[PATCH v4] drivers: mtd: m25p80: add quad read support

Sourav Poddar sourav.poddar at ti.com
Mon Nov 11 00:28:05 EST 2013


Hi Brian,
On Saturday 09 November 2013 12:07 AM, Brian Norris wrote:
> From: Sourav Poddar<sourav.poddar at ti.com>
>
> Some flash also support quad read mode. Adding support for quad read
> mode in m25p80 for Spansion and Macronix flash.
>
> [Tweaked by Brian]
>
> With this patch, quad-read support will override fast-read and
> normal-read, if the SPI controller and flash chip both support it.
>
> Signed-off-by: Sourav Poddar<sourav.poddar at ti.com>
> Signed-off-by: Brian Norris<computersforpeace at gmail.com>
I tested this patch version with Spansion(S25FL256S) and
Macronix(MX66L51235F) flash. It worked fine.

Tested-by: Sourav Poddar <sourav.poddar at ti.com>

Thanks for correcting it.
> ---
> v3 ->  v4
>
>    I made a few final tweaks to Sourav's patch. It got the precedence logic
>    wrong, where fast and normal read might override quad-read, and then
>    normal-read would in some cases override either of the others!
>
>   drivers/mtd/devices/m25p80.c | 141 ++++++++++++++++++++++++++++++++++++++++++-
>   1 file changed, 139 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c
> index 04f8a24..f2f781d 100644
> --- a/drivers/mtd/devices/m25p80.c
> +++ b/drivers/mtd/devices/m25p80.c
> @@ -41,6 +41,7 @@
>   #define	OPCODE_WRSR		0x01	/* Write status register 1 byte */
>   #define	OPCODE_NORM_READ	0x03	/* Read data bytes (low frequency) */
>   #define	OPCODE_FAST_READ	0x0b	/* Read data bytes (high frequency) */
> +#define	OPCODE_QUAD_READ        0x6b    /* Read data bytes */
>   #define	OPCODE_PP		0x02	/* Page program (up to 256 bytes) */
>   #define	OPCODE_BE_4K		0x20	/* Erase 4KiB block */
>   #define	OPCODE_BE_4K_PMC	0xd7	/* Erase 4KiB block on PMC chips */
> @@ -48,10 +49,12 @@
>   #define	OPCODE_CHIP_ERASE	0xc7	/* Erase whole flash chip */
>   #define	OPCODE_SE		0xd8	/* Sector erase (usually 64KiB) */
>   #define	OPCODE_RDID		0x9f	/* Read JEDEC ID */
> +#define	OPCODE_RDCR             0x35    /* Read configuration register */
>
>   /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
>   #define	OPCODE_NORM_READ_4B	0x13	/* Read data bytes (low frequency) */
>   #define	OPCODE_FAST_READ_4B	0x0c	/* Read data bytes (high frequency) */
> +#define	OPCODE_QUAD_READ_4B	0x6c    /* Read data bytes */
>   #define	OPCODE_PP_4B		0x12	/* Page program (up to 256 bytes) */
>   #define	OPCODE_SE_4B		0xdc	/* Sector erase (usually 64KiB) */
>
> @@ -76,6 +79,11 @@
>   #define	SR_BP2			0x10	/* Block protect 2 */
>   #define	SR_SRWD			0x80	/* SR write protect */
>
> +#define SR_QUAD_EN_MX           0x40    /* Macronix Quad I/O */
> +
> +/* Configuration Register bits. */
> +#define CR_QUAD_EN_SPAN		0x2     /* Spansion Quad I/O */
> +
>   /* Define max times to check status register before we give up. */
>   #define	MAX_READY_WAIT_JIFFIES	(40 * HZ)	/* M25P16 specs 40s max chip erase */
>   #define	MAX_CMD_SIZE		6
> @@ -87,6 +95,7 @@
>   enum read_type {
>   	M25P80_NORMAL = 0,
>   	M25P80_FAST,
> +	M25P80_QUAD,
>   };
>
>   struct m25p {
> @@ -136,6 +145,26 @@ static int read_sr(struct m25p *flash)
>   }
>
>   /*
> + * Read configuration register, returning its value in the
> + * location. Return the configuration register value.
> + * Returns negative if error occured.
> + */
> +static int read_cr(struct m25p *flash)
> +{
> +	u8 code = OPCODE_RDCR;
> +	int ret;
> +	u8 val;
> +
> +	ret = spi_write_then_read(flash->spi,&code, 1,&val, 1);
> +	if (ret<  0) {
> +		dev_err(&flash->spi->dev, "error %d reading CR\n", ret);
> +		return ret;
> +	}
> +
> +	return val;
> +}
> +
> +/*
>    * Write status register 1 byte
>    * Returns negative if error occurred.
>    */
> @@ -225,6 +254,95 @@ static int wait_till_ready(struct m25p *flash)
>   }
>
>   /*
> + * Write status Register and configuration register with 2 bytes
> + * The first byte will be written to the status register, while the
> + * second byte will be written to the configuration register.
> + * Return negative if error occured.
> + */
> +static int write_sr_cr(struct m25p *flash, u16 val)
> +{
> +	flash->command[0] = OPCODE_WRSR;
> +	flash->command[1] = val&  0xff;
> +	flash->command[2] = (val>>  8);
> +
> +	return spi_write(flash->spi, flash->command, 3);
> +}
> +
> +static int macronix_quad_enable(struct m25p *flash)
> +{
> +	int ret, val;
> +	u8 cmd[2];
> +	cmd[0] = OPCODE_WRSR;
> +
> +	val = read_sr(flash);
> +	cmd[1] = val | SR_QUAD_EN_MX;
> +	write_enable(flash);
> +
> +	spi_write(flash->spi,&cmd, 2);
> +
> +	if (wait_till_ready(flash))
