[PATCH v3] ARM: davinci: aemif: get rid of davinci-nand driver dependency on aemif
ivan.khoronzhuk
ivan.khoronzhuk at ti.com
Wed Dec 18 06:51:32 EST 2013
On 12/05/2013 08:11 PM, Ivan Khoronzhuk wrote:
> The problem that the set timings code contains the call of Davinci
> platform function davinci_aemif_setup_timing() which is not
> accessible if kernel is built for another platform like Keystone.
>
> The Keysone platform is going to use TI AEMIF driver.
> If TI AEMIF is used we don't need to set timings and bus width.
> It is done by AEMIF driver.
>
> To get rid of davinci-nand driver dependency on aemif platform code
> we moved aemif code to davinci platform.
>
> The platform AEMIF code (aemif.c) has to be removed once Davinci
> will be converted to DT and use ti-aemif.c driver.
>
> Signed-off-by: Sekhar Nori <nsekhar at ti.com>
> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk at ti.com>
> ---
> v3..v2:
> - rebased on following patch series:
> [PATCH v3 0/9] Reuse davinci-nand driver for Keystone arch
> http://www.spinics.net/lists/arm-kernel/msg291723.html
> - removed AEMIF setup from next boards:
> arch/arm/mach-davinci/board-dm355-evm.c
> arch/arm/mach-davinci/board-dm355-leopard.c
> arch/arm/mach-davinci/board-dm365-evm.c
> arch/arm/mach-davinci/board-neuros-osd2.c
> arch/arm/mach-davinci/devices-tnetv107x.c
> - removed repeated clk_get() from davinci_aemif_setup_timing()
>
> v2..v1:
> - enabled AEMIF clock
> - removed EXPORT_SYMBOL(davinci_aemif_setup)
> - renamed ugly name davinci_ntosd2_nandflash_device
> CC:
> Sekhar Nori <nsekhar at ti.com>
>
> arch/arm/mach-davinci/aemif.c | 106 ++++++++++++++++++++---
> arch/arm/mach-davinci/board-da830-evm.c | 3 +
> arch/arm/mach-davinci/board-da850-evm.c | 3 +
> arch/arm/mach-davinci/board-dm644x-evm.c | 5 ++
> arch/arm/mach-davinci/board-dm646x-evm.c | 3 +
> arch/arm/mach-davinci/board-mityomapl138.c | 3 +
> drivers/mtd/nand/davinci_nand.c | 22 -----
> include/linux/platform_data/mtd-davinci-aemif.h | 5 +-
> 8 files changed, 115 insertions(+), 35 deletions(-)
>
> diff --git a/arch/arm/mach-davinci/aemif.c b/arch/arm/mach-davinci/aemif.c
> index f091a90..7adfb7e 100644
> --- a/arch/arm/mach-davinci/aemif.c
> +++ b/arch/arm/mach-davinci/aemif.c
> @@ -16,6 +16,7 @@
> #include <linux/time.h>
>
> #include <linux/platform_data/mtd-davinci-aemif.h>
> +#include <linux/platform_data/mtd-davinci.h>
>
> /* Timing value configuration */
>
> @@ -43,6 +44,17 @@
> WSTROBE(WSTROBE_MAX) | \
> WSETUP(WSETUP_MAX))
>
> +static inline unsigned int davinci_aemif_readl(void __iomem *base, int offset)
> +{
> + return readl_relaxed(base + offset);
> +}
> +
> +static inline void davinci_aemif_writel(void __iomem *base,
> + int offset, unsigned long value)
> +{
> + writel_relaxed(value, base + offset);
> +}
> +
> /*
> * aemif_calc_rate - calculate timing data.
> * @wanted: The cycle time needed in nanoseconds.
> @@ -76,6 +88,7 @@ static int aemif_calc_rate(int wanted, unsigned long clk, int max)
> * @t: timing values to be progammed
> * @base: The virtual base address of the AEMIF interface
> * @cs: chip-select to program the timing values for
> + * @clkrate: the AEMIF clkrate
> *
> * This function programs the given timing values (in real clock) into the
> * AEMIF registers taking the AEMIF clock into account.
> @@ -86,24 +99,17 @@ static int aemif_calc_rate(int wanted, unsigned long clk, int max)
> *
> * Returns 0 on success, else negative errno.
> */
> -int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
> - void __iomem *base, unsigned cs)
> +static int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
> + void __iomem *base, unsigned cs,
> + unsigned long clkrate)
> {
> unsigned set, val;
> int ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup;
> unsigned offset = A1CR_OFFSET + cs * 4;
> - struct clk *aemif_clk;
> - unsigned long clkrate;
>
> if (!t)
> return 0; /* Nothing to do */
>
> - aemif_clk = clk_get(NULL, "aemif");
> - if (IS_ERR(aemif_clk))
> - return PTR_ERR(aemif_clk);
> -
> - clkrate = clk_get_rate(aemif_clk);
> -
> clkrate /= 1000; /* turn clock into kHz for ease of use */
>
> ta = aemif_calc_rate(t->ta, clkrate, TA_MAX);
> @@ -130,4 +136,82 @@ int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
>
> return 0;
> }
> -EXPORT_SYMBOL(davinci_aemif_setup_timing);
> +
> +/**
> + * davinci_aemif_setup - setup AEMIF interface by davinci_nand_pdata
> + * @pdev - link to platform device to setup settings for
> + *
> + * This function does not use any locking while programming the AEMIF
> + * because it is expected that there is only one user of a given
> + * chip-select.
