[V7 PATCH 1/1] driver:mtd:spi-nor: Add quad I/O support for Micron spi nor
Bean Huo 霍斌斌 (beanhuo)
beanhuo at micron.com
Tue Dec 16 23:35:45 PST 2014
This patch adds code which enables Quad I/O mode on Micron SPI NOR flashes.
For Micron SPI NOR flash, enabling or disabling quad I/O protocol can be done
By two methods, which are to use EVCR(Enhanced Volatile Configuration Register)
and the ENTER QUAD I/O MODE command. There is no difference between these two
methods. Unfortunately, for some Micron spi nor flashes, there no ENTER Quad I/O
command(35h),such as n25q064.But for all current Micron spi nor, if it support
quad I/O mode, using EVCR definitely be supported. It is a recommended method to
enable Quad I/O mode by EVCR, Quad I/O protocol bit 7.When EVCR bit 7 is reset
to 0,the SPI NOR flash will operate in quad I/O mode.
This patch has been tested on N25Q512A and MT25TL256BAA1ESF.Micron spi nor of
spi_nor_ids[] table all support this method.
Signed-off-by: bean huo <beanhuo at micron.com>
Acked-by: Marek Vasut <marex at denx.de>
---
v1-v2:
Modified to that capture wait_till_ready()
return value,if error,directly return its
the value.
v2-v3:
Directly use the reurning error value of
read_reg and write_reg,instead of -EINVAL.
v3-v4:
Modify commit logs that wraped into 80 columns.
v4-v5:
Rebuild new patch based on latest linux-mtd.
v5-v6:
Rebuild patch based on latest l2-mtd.
add some comments.
Add SPI_NOR_QUAD_READ flag in the spi_nor_ids[] for Micron spi nor.
V6-v7:
Fixed up val with u8 in micron_quad_enable().
drivers/mtd/spi-nor/spi-nor.c | 62 +++++++++++++++++++++++++++++++++++------
include/linux/mtd/spi-nor.h | 7 +++++
2 files changed, 61 insertions(+), 8 deletions(-)
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 0f8ec3c..ea196c1 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -560,14 +560,14 @@ static const struct spi_device_id spi_nor_ids[] = {
{ "mx66l1g55g", INFO(0xc2261b, 0, 64 * 1024, 2048, SPI_NOR_QUAD_READ) },
/* Micron */
- { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) },
- { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) },
- { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) },
- { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) },
- { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) },
- { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) },
- { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, USE_FSR) },
- { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, USE_FSR) },
+ { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, SPI_NOR_QUAD_READ) },
+ { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, SPI_NOR_QUAD_READ) },
+ { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, SPI_NOR_QUAD_READ) },
+ { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, SPI_NOR_QUAD_READ) },
+ { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_QUAD_READ) },
+ { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
+ { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
/* PMC */
{ "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) },
@@ -891,6 +891,45 @@ static int spansion_quad_enable(struct spi_nor *nor)
return 0;
}
+static int micron_quad_enable(struct spi_nor *nor)
+{
+ int ret;
+ u8 val;
+
+ ret = nor->read_reg(nor, SPINOR_OP_RD_EVCR, &val, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error %d reading EVCR\n", ret);
+ return ret;
+ }
+
+ write_enable(nor);
+
+ /* set EVCR, enable quad I/O */
+ nor->cmd_buf[0] = val & ~EVCR_QUAD_EN_MICRON;
+ ret = nor->write_reg(nor, SPINOR_OP_WD_EVCR, nor->cmd_buf, 1, 0);
+ if (ret < 0) {
+ dev_err(nor->dev, "error while writing EVCR register\n");
+ return ret;
+ }
+
+ ret = spi_nor_wait_till_ready(nor);
+ if (ret)
+ return ret;
+
+ /* read EVCR and check it */
+ ret = nor->read_reg(nor, SPINOR_OP_RD_EVCR, &val, 1);
+ if (ret < 0) {
+ dev_err(nor->dev, "error %d reading EVCR\n", ret);
+ return ret;
+ }
+ if (val & EVCR_QUAD_EN_MICRON) {
+ dev_err(nor->dev, "Micron EVCR Quad bit not clear\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
static int set_quad_mode(struct spi_nor *nor, struct flash_info *info)
{
int status;
@@ -903,6 +942,13 @@ static int set_quad_mode(struct spi_nor *nor, struct flash_info *info)
return -EINVAL;
}
return status;
+ case CFI_MFR_ST:
+ status = micron_quad_enable(nor);
+ if (status) {
+ dev_err(nor->dev, "Micron quad-read not enabled\n");
+ return -EINVAL;
+ }
+ return status;
default:
status = spansion_quad_enable(nor);
if (status) {
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 63aeccf..4720b86 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -56,6 +56,10 @@
/* Used for Spansion flashes only. */
#define SPINOR_OP_BRWR 0x17 /* Bank register write */
+/* Used for Micron flashes only. */
+#define SPINOR_OP_RD_EVCR 0x65 /* Read EVCR register */
+#define SPINOR_OP_WD_EVCR 0x61 /* Write EVCR register */
+
/* Status Register bits. */
#define SR_WIP 1 /* Write in progress */
#define SR_WEL 2 /* Write enable latch */
@@ -67,6 +71,9 @@
#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */
+/* Enhanced Volatile Configuration Register bits */
+#define EVCR_QUAD_EN_MICRON 0x80 /* Micron Quad I/O */
+
/* Flag Status Register bits */
#define FSR_READY 0x80
--
1.7.9.5
More information about the linux-mtd
mailing list