[PATCH 00/36] OMAP: GPMC: Restructure and move OMAP GPMC driver out of mach-omap2
Javier Martinez Canillas
javier at dowhile0.org
Wed Jun 11 04:52:07 PDT 2014
Hello Roger,
What a great series!!
On Wed, Jun 11, 2014 at 10:56 AM, Roger Quadros <rogerq at ti.com> wrote:
> Hi,
>
> This is a complete functional set to get the gpmc driver out of mach-omap2
> and into drivers/memory. The DT binding remains the same except for the
> following minor changes
I probably won't have time to do a proper review until at least next
week but doing a quick glance it looks very good to me.
> - compatible property is required for NAND & OneNAND nodes
This is a minor ABI breakage but I agree with you that it is wrong
that these were not introduced in the first place and relied on the
dev node so I think is not that bad to break it in this case.
> - Second register space and interrupts properties are required for
> NAND controller node
> - ti,onenand-sync-rw property added for OneNAND node.
>
> The series does the following changes
> - Move GPMC IRQ and NAND register handling to NAND driver.
> The entire GPMC register space is made available to the NAND driver.
> - Clean up NAND device tree handling. Don't rely on legacy platform device
> i.e. don't call gpmc_nand_init()
> - Add 2 public APIs omap_gpmc_retime() and omap_gpmc_get_clk_period()
> omap_gpmc_retime() allows to reconfigure the GPMC settings and timings
> for the specified Chip select region.
> omap_gpmc_get_clk_period() allows to query the GPMC_CLK (external clock)
> period, to perform timing calculations.
> Both functions will be needed by the OneNAND driver since it calculates
> device timings on the fly and needs to change from Asynchronous mode
> to Synchronous mode.
> - Setup OneNAND in Asynchronous mode by default and move Synchronous
> setting code into OneNAND driver.
> - Clean up OneNAND device tree handling. Don't rely on legacy platform device
> i.e. don't call gpmc_onenand_init()
> - Introduce gpmc_generic_init() that should be used by board files to specify
> GPMC chip select setting/timing and platform device within that Chip Select.
> - Stop using all gpmc*() that are meant to be private to GPMC driver.
> - Move GPMC driver into drivers/memory
>
> Tested on:
>
> - beagleboard C4: NAND
> - Nokia N900: OneNAND
>
Do you have a tree somewhere that I can use it to test on the boards I
maintain and post patches to update the DTS according the new binding?
> Changelog:
>
> [1] RFC patch - https://lkml.org/lkml/2014/5/21/218
>
> cheers,
> -roger
>
> ---
> Roger Quadros (36):
> ARM: OMAP3: hwmod: Fix gpmc memory resource space
> ARM: dts: OMAP2+: Fix GPMC register space size
> ARM: OMAP2+: gpmc: Add platform data
> ARM: OMAP2+: gpmc: Add gpmc timings and settings to platform data
> mtd: nand: omap: Move IRQ handling from GPMC to NAND driver
> mtd: nand: omap: Move gpmc_update_nand_reg to nand driver
> mtd: nand: omap: Move NAND write protect code from GPMC to NAND driver
> mtd: nand: omap: Copy platform data parameters to omap_nand_info data
> mtd: nand: omap: Clean up device tree support
> ARM: dts: OMAP2+: Fix NAND device nodes
> mtd: nand: omap: Update DT binding documentation
> ARM: dts: omap3-beagle: Add NAND device
> ARM: OMAP2+: gpmc.c: sanity check bank-width DT property
> ARM: OMAP2+: gpmc: Allow drivers to reconfigure GPMC settings &
> timings
> ARM: OMAP2+: gpmc: Allow drivers to query GPMC_CLK period
> mtd: onenand: omap: Remove regulator management code
> ARM: OMAP2+: gpmc-onenand: Use Async settings/timings by default
> ARM: OMAP2+: gpmc-onenand: Move Synchronous setting code to drivers/
