[PATCH v10 3/3] MIPS: dts: jz4780/ci20: Add NEMC, BCH and NAND device tree nodes

Boris Brezillon boris.brezillon at free-electrons.com
Mon Dec 28 00:27:38 PST 2015


On Thu, 24 Dec 2015 12:20:15 +0000
Harvey Hunt <harvey.hunt at imgtec.com> wrote:

> From: Alex Smith <alex.smith at imgtec.com>
> 
> Add device tree nodes for the NEMC and BCH to the JZ4780 device tree,
> and make use of them in the Ci20 device tree to add a node for the
> board's NAND.
> 
> Note that since the pinctrl driver is not yet upstream, this includes
> neither pin configuration nor busy/write-protect GPIO pins for the
> NAND. Use of the NAND relies on the boot loader to have left the pins
> configured in a usable state, which should be the case when booted
> from the NAND.
> 
> Signed-off-by: Alex Smith <alex.smith at imgtec.com>
> Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel at imgtec.com>
> Cc: David Woodhouse <dwmw2 at infradead.org>
> Cc: Brian Norris <computersforpeace at gmail.com>
> Cc: Paul Burton <paul.burton at imgtec.com>
> Cc: linux-mtd at lists.infradead.org
> Cc: devicetree at vger.kernel.org
> Cc: linux-kernel at vger.kernel.org
> Cc: linux-mips at linux-mips.org
> Cc: robh at kernel.org
> Signed-off-by: Harvey Hunt <harvey.hunt at imgtec.com>

Reviewed-by: Boris Brezillon <boris.brezillon at free-electrons.com>

> ---
> v9 -> v10:
>  - No change.
> 
> v8 -> v9:
>  - Represent the partition table as a subnode of a NAND chip. 
> 
> v7 -> v8:
>  - Describe the NAND chips as children nodes of the NAND controller.
>  - Remove ingenic, prefix from ECC settings.
>  - Renamed some ECC settings.
> 
> v6 -> v7:
>  - Add nand-ecc-mode to DT.
>  - Add nand-on-flash-bbt to DT.
> 
> v4 -> v5:
>  - New patch adding DT nodes for the NAND so that the driver can be
>    tested.
> 
>  arch/mips/boot/dts/ingenic/ci20.dts    | 63 ++++++++++++++++++++++++++++++++++
>  arch/mips/boot/dts/ingenic/jz4780.dtsi | 26 ++++++++++++++
>  2 files changed, 89 insertions(+)
> 
> diff --git a/arch/mips/boot/dts/ingenic/ci20.dts b/arch/mips/boot/dts/ingenic/ci20.dts
> index 9fcb9e7..782258c 100644
> --- a/arch/mips/boot/dts/ingenic/ci20.dts
> +++ b/arch/mips/boot/dts/ingenic/ci20.dts
> @@ -42,3 +42,66 @@
>  &uart4 {
>  	status = "okay";
>  };
> +
> +&nemc {
> +	status = "okay";
> +
> +	nandc: nand-controller at 1 {
> +		compatible = "ingenic,jz4780-nand";
> +		reg = <1 0 0x1000000>;
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ingenic,bch-controller = <&bch>;
> +
> +		ingenic,nemc-tAS = <10>;
> +		ingenic,nemc-tAH = <5>;
> +		ingenic,nemc-tBP = <10>;
> +		ingenic,nemc-tAW = <15>;
> +		ingenic,nemc-tSTRV = <100>;
> +
> +		nand at 1 {
> +			reg = <1>;
> +
> +			nand-ecc-step-size = <1024>;
> +			nand-ecc-strength = <24>;
> +			nand-ecc-mode = "hw";
> +			nand-on-flash-bbt;
> +
> +			partitions {
> +				#address-cells = <2>;
> +				#size-cells = <2>;
> +
> +				partition at 0 {
> +					label = "u-boot-spl";
> +					reg = <0x0 0x0 0x0 0x800000>;
> +				};
> +
> +				partition at 0x800000 {
> +					label = "u-boot";
> +					reg = <0x0 0x800000 0x0 0x200000>;
> +				};
> +
> +				partition at 0xa00000 {
> +					label = "u-boot-env";
> +					reg = <0x0 0xa00000 0x0 0x200000>;
> +				};
> +
> +				partition at 0xc00000 {
> +					label = "boot";
> +					reg = <0x0 0xc00000 0x0 0x4000000>;
> +				};
> +
> +				partition at 0x8c00000 {
> +					label = "system";
> +					reg = <0x0 0x4c00000 0x1 0xfb400000>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&bch {
> +	status = "okay";
> +};
> diff --git a/arch/mips/boot/dts/ingenic/jz4780.dtsi b/arch/mips/boot/dts/ingenic/jz4780.dtsi
> index 65389f6..b868b42 100644
> --- a/arch/mips/boot/dts/ingenic/jz4780.dtsi
> +++ b/arch/mips/boot/dts/ingenic/jz4780.dtsi
> @@ -108,4 +108,30 @@
>  
>  		status = "disabled";
>  	};
> +
> +	nemc: nemc at 13410000 {
> +		compatible = "ingenic,jz4780-nemc";
> +		reg = <0x13410000 0x10000>;
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		ranges = <1 0 0x1b000000 0x1000000
> +			  2 0 0x1a000000 0x1000000
> +			  3 0 0x19000000 0x1000000
> +			  4 0 0x18000000 0x1000000
> +			  5 0 0x17000000 0x1000000
> +			  6 0 0x16000000 0x1000000>;
> +
> +		clocks = <&cgu JZ4780_CLK_NEMC>;
> +
> +		status = "disabled";
> +	};
> +
> +	bch: bch at 134d0000 {
> +		compatible = "ingenic,jz4780-bch";
> +		reg = <0x134d0000 0x10000>;
> +
> +		clocks = <&cgu JZ4780_CLK_BCH>;
> +
> +		status = "disabled";
> +	};
>  };



-- 
Boris Brezillon, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com



More information about the linux-mtd mailing list