[PATCH v2 3/3] nand: omap2: Replace pr_err with dev_err
Ezequiel Garcia
ezequiel at vanguardiasur.com.ar
Mon Sep 8 07:35:50 PDT 2014
On 08 Sep 02:57 PM, Roger Quadros wrote:
> Hi Ezequiel,
>
> On 09/08/2014 02:27 PM, Ezequiel Garcia wrote:
> > Usage of pr_err is frowned upon, so replace it with dev_err.
> > Aditionally, the message on nand_bch_init() error is redundant,
> > since proper error is showed if the function fails.
> >
> > Signed-off-by: Ezequiel Garcia <ezequiel at vanguardiasur.com.ar>
> > ---
> > drivers/mtd/nand/omap2.c | 26 ++++++++++++++------------
> > 1 file changed, 14 insertions(+), 12 deletions(-)
> >
> > diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
> > index f97a4ff..eb5e898 100644
> > --- a/drivers/mtd/nand/omap2.c
> > +++ b/drivers/mtd/nand/omap2.c
> > @@ -1375,7 +1375,7 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data,
> > erased_ecc_vec = bch16_vector;
> > break;
> > default:
> > - pr_err("invalid driver configuration\n");
> > + dev_err(&info->pdev->dev, "invalid driver configuration\n");
> > return -EINVAL;
> > }
> >
> > @@ -1446,7 +1446,8 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data,
> > err = 0;
> > for (i = 0; i < eccsteps; i++) {
> > if (err_vec[i].error_uncorrectable) {
> > - pr_err("nand: uncorrectable bit-flips found\n");
> > + dev_err(&info->pdev->dev,
> > + "uncorrectable bit-flips found\n");
> > err = -EBADMSG;
> > } else if (err_vec[i].error_reported) {
> > for (j = 0; j < err_vec[i].error_count; j++) {
> > @@ -1483,8 +1484,9 @@ static int omap_elm_correct_data(struct mtd_info *mtd, u_char *data,
> > 1 << bit_pos;
> > }
> > } else {
> > - pr_err("invalid bit-flip @ %d:%d\n",
> > - byte_pos, bit_pos);
> > + dev_err(&info->pdev->dev,
> > + "invalid bit-flip @ %d:%d\n",
> > + byte_pos, bit_pos);
> > err = -EBADMSG;
> > }
> > }
> > @@ -1598,13 +1600,13 @@ static bool is_elm_present(struct omap_nand_info *info,
> >
> > /* check whether elm-id is passed via DT */
> > if (!elm_node) {
> > - pr_err("nand: error: ELM DT node not found\n");
> > + dev_err(&info->pdev->dev, "ELM devicetree node not found\n");
> > return false;
> > }
> > pdev = of_find_device_by_node(elm_node);
> > /* check whether ELM device is registered */
> > if (!pdev) {
> > - pr_err("nand: error: ELM device not found\n");
> > + dev_err(&info->pdev->dev, "ELM device not found\n");
> > return false;
> > }
> > /* ELM module available, now configure it */
> > @@ -1734,14 +1736,14 @@ static int omap_nand_probe(struct platform_device *pdev)
> > /* scan NAND device connected to chip controller */
> > nand_chip->options |= pdata->devsize & NAND_BUSWIDTH_16;
> > if (nand_scan_ident(mtd, 1, NULL)) {
> > - pr_err("nand device scan failed, may be bus-width mismatch\n");
> > + dev_err(&info->pdev->dev, "scan failed, may be bus-width mismatch\n");
> > err = -ENXIO;
> > goto return_error;
> > }
> >
> > /* check for small page devices */
> > if ((mtd->oobsize < 64) && (pdata->ecc_opt != OMAP_ECC_HAM1_CODE_HW)) {
> > - pr_err("small page devices are not supported\n");
> > + dev_err(&info->pdev->dev, "small page devices are not supported\n");
> > err = -EINVAL;
> > goto return_error;
> > }
> > @@ -1959,7 +1961,6 @@ static int omap_nand_probe(struct platform_device *pdev)
> > nand_chip->ecc.bytes,
> > &ecclayout);
> > if (!nand_chip->ecc.priv) {
> > - pr_err("nand: error: unable to use s/w BCH library\n");
>
> Where would the error be printed in this case?
>
Well, nand_bch_init() has a lot of messages for the errors, but I just noticed
some cases where there's no message printed. Would you prefer to leave these
untouched?
> I also noticed a similar message in the OMAP_ECC_BCH4_CODE_HW_DETECTION_SW case.
> And it seems to be missing a "goto return_error" there.
>
Argh, right. I'll have to resend this one.
--
Ezequiel Garcia, VanguardiaSur
www.vanguardiasur.com.ar
More information about the linux-mtd
mailing list