[PATCH 1/1] ubi: Introduce block devices for UBI volumes

[Ezequiel Garcia]

On Tue, Feb 04, 2014 at 08:06:43AM -0300, Ezequiel Garcia wrote:
> On Fri, Jan 31, 2014 at 06:06:37PM +0100, Willy Tarreau wrote:
> > On Wed, Jan 29, 2014 at 05:38:01PM -0300, Ezequiel Garcia wrote:
> > > Block device emulation on top of ubi volumes with cached read/write support.
> > > Both the cached access and the write support are selectable at compile time.
> > > 
> > > Given UBI takes care of wear leveling and bad block management it's possible
> > > to add a thin layer to enable block device access to UBI volumes.
> > > This allows to use a block-oriented filesystem on a flash device.
> > > 
> > > In a similar fashion to mtdblock, a 1-LEB size cache has been
> > > implemented. However, very memory-constrained systems can choose to
> > > disable the cache and save the 1-LEB byte allocation.
> > > 
> > > If write support is enabled, the flash device will be written when the cache
> > > is flushed. The following events trigger this:
> > > * block device release (detach)
> > > * different than cached leb is accessed
> > > * io-barrier is received through a REQ_FLUSH request
> > > 
> > > Despite this efforts, it's very important to remember that regular
> > > block-oriented filesystems have no care at all about wear leveling;
> > > they will access the block device randomly, only caring for performance.
> > > Therefore, write support should be selected only for development and
> > > with extreme caution.
> > > 
> > > The cache is 1-LEB bytes, vmalloced at open() and freed at release();
> > > in addition, each block device has a workqueue associated.
> > > 
> > > Block devices are created upon user request through new ioctls:
> > > UBI_IOCVOLATTBLK to attach and UBI_IOCVOLDETBLK to detach.
> > > Also, a new UBI module parameter is added 'ubi.block'. This parameter is
> > > needed in order to attach a block device on boot-up time, allowing to
> > > mount the rootfs on a ubiblock device.
> > > For instance, you could have these kernel parameters:
> > > 
> > >   ubi.mtd=5 ubi.block=0,0 root=/dev/ubiblock0_0
> > > 
> > > Or, if you compile ubi as a module:
> > > 
> > >   $ modprobe ubi mtd=/dev/mtd5 block=/dev/ubi0_0
> > > 
> > > Cc: Artem Bityutskiy <dedekind1 at gmail.com>
> > > Cc: David Woodhouse <dwmw2 at infradead.org>
> > > Cc: Brian Norris <computersforpeace at gmail.com>
> > > Cc: Michael Opdenacker <michael.opdenacker at free-electrons.com>
> > > Cc: Tim Bird <tim.bird at am.sony.com>
> > > Cc: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
> > > Cc: Mike Frysinger <vapier at gentoo.org>
> > > Cc: Piergiorgio Beruto <piergiorgio.beruto at gmail.com>
> > > Cc: Willy Tarreau <w at 1wt.eu>
> > > Signed-off-by: Ezequiel Garcia <ezequiel.garcia at free-electrons.com>
> > 
> > Works pretty well here on 3.14-git. I've also tested write support
> > with success. I'm booting from a squashfs installed on top of it.
> > I find that the combination of squashfs + ubiblock is really good
> > for a rootfs. It's fast, space-efficient in terms of RAM and NAND,
> > and made reliable by the ubi layer.
> > 
> > Concerning the question about the usage of write support, I find it
> > useful to perform rootfs upgrades from Linux.
> > 
> > Feel free to add :
> > 
> >    Tested-By: Willy Tarreau <w at 1wt.eu>
> > 
> 
> Thanks Willy!
> 
> Artem: If at all possible, I'd like to avoid stalling, so feel free to comment
> on anything...

Ping?

-- 
Ezequiel García, Free Electrons
Embedded Linux, Kernel and Android Engineering
http://free-electrons.com