> mtd: onenand: omap: Use devres managed resources
> mtd: onenand: omap: Clean up device tree support
> ARM: dts: OMAP2+: Fix OneNAND device nodes
> ARM: OMAP2+: gmpc: add gpmc_generic_init()
> ARM: OMAP2+: gpmc: use platform data to configure CS space and
> poplulate device
> ARM: OMAP2+: gpmc: add NAND specific setup
> ARM: OMAP2+: gpmc: Support multiple Chip Selects per device
> ARM: OMAP2+: gpmc-smc91x: Get rid of retime() from
> omap_smc91x_platform_data
> ARM: OMAP2+: usb-tusb6010: Use omap_gpmc_retime()
> ARM: OMAP2+: nand: Update gpmc_nand_init() to use generic_gpmc_init()
> ARM: OMAP2+: gpmc-smc91x: Use gpmc_generic_init()
> ARM: OMAP2+: gpmc-smsc911x: Use gpmc_generic_init()
> ARM: OMAP2: usb-tusb6010: Use gpmc_generic_init()
> ARM: OMAP2+: onenand: Use gpmc_generic_init()
> ARM: OMAP2+: board-flash: Use gpmc_generic_init() for NOR
> ARM: OMAP2+: gpmc: Make externally unused functions/defines private
> ARM: OMAP2+: gpmc: move GPMC driver into drivers/memory
> ARM: OMAP2+: defconfig: Enable TI GPMC driver
>
> .../devicetree/bindings/mtd/gpmc-nand.txt | 16 +-
> .../devicetree/bindings/mtd/gpmc-onenand.txt | 4 +
> arch/arm/boot/dts/am335x-evm.dts | 8 +-
> arch/arm/boot/dts/am335x-igep0033.dtsi | 8 +-
> arch/arm/boot/dts/am33xx.dtsi | 2 +-
> arch/arm/boot/dts/am4372.dtsi | 2 +-
> arch/arm/boot/dts/am43x-epos-evm.dts | 8 +-
> arch/arm/boot/dts/omap2420-n8x0-common.dtsi | 5 +-
> arch/arm/boot/dts/omap2420.dtsi | 2 +-
> arch/arm/boot/dts/omap2430.dtsi | 2 +-
> arch/arm/boot/dts/omap3-beagle.dts | 53 +
> arch/arm/boot/dts/omap3-devkit8000.dts | 9 +-
> arch/arm/boot/dts/omap3-evm-37xx.dts | 10 +-
> arch/arm/boot/dts/omap3-igep0020.dts | 10 +-
> arch/arm/boot/dts/omap3-igep0030.dts | 8 +-
> arch/arm/boot/dts/omap3-ldp.dts | 10 +-
> arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 10 +-
> arch/arm/boot/dts/omap3-lilly-dbb056.dts | 7 +-
> arch/arm/boot/dts/omap3-n900.dts | 6 +-
> arch/arm/boot/dts/omap3-n950-n9.dtsi | 6 +-
> arch/arm/boot/dts/omap3.dtsi | 2 +-
> arch/arm/boot/dts/omap3430-sdp.dts | 14 +-
> arch/arm/boot/dts/omap4.dtsi | 2 +-
> arch/arm/boot/dts/omap5.dtsi | 2 +-
> arch/arm/configs/omap2plus_defconfig | 2 +
> arch/arm/mach-omap2/Makefile | 2 +-
> arch/arm/mach-omap2/board-3430sdp.c | 8 +-
> arch/arm/mach-omap2/board-flash.c | 28 +-
> arch/arm/mach-omap2/gpmc-nand.c | 66 +-
> arch/arm/mach-omap2/gpmc-onenand.c | 351 +---
> arch/arm/mach-omap2/gpmc-smc91x.c | 91 +-
> arch/arm/mach-omap2/gpmc-smc91x.h | 1 -
> arch/arm/mach-omap2/gpmc-smsc911x.c | 76 +-
> arch/arm/mach-omap2/gpmc.c | 1872 --------------------
> arch/arm/mach-omap2/gpmc.h | 221 +--
> arch/arm/mach-omap2/gpmc_legacy.c | 296 ++++
> arch/arm/mach-omap2/omap_hwmod_3xxx_data.c | 2 +-
> arch/arm/mach-omap2/usb-tusb6010.c | 172 +-
> drivers/memory/Kconfig | 10 +
> drivers/memory/Makefile | 1 +
> drivers/memory/ti-gpmc.c | 1829 +++++++++++++++++++
> drivers/mtd/nand/Kconfig | 2 +-
> drivers/mtd/nand/omap2.c | 364 +++-
> drivers/mtd/onenand/Kconfig | 6 +-
> drivers/mtd/onenand/omap2.c | 456 +++--
> include/linux/platform_data/gpmc-omap.h | 189 ++
> include/linux/platform_data/mtd-nand-omap2.h | 10 +-
> include/linux/platform_data/mtd-onenand-omap2.h | 7 +-
> 48 files changed, 3361 insertions(+), 2907 deletions(-)
> delete mode 100644 arch/arm/mach-omap2/gpmc.c
> create mode 100644 arch/arm/mach-omap2/gpmc_legacy.c
> create mode 100644 drivers/memory/ti-gpmc.c
> create mode 100644 include/linux/platform_data/gpmc-omap.h
>
> --
> 1.8.3.2
>
Best regards,
Javier
More information about the linux-mtd
mailing list