[PATCH v6 22/36] mtd: st_spi_fsm: Supply the N25Qxxx specific read configurations
Lee Jones
lee.jones at linaro.org
Thu Mar 20 05:20:54 EDT 2014
The N25Qxxx Serial Flash devices required different sequence
configurations depending on whether they're running in 24bit (3Byte)
or 32bit (4Byte) mode. We provide those here.
Acked-by Angus Clark <angus.clark at st.com>
Signed-off-by: Lee Jones <lee.jones at linaro.org>
---
drivers/mtd/devices/st_spi_fsm.c | 91 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 91 insertions(+)
diff --git a/drivers/mtd/devices/st_spi_fsm.c b/drivers/mtd/devices/st_spi_fsm.c
index 03b49a4..c902d5b 100644
--- a/drivers/mtd/devices/st_spi_fsm.c
+++ b/drivers/mtd/devices/st_spi_fsm.c
@@ -200,6 +200,53 @@
#define STFSM_MAX_WAIT_SEQ_MS 1000 /* FSM execution time */
+/* Flash Commands */
+#define FLASH_CMD_WREN 0x06
+#define FLASH_CMD_WRDI 0x04
+#define FLASH_CMD_RDID 0x9f
+#define FLASH_CMD_RDSR 0x05
+#define FLASH_CMD_RDSR2 0x35
+#define FLASH_CMD_WRSR 0x01
+#define FLASH_CMD_SE_4K 0x20
+#define FLASH_CMD_SE_32K 0x52
+#define FLASH_CMD_SE 0xd8
+#define FLASH_CMD_CHIPERASE 0xc7
+#define FLASH_CMD_WRVCR 0x81
+#define FLASH_CMD_RDVCR 0x85
+
+#define FLASH_CMD_READ 0x03 /* READ */
+#define FLASH_CMD_READ_FAST 0x0b /* FAST READ */
+#define FLASH_CMD_READ_1_1_2 0x3b /* DUAL OUTPUT READ */
+#define FLASH_CMD_READ_1_2_2 0xbb /* DUAL I/O READ */
+#define FLASH_CMD_READ_1_1_4 0x6b /* QUAD OUTPUT READ */
+#define FLASH_CMD_READ_1_4_4 0xeb /* QUAD I/O READ */
+
+#define FLASH_CMD_WRITE 0x02 /* PAGE PROGRAM */
+#define FLASH_CMD_WRITE_1_1_2 0xa2 /* DUAL INPUT PROGRAM */
+#define FLASH_CMD_WRITE_1_2_2 0xd2 /* DUAL INPUT EXT PROGRAM */
+#define FLASH_CMD_WRITE_1_1_4 0x32 /* QUAD INPUT PROGRAM */
+#define FLASH_CMD_WRITE_1_4_4 0x12 /* QUAD INPUT EXT PROGRAM */
+
+#define FLASH_CMD_EN4B_ADDR 0xb7 /* Enter 4-byte address mode */
+#define FLASH_CMD_EX4B_ADDR 0xe9 /* Exit 4-byte address mode */
+
+/* READ commands with 32-bit addressing (N25Q256 and S25FLxxxS) */
+#define FLASH_CMD_READ4 0x13
+#define FLASH_CMD_READ4_FAST 0x0c
+#define FLASH_CMD_READ4_1_1_2 0x3c
+#define FLASH_CMD_READ4_1_2_2 0xbc
+#define FLASH_CMD_READ4_1_1_4 0x6c
+#define FLASH_CMD_READ4_1_4_4 0xec
+
+/*
+ * Flags to tweak operation of default read/write/erase routines
+ */
+#define CFG_READ_TOGGLE_32BIT_ADDR 0x00000001
+#define CFG_WRITE_TOGGLE_32BIT_ADDR 0x00000002
+#define CFG_WRITE_EX_32BIT_ADDR_DELAY 0x00000004
+#define CFG_ERASESEC_TOGGLE_32BIT_ADDR 0x00000008
+#define CFG_S25FL_CHECK_ERROR_FLAGS 0x00000010
+
struct stfsm {
struct device *dev;
void __iomem *base;
@@ -208,6 +255,7 @@ struct stfsm {
struct mutex lock;
struct flash_info *info;
+ uint32_t configuration;
uint32_t fifo_dir_delay;
bool booted_from_spi;
bool reset_signal;
@@ -402,6 +450,49 @@ static struct seq_rw_config default_write_configs[] = {
{0x00, 0, 0, 0, 0, 0x00, 0, 0},
};
+/*
+ * [N25Qxxx] Configuration
+ */
+#define N25Q_VCR_DUMMY_CYCLES(x) (((x) & 0xf) << 4)
+#define N25Q_VCR_XIP_DISABLED ((uint8_t)0x1 << 3)
+#define N25Q_VCR_WRAP_CONT 0x3
+
+/* N25Q 3-byte Address READ configurations
+ * - 'FAST' variants configured for 8 dummy cycles.
+ *
+ * Note, the number of dummy cycles used for 'FAST' READ operations is
+ * configurable and would normally be tuned according to the READ command and
+ * operating frequency. However, this applies universally to all 'FAST' READ
+ * commands, including those used by the SPIBoot controller, and remains in
+ * force until the device is power-cycled. Since the SPIBoot controller is
+ * hard-wired to use 8 dummy cycles, we must configure the device to also use 8
+ * cycles.
+ */
+static struct seq_rw_config n25q_read3_configs[] = {
+ {FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ_1_4_4, 0, 4, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ_1_1_4, 0, 1, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ_1_2_2, 0, 2, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ_1_1_2, 0, 1, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_FAST, FLASH_CMD_READ_FAST, 0, 1, 1, 0x00, 0, 8},
+ {FLASH_FLAG_READ_WRITE, FLASH_CMD_READ, 0, 1, 1, 0x00, 0, 0},
+ {0x00, 0, 0, 0, 0, 0x00, 0, 0},
+};
+
+/* N25Q 4-byte Address READ configurations
+ * - use special 4-byte address READ commands (reduces overheads, and
+ * reduces risk of hitting watchdog reset issues).
+ * - 'FAST' variants configured for 8 dummy cycles (see note above.)
+ */
+static struct seq_rw_config n25q_read4_configs[] = {
+ {FLASH_FLAG_READ_1_4_4, FLASH_CMD_READ4_1_4_4, 0, 4, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_4, FLASH_CMD_READ4_1_1_4, 0, 1, 4, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_2_2, FLASH_CMD_READ4_1_2_2, 0, 2, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_1_1_2, FLASH_CMD_READ4_1_1_2, 0, 1, 2, 0x00, 0, 8},
+ {FLASH_FLAG_READ_FAST, FLASH_CMD_READ4_FAST, 0, 1, 1, 0x00, 0, 8},
+ {FLASH_FLAG_READ_WRITE, FLASH_CMD_READ4, 0, 1, 1, 0x00, 0, 0},
+ {0x00, 0, 0, 0, 0, 0x00, 0, 0},
+};
+
static struct stfsm_seq stfsm_seq_en_32bit_addr;/* Dynamically populated */
static struct stfsm_seq stfsm_seq_read_jedec = {
--
1.8.3.2
More information about the linux-mtd
mailing list