[PATCH 2/3] mtd: spi-nor: remove the jedec_id/ext_id
Huang Shijie
shijie.huang at intel.com
Mon Aug 11 17:54:55 PDT 2014
The "id" array contains all the information about the JEDEC and the
manufacturer ID info, this patch remove the jedec_id/ext_id from the
flash_info.
Signed-off-by: Huang Shijie <shijie.huang at intel.com>
---
drivers/mtd/spi-nor/spi-nor.c | 98 +++++++++++++++++++----------------------
1 files changed, 45 insertions(+), 53 deletions(-)
diff --git a/drivers/mtd/spi-nor/spi-nor.c b/drivers/mtd/spi-nor/spi-nor.c
index 0b69072..a0923b0 100644
--- a/drivers/mtd/spi-nor/spi-nor.c
+++ b/drivers/mtd/spi-nor/spi-nor.c
@@ -26,7 +26,38 @@
/* Define max times to check status register before we give up. */
#define MAX_READY_WAIT_JIFFIES (40 * HZ) /* M25P16 specs 40s max chip erase */
-#define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16)
+#define SPI_NOR_MAX_ID_LEN 6
+
+struct flash_info {
+ /*
+ * This array stores the ID bytes.
+ * The first three bytes are the JEDIC id.
+ * JEDEC id zero means "no ID" (most older chips);
+ */
+ u8 id[SPI_NOR_MAX_ID_LEN];
+ u8 id_len;
+
+ /* The size listed here is what works with SPINOR_OP_SE, which isn't
+ * necessarily called a "sector" by the vendor.
+ */
+ unsigned sector_size;
+ u16 n_sectors;
+
+ u16 page_size;
+ u16 addr_width;
+
+ u16 flags;
+#define SECT_4K 0x01 /* SPINOR_OP_BE_4K works uniformly */
+#define SPI_NOR_NO_ERASE 0x02 /* No erase command needed */
+#define SST_WRITE 0x04 /* use SST byte programming */
+#define SPI_NOR_NO_FR 0x08 /* Can't do fastread */
+#define SECT_4K_PMC 0x10 /* SPINOR_OP_BE_4K_PMC works uniformly */
+#define SPI_NOR_DUAL_READ 0x20 /* Flash supports Dual Read */
+#define SPI_NOR_QUAD_READ 0x40 /* Flash supports Quad Read */
+#define USE_FSR 0x80 /* use flag status register */
+};
+
+#define JEDEC_MFR(info) ((info)->id[0])
/*
* Read the status register, returning its value in the location
@@ -136,13 +167,14 @@ static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd)
}
/* Enable/disable 4-byte addressing mode. */
-static inline int set_4byte(struct spi_nor *nor, u32 jedec_id, int enable)
+static inline int
+set_4byte(struct spi_nor *nor, struct flash_info *info, int enable)
{
int status;
bool need_wren = false;
u8 cmd;
- switch (JEDEC_MFR(jedec_id)) {
+ switch (JEDEC_MFR(info)) {
case CFI_MFR_ST: /* Micron, actually */
/* Some Micron need WREN command; all will accept it */
need_wren = true;
@@ -422,49 +454,9 @@ err:
return ret;
}
-#define SPI_NOR_MAX_ID_LEN 6
-
-struct flash_info {
- /* JEDEC id zero means "no ID" (most older chips); otherwise it has
- * a high byte of zero plus three data bytes: the manufacturer id,
- * then a two byte device id.
- */
- u32 jedec_id;
- u16 ext_id;
-
- /*
- * This array stores the ID bytes.
- * The first three bytes are the JEDIC id.
- * JEDEC id zero means "no ID" (most older chips);
- */
- u8 id[SPI_NOR_MAX_ID_LEN];
- u8 id_len;
-
- /* The size listed here is what works with SPINOR_OP_SE, which isn't
- * necessarily called a "sector" by the vendor.