> +		return 1;
> +
> +	ret = read_sr(flash);
> +	if (!(ret>  0&&  (ret&  SR_QUAD_EN_MX))) {
> +		dev_err(&flash->spi->dev,
> +			"Macronix Quad bit not set");
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static int spansion_quad_enable(struct m25p *flash)
> +{
> +	int ret;
> +	int quad_en = CR_QUAD_EN_SPAN<<  8;
> +
> +	write_enable(flash);
> +
> +	ret = write_sr_cr(flash, quad_en);
> +	if (ret<  0) {
> +		dev_err(&flash->spi->dev,
> +			"error while writing configuration register");
> +		return -EINVAL;
> +	}
> +
> +	/* read back and check it */
> +	ret = read_cr(flash);
> +	if (!(ret>  0&&  (ret&  CR_QUAD_EN_SPAN))) {
> +		dev_err(&flash->spi->dev,
> +			"Spansion Quad bit not set");
> +		return -EINVAL;
> +	}
> +
> +	return 0;
> +}
> +
> +static int set_quad_mode(struct m25p *flash, u32 jedec_id)
> +{
> +	int status;
> +
> +	switch (JEDEC_MFR(jedec_id)) {
> +	case CFI_MFR_MACRONIX:
> +		status = macronix_quad_enable(flash);
> +		if (status) {
> +			dev_err(&flash->spi->dev,
> +				"Macronix quad-read not enabled");
> +			return -EINVAL;
> +		}
> +		return status;
> +	default:
> +		status = spansion_quad_enable(flash);
> +		if (status) {
> +			dev_err(&flash->spi->dev,
> +				"Spansion quad-read not enabled");
> +			return -EINVAL;
> +		}
> +		return status;
> +	}
> +}
> +
> +/*
>    * Erase the whole flash memory
>    *
>    * Returns 0 if successful, non-zero otherwise.
> @@ -363,6 +481,7 @@ static inline int m25p80_dummy_cycles_read(struct m25p *flash)
>   {
>   	switch (flash->flash_read) {
>   	case M25P80_FAST:
> +	case M25P80_QUAD:
>   		return 1;
>   	case M25P80_NORMAL:
>   		return 0;
> @@ -727,6 +846,7 @@ struct flash_info {
>   #define	SST_WRITE	0x04		/* use SST byte programming */
>   #define	M25P_NO_FR	0x08		/* Can't do fastread */
>   #define	SECT_4K_PMC	0x10		/* OPCODE_BE_4K_PMC works uniformly */
> +#define	M25P80_QUAD_READ	0x20    /* Flash supports Quad Read */
>   };
>
>   #define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags)	\
> @@ -804,7 +924,7 @@ static const struct spi_device_id m25p_ids[] = {
>   	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
>   	{ "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) },
>   	{ "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) },
> -	{ "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, 0) },
> +	{ "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, M25P80_QUAD_READ) },
>
>   	/* Micron */
>   	{ "n25q064",     INFO(0x20ba17, 0, 64 * 1024,  128, 0) },
> @@ -824,7 +944,7 @@ static const struct spi_device_id m25p_ids[] = {
>   	{ "s25sl032p",  INFO(0x010215, 0x4d00,  64 * 1024,  64, 0) },
>   	{ "s25sl064p",  INFO(0x010216, 0x4d00,  64 * 1024, 128, 0) },
>   	{ "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) },
> -	{ "s25fl256s1", INFO(0x010219, 0x4d01,  64 * 1024, 512, 0) },
> +	{ "s25fl256s1", INFO(0x010219, 0x4d01,  64 * 1024, 512, M25P80_QUAD_READ) },
>   	{ "s25fl512s",  INFO(0x010220, 0x4d00, 256 * 1024, 256, 0) },
>   	{ "s70fl01gs",  INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) },
>   	{ "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024,  64, 0) },
> @@ -966,6 +1086,7 @@ static int m25p_probe(struct spi_device *spi)
>   	unsigned			i;
>   	struct mtd_part_parser_data	ppdata;
>   	struct device_node *np = spi->dev.of_node;
> +	int ret;
>
>   	/* Platform data helps sort out which chip type we have, as
>   	 * well as how this board partitions it.  If we don't have
> @@ -1093,8 +1214,21 @@ static int m25p_probe(struct spi_device *spi)
>   	if (info->flags&  M25P_NO_FR)
>   		flash->flash_read = M25P80_NORMAL;
>
> +	/* Quad-read mode takes precedence over fast/normal */
> +	if (spi->mode&  SPI_RX_QUAD&&  info->flags&  M25P80_QUAD_READ) {
> +		ret = set_quad_mode(flash, info->jedec_id);
> +		if (ret) {
> +			dev_err(&flash->spi->dev, "quad mode not supported\n");
> +			return ret;
> +		}
> +		flash->flash_read = M25P80_QUAD;
> +	}
> +
>   	/* Default commands */
>   	switch (flash->flash_read) {
> +	case M25P80_QUAD:
> +		flash->read_opcode = OPCODE_QUAD_READ;
> +		break;
>   	case M25P80_FAST:
>   		flash->read_opcode = OPCODE_FAST_READ;
>   		break;
> @@ -1116,6 +1250,9 @@ static int m25p_probe(struct spi_device *spi)
>   		if (JEDEC_MFR(info->jedec_id) == CFI_MFR_AMD) {
>   			/* Dedicated 4-byte command set */
>   			switch (flash->flash_read) {
> +			case M25P80_QUAD:
> +				flash->read_opcode = OPCODE_QUAD_READ;
> +				break;
>   			case M25P80_FAST:
>   				flash->read_opcode = OPCODE_FAST_READ_4B;
>   				break;




More information about the linux-mtd mailing list