[PATCH v2] mtd: nand: Fix problem with NAND_CMD_RNDOUT (05h-E0h)

[Brian Norris]

Hi Pekon,

On Tue, May 06, 2014 at 03:58:40PM +0530, Pekon Gupta wrote:
> From: Bacem Daassi <Bacem.Daassi at spansion.com>
> 
> Though the NAND_CMD_READ "Page Read" command expects the full address footprint
> (2bytes for column address + 3bytes for row address).
> But once the page is loaded into the read buffer, NAND_CMD_RNDOUT (05h-E0h) also
> called "Random Data Output" command expects to see only the column address that
> should be addressed within the already loaded page present in read buffers.
> Only 2 address cycles with ALE active should be provided between the 05h and E0h
> So expected sequence for NAND_CMD_RNDOUT is
> 	<05h> <column-addr-byte1> <column-address-byte2> <E0h>
> 
> Though most NAND Devices mentioned above tend to work even if extra cycles of
> page-address is issued between <05h> .... <E0h> command. But some Spansion and
> Hynix devices break on this non-compliance.
> The same issue has been reported by Bacem Daassi
>   http://e2e.ti.com/support/arm/sitara_arm/f/791/t/259699.aspx
> 
> This patch fixes nand_command for all vendors devices as datasheet of all
> devices expect same sequence.
> 
> +--------+------------------------+---------------------------------------------
> |Vendor  | Datasheet/Part#        |  Reference
> +--------+------------------------+---------------------------------------------
> |Spansion| S34ML{01|02|04}G2      | Figure 6.12 Random Data Output In a Page
> |Micron  | MT29F{16|32|64|128}G08A| Figure 47: CHANGE READ COLUMN (05h-E0h) Operation
> |Macronix| MX30LF1G08AA           | Figure 10. AC Waveforms for Random Data Output
> |Toshiba | TC58NVG1S3ETAI0        | Figure Column Address Change in Read Cycle Timing Diagram (2/2)
> +--------+------------------------+---------------------------------------------
> 
> Reported-by: Bacem Daassi <Bacem.Daassi at spansion.com>
> Reported-by: Marek Belisko <marek.belisko at gmail.com>
> Reported-by: Steven Kipisz <s-kipisz2 at ti.com>
> Signed-off-by: Pekon Gupta <pekon at ti.com>
> ---
> changes v1->v2:  fixed both nand_command() and nand_command_lp()
> 
>  drivers/mtd/nand/nand_base.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
> index 9d01c4d..c11565f 100644
> --- a/drivers/mtd/nand/nand_base.c
> +++ b/drivers/mtd/nand/nand_base.c
> @@ -595,7 +595,7 @@ static void nand_command(struct mtd_info *mtd, unsigned int command,
>  		chip->cmd_ctrl(mtd, column, ctrl);
>  		ctrl &= ~NAND_CTRL_CHANGE;
>  	}
> -	if (page_addr != -1) {
> +	if (page_addr != -1 && command != NAND_CMD_RNDOUT) {
>  		chip->cmd_ctrl(mtd, page_addr, ctrl);
>  		ctrl &= ~NAND_CTRL_CHANGE;
>  		chip->cmd_ctrl(mtd, page_addr >> 8, ctrl);
> @@ -688,7 +688,7 @@ static void nand_command_lp(struct mtd_info *mtd, unsigned int command,
>  			ctrl &= ~NAND_CTRL_CHANGE;
>  			chip->cmd_ctrl(mtd, column >> 8, ctrl);
>  		}
> -		if (page_addr != -1) {
> +		if (page_addr != -1 && command != NAND_CMD_RNDOUT) {
>  			chip->cmd_ctrl(mtd, page_addr, ctrl);
>  			chip->cmd_ctrl(mtd, page_addr >> 8,
>  				       NAND_NCE | NAND_ALE);

I do not think this change is necessary at all. This already works just
fine if drivers use the cmdfunc() interface appropriately. That is, if
they always use page_addr = -1 for NAND_CMD_RNDOUT, like:

	chip->cmdfunc(mtd, NAND_CMD_RNDOUT, col, -1);

As I see it, all users in mainline do this. So is somebody trying to
push an unneeded patch upstream, where the real problem is with their
out-of-tree driver?

Unless you can convince me otherwise, I'll give this patch a NAK.

Regards,
Brian