- */
- unsigned sector_size;
- u16 n_sectors;
-
- u16 page_size;
- u16 addr_width;
-
- u16 flags;
-#define SECT_4K 0x01 /* SPINOR_OP_BE_4K works uniformly */
-#define SPI_NOR_NO_ERASE 0x02 /* No erase command needed */
-#define SST_WRITE 0x04 /* use SST byte programming */
-#define SPI_NOR_NO_FR 0x08 /* Can't do fastread */
-#define SECT_4K_PMC 0x10 /* SPINOR_OP_BE_4K_PMC works uniformly */
-#define SPI_NOR_DUAL_READ 0x20 /* Flash supports Dual Read */
-#define SPI_NOR_QUAD_READ 0x40 /* Flash supports Quad Read */
-#define USE_FSR 0x80 /* use flag status register */
-};
-
/* Used when the "_ext_id" is two bytes at most */
#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \
((kernel_ulong_t)&(struct flash_info) { \
- .jedec_id = (_jedec_id), \
- .ext_id = (_ext_id), \
.id = { \
((_jedec_id) >> 16) & 0xff, \
((_jedec_id) >> 8) & 0xff, \
@@ -889,11 +881,11 @@ static int spansion_quad_enable(struct spi_nor *nor)
return 0;
}
-static int set_quad_mode(struct spi_nor *nor, u32 jedec_id)
+static int set_quad_mode(struct spi_nor *nor, struct flash_info *info)
{
int status;
- switch (JEDEC_MFR(jedec_id)) {
+ switch (JEDEC_MFR(info)) {
case CFI_MFR_MACRONIX:
status = macronix_quad_enable(nor);
if (status) {
@@ -966,7 +958,7 @@ int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id,
info = (void *)id->driver_data;
- if (info->jedec_id) {
+ if (info->id_len) {
const struct spi_device_id *jid;
jid = jedec_probe(nor);
@@ -994,9 +986,9 @@ int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id,
* up with the software protection bits set
*/
- if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL ||
- JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL ||
- JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) {
+ if (JEDEC_MFR(info) == CFI_MFR_ATMEL ||
+ JEDEC_MFR(info) == CFI_MFR_INTEL ||
+ JEDEC_MFR(info) == CFI_MFR_SST) {
write_enable(nor);
write_sr(nor, 0);
}
@@ -1014,7 +1006,7 @@ int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id,
mtd->_read = spi_nor_read;
/* nor protection support for STmicro chips */
- if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ST) {
+ if (JEDEC_MFR(info) == CFI_MFR_ST) {
mtd->_lock = spi_nor_lock;
mtd->_unlock = spi_nor_unlock;
}
@@ -1065,7 +1057,7 @@ int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id,
/* Quad/Dual-read mode takes precedence over fast/normal */
if (mode == SPI_NOR_QUAD && info->flags & SPI_NOR_QUAD_READ) {
- ret = set_quad_mode(nor, info->jedec_id);
+ ret = set_quad_mode(nor, info);
if (ret) {
dev_err(dev, "quad mode not supported\n");
return ret;
@@ -1101,7 +1093,7 @@ int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id,
else if (mtd->size > 0x1000000) {
/* enable 4-byte addressing if the device exceeds 16MiB */
nor->addr_width = 4;
- if (JEDEC_MFR(info->jedec_id) == CFI_MFR_AMD) {
+ if (JEDEC_MFR(info) == CFI_MFR_AMD) {
/* Dedicated 4-byte command set */
switch (nor->flash_read) {
case SPI_NOR_QUAD:
@@ -1122,7 +1114,7 @@ int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id,
nor->erase_opcode = SPINOR_OP_SE_4B;
mtd->erasesize = info->sector_size;
} else
- set_4byte(nor, info->jedec_id, 1);
+ set_4byte(nor, info, 1);
} else {
nor->addr_width = 3;
}
--
1.7.7.6
More information about the linux-mtd
mailing list