What's the exact mount command you're running? Did you take a look at
>>>> the MTD FAQ?
>>>>
>>>> http://linux-mtd.infradead.org/faq/ubifs.html#L_mount_ubif
>>>
>>>
>>> I am running this command:
>>>
>>> $ mount -t ubifs ubi0:ubi-rootfs /mnt/ubifs
>>
>> Does it work if you use the device node? i.e. /dev/ubi0_X?
>> Is it attached?
>
> root at zx3-pm3-zynq7:~# ubiattach /dev/ubi_ctrl -m 2
> [ 115.549805] UBI: attaching mtd2 to ubi0
> [ 115.787102] mmc0: Card removed during transfer!
> [ 115.791560] mmc0: Resetting controller.
> [ 115.803396] mmc0: Card removed during transfer!
> [ 115.807853] mmc0: Resetting controller.
> [ 119.024116] UBI: scanning is finished
> [ 119.056419] UBI: attached mtd2 (name "nand-rootfs", size 506 MiB) to ubi0
> [ 119.063272] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
> [ 119.070053] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
> [ 119.076670] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
> [ 119.083579] UBI: good PEBs: 4044, bad PEBs: 4, corrupted PEBs: 0
> [ 119.089580] UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
> [ 119.096636] UBI: max/mean erase counter: 6/2, WL threshold: 4096, image sequence number: 1208887967
> [ 119.105709] UBI: available PEBs: 0, total reserved PEBs: 4044, PEBs reserved for bad PEB handling: 76
> [ 119.115500] UBI: background thread "ubi_bgt0d" started, PID 933
> UBI device number 0, total 4044 LEBs (513490944 bytes, 489.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)
> root at zx3-pm3-zynq7:~# mount -t ubifs /dev/ubi0_0 /mnt/
> mount: mounting /dev/ubi0_0 on /mnt/ failed: No such device
Ahh, -m 2...
What does ubinfo -a print?
Thanks,
//richard
More information about the linux-mtd
mailing list