[PATCH 0/5 v3] at91: PMECC: enable PMECC in dt for at91sam9x5ek, at91sam9n12ek

[Nicolas Ferre]

On 01/23/2013 01:47 PM, Josh Wu :
> Those patches will enable PMECC in dt parameters for at91sam9x5ek and 
> at91sam9n12ek.
> 
> The PMECC driver will check minimum required ecc on ONFI parameter from NAND 
> flash.
> 
> If pmecc-cap, pmecc-sector-size in dts file is specified, use those two.
> otherwise, set those according to NAND flash ONFI parameters.
> 
> If the pmecc-cap, pmecc-sector-size in dts are different with ecc requirement
> in ONFI, print out a warning.
> 
> 
> For the following compile error:
>   ERROR (phandle_references): Reference to non-existent node or label "pinctrl_ssc0_tx"
> 
>   ERROR: Input tree has errors, aborting (use -f to force output)
>   make[2]: *** [arch/arm/boot/dts/at91sam9g20ek.dtb] Error 2
> 
> the fixes are already merged in Linux mainline in v3.8-rc4.
> you can find in: 
>  544ae6b2e676c3c37fb8c93ef9327932fc2e5bc2 (ARM: at91/dts: add pinctrl support for SSC peripheral)
>  ea03c81521bde526570e1dec96eaa21fe5ac84a2 (ASoC: atmel-ssc: add pinctrl selection to driver) 

Artem,

I propose to take patches 2 and 3/5 of this series via arm-soc git tree.
I will specify to merge them at the end of the merge-window so that the
Device Tree properties will not be out-of-sync with driver modifications
(may not cause big issues anyway).

If it is needed, you can add my:

Acked-by: Nicolas Ferre <nicolas.ferre at atmel.com>

On the whole patch series.

Tell me if I have to rebase it for removing the 2nd and 3rd patches or
if you can deal with this yourself.

Thanks for your help. best regards,


> Change logs:
> v2: rebase to v3.8-rc3. And wrapped the commit message.
> 
> v3: big chages:
>   1. reduce the PMECC lookup table mapping. Just the lookup table not whole
>      ROM code according to J.C's suggestion.
>   2. use simpler strategy to handle pmecc-cap, pmecc-sector-size:
>      * make pmecc-cap, pmecc-sector-size optional.
>      * If pmecc-cap, pmecc-sector-size are not set, use ONFI ecc parameters.
>        otherwise, use those in DTS file.
>      * print out a warning if PMECC use different ecc bits or sector size 
>        from ONFI ecc parameters.
> 
> Josh Wu (5):
>   MTD: atmel_nand: avoid to report an error when lookup table offset is
>     0.
>   ARM: at91: at91sam9x5: add DT parameters to enable PMECC
>   ARM: at91: at91sam9n12: add DT parameters to enable PMECC
>   MTD: atmel_nand: make pmecc-cap, pmecc-sector-size in dts is
>     optional.
>   MTD: at91: atmel_nand: for PMECC, add code to check the ONFI
>     parameter ECC requirement.
> 
>  arch/arm/boot/dts/at91sam9n12.dtsi  |    3 +-
>  arch/arm/boot/dts/at91sam9n12ek.dts |    5 +-
>  arch/arm/boot/dts/at91sam9x5.dtsi   |    4 +
>  arch/arm/boot/dts/at91sam9x5cm.dtsi |    5 +-
>  drivers/mtd/nand/atmel_nand.c       |  141 +++++++++++++++++++++++++++++------
>  5 files changed, 131 insertions(+), 27 deletions(-)
> 


-- 
Nicolas Ferre