[PATCH v4 3/5] mtd: devices: m25p80: add support for mmap read request

[Vignesh R]

Hi,

On 12/03/2015 03:12 PM, Cyrille Pitchen wrote:
> Hi Vignesh,
> 
> Le 30/11/2015 06:15, Vignesh R a écrit :
>> Certain spi controllers may provide accelerated interface to read from
>> m25p80 type flash devices. This interface provides better read
>> performance than regular SPI interface.
>> Call spi_flash_read(), if supported, to make use of such interface.
>>
>> Signed-off-by: Vignesh R <vigneshr at ti.com>
>> ---
>>
>> v4: 
>>  * Use spi_flash_read_message struct to pass args.
>>  * support passing of opcode/addr/data nbits.
>>
>>  drivers/mtd/devices/m25p80.c | 20 ++++++++++++++++++++
>>  1 file changed, 20 insertions(+)
>>
>> diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
>> index fe9ceb7b5405..00094a668c62 100644
>> --- a/drivers/mtd/devices/m25p80.c
>> +++ b/drivers/mtd/devices/m25p80.c
>> @@ -131,6 +131,26 @@ static int m25p80_read(struct spi_nor *nor, loff_t from, size_t len,
>>  	/* convert the dummy cycles to the number of bytes */
>>  	dummy /= 8;
>>  
>> +	if (spi_flash_read_supported(spi)) {
>> +		struct spi_flash_read_message msg;
>> +		int ret;
>> +
>> +		msg.buf = buf;
>> +		msg.from = from;
>> +		msg.len = len;
>> +		msg.read_opcode = nor->read_opcode;
>> +		msg.addr_width = nor->addr_width;
>> +		msg.dummy_bytes = dummy;
>> +		/* TODO: Support other combinations */
>> +		msg.opcode_nbits = SPI_NBITS_SINGLE;
>> +		msg.addr_nbits = SPI_NBITS_SINGLE;
>> +		msg.data_nbits = m25p80_rx_nbits(nor);
> 
> I wanted to let you know that the support of other SPI protocols has already
> been implemented by this series:
> http://lists.infradead.org/pipermail/linux-arm-kernel/2015-September/371170.html
> 
> patches 2 & 3 handle the probing of the (Q)SPI memory in spi_nor_scan() and
> select the right protocols for register read/write, memory read, memory write,
> and memory erase operations. The choice is done according to both the memory
> and SPI controller capabilities.
> 
> patch 4 updates the m25p80 driver to take advantage of the bandwidth increase
> allowed by QSPI protocols. For instance, the Atmel QSPI controller, like TI
> one, maps the SPI NOR memory to the system bus. Yesterday I ran mtd_speedtest
> to compare Fast Read 1-1-1 (0x0b) and Fast Read 1-1-4 (0x6b). The SPI clock
> frequency was limited to 83MHz. The QSPI memory is a Micron n25q128a13.
> 
> I only had to change the mode argument of spi_nor_scan() from SPI_NOR_QUAD to
> SPI_NOR_FAST in the atmel_quadspi driver (based on fsl-quadspi driver from
> Freescale since Atmel's driver also uses the system bus mapping for memory
> write operations) to force the spi-nor framework to choose the SPI 1-1-1
> protocol instead of the SPI-1-1-4.
> 
> 1 - Fast Read 1-1-1
> 
> mtd_speedtest: testing eraseblock write speed
> mtd_speedtest: eraseblock read speed is 9319 KiB/s
> [...]
> mtd_speedtest: testing page read speed
> mtd_speedtest: page read speed is 6649 KiB/s
> [...]
> mtd_speedtest: testing 2 page read speed
> mtd_speedtest: 2 page read speed is 7757 KiB/s
> 
> 2 - Fast Read 1-1-4
> 
> mtd_speedtest: testing eraseblock read speed
> mtd_speedtest: eraseblock read speed is 30117 KiB/s
> [...]
> mtd_speedtest: testing page read speed
> mtd_speedtest: page read speed is 13096 KiB/s
> [...]
> mtd_speedtest: testing 2 page read speed
> mtd_speedtest: 2 page read speed is 18224 KiB/s
> 
> So the performance improvements are:
> eraseblock read speed (65536 bytes) : +223%
> page read speed (512 bytes)         :  +97%
> 2 page read speed (1024 bytes)      : +135%
> 
> 
> That's why I believe that you could take advantage of these performance
> improvements in the TI (Q)SPI controller driver.
> 

Well, I based my patches on linux-next as per Brian's suggestion. If
patches to support other flash protocol modes are accepted, I would be
happy to rebase and make use of other modes. It would just be the matter
of populating msg.{opcode/addr}_n_bits correctly.


> 
> Also please note that you may have to add in the struct spi_flash_read_message
> two other fields for the number of option/mode cycles and their value.
> Option/mode cycles are sent between the address and dummy cycles. They are
> used by some memory manufacturers such as Spansion, Micron and Macronix to
> enter/leave their continuous read mode.
> So if uninitialized dummy cycles are interpreted by the QSPI memory as
> option/mode cycles, depending on the actual value, the memory may enter by
> mistake in continuous mode. Once in continuous mode, the command op code byte
> must not be sent and is not expected by the memory: the memory implicitly uses
> the read op code sent in the SPI message which triggered the memory to enter
> continuous read mode. Next SPI messages start from the address cycles until
> the right option/mode cycles are sent to leave the continuous read mode.
> 
> Currently the mtd layer doesn't use this feature but it should be aware of it.
> That's why I believe we'll have to address this point in spi_nor_scan() and the
> "regular" m25p80() sooner or later.
> 

Above feature can be added incrementally over this series, (as and when
m25p80 is updated) moreover ti-qspi controller does not support
option/mode cycles in memory-mapped mode, so I wont be able to test this
feature anyway.


-- 
Regards
Vignesh