> + *
> + * Returns 0 on success, else negative errno.
> + */
> +int davinci_aemif_setup(struct platform_device *pdev)
> +{
> + struct davinci_nand_pdata *pdata = dev_get_platdata(&pdev->dev);
> + uint32_t val;
> + unsigned long clkrate;
> + struct resource *res;
> + void __iomem *base;
> + struct clk* clk;
> + int ret = 0;
> +
> + clk = clk_get(&pdev->dev, "aemif");
> + if (IS_ERR(clk)) {
> + ret = PTR_ERR(clk);
> + dev_dbg(&pdev->dev, "unable to get AEMIF clock, err %d\n", ret);
> + return ret;
> + }
> +
> + ret = clk_prepare_enable(clk);
> + if (ret < 0) {
> + dev_dbg(&pdev->dev, "unable to enable AEMIF clock, err %d\n",
> + ret);
> + return ret;
> + }
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + if (!res) {
> + dev_err(&pdev->dev, "cannot get IORESOURCE_MEM\n");
> + ret = -ENOMEM;
> + goto err;
> + }
> +
> + base = ioremap(res->start, resource_size(res));
> + if (!base) {
> + dev_err(&pdev->dev, "ioremap failed for resource %pR\n", res);
> + ret = -ENOMEM;
> + goto err;
> + }
> +
> + /*
> + * Setup Async configuration register in case we did not boot
> + * from NAND and so bootloader did not bother to set it up.
> + */
> + val = davinci_aemif_readl(base, A1CR_OFFSET + pdev->id * 4);
> + /*
> + * Extended Wait is not valid and Select Strobe mode is not
> + * used
> + */
> + val &= ~(ACR_ASIZE_MASK | ACR_EW_MASK | ACR_SS_MASK);
> + if (pdata->options & NAND_BUSWIDTH_16)
> + val |= 0x1;
> +
> + davinci_aemif_writel(base, A1CR_OFFSET + pdev->id * 4, val);
> +
> + clkrate = clk_get_rate(clk);
> +
> + if (pdata->timing)
> + ret = davinci_aemif_setup_timing(pdata->timing, base, pdev->id,
> + clkrate);
> +
> + if (ret < 0)
> + dev_dbg(&pdev->dev, "NAND timing values setup fail\n");
> +
> + iounmap(base);
> +err:
> + clk_disable_unprepare(clk);
> + clk_put(clk);
> + return ret;
> +}
> diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
> index d1f45af..5623131 100644
> --- a/arch/arm/mach-davinci/board-da830-evm.c
> +++ b/arch/arm/mach-davinci/board-da830-evm.c
> @@ -419,6 +419,9 @@ static inline void da830_evm_init_nand(int mux_mode)
> if (ret)
> pr_warning("da830_evm_init: NAND device not registered.\n");
>
> + if (davinci_aemif_setup(&da830_evm_nand_device))
> + pr_warn("%s: Cannot configure AEMIF.\n", __func__);
> +
> gpio_direction_output(mux_mode, 1);
> }
> #else
> diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
> index e0af0ec..234c5bb 100644
> --- a/arch/arm/mach-davinci/board-da850-evm.c
> +++ b/arch/arm/mach-davinci/board-da850-evm.c
> @@ -358,6 +358,9 @@ static inline void da850_evm_setup_nor_nand(void)
>
> platform_add_devices(da850_evm_devices,
> ARRAY_SIZE(da850_evm_devices));
> +
> + if (davinci_aemif_setup(&da850_evm_nandflash_device))
> + pr_warn("%s: Cannot configure AEMIF.\n", __func__);
> }
> }
>
> diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
> index 987605b7..5602957 100644
> --- a/arch/arm/mach-davinci/board-dm644x-evm.c
> +++ b/arch/arm/mach-davinci/board-dm644x-evm.c
> @@ -778,6 +778,11 @@ static __init void davinci_evm_init(void)
> /* only one device will be jumpered and detected */
> if (HAS_NAND) {
> platform_device_register(&davinci_evm_nandflash_device);
> +
> + if (davinci_aemif_setup(&davinci_evm_nandflash_device))
> + pr_warn("%s: Cannot configure AEMIF.\n",
> + __func__);
> +
> evm_leds[7].default_trigger = "nand-disk";
> if (HAS_NOR)
> pr_warning("WARNING: both NAND and NOR flash "
> diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
> index 13d0801..ae129bc 100644
> --- a/arch/arm/mach-davinci/board-dm646x-evm.c
> +++ b/arch/arm/mach-davinci/board-dm646x-evm.c
> @@ -805,6 +805,9 @@ static __init void evm_init(void)
>
> platform_device_register(&davinci_nand_device);
>
> + if (davinci_aemif_setup(&davinci_nand_device))
> + pr_warn("%s: Cannot configure AEMIF.\n", __func__);
> +
> dm646x_init_edma(dm646x_edma_rsv);
>
> if (HAS_ATA)
> diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
> index 7aa105b..98a66ff 100644
> --- a/arch/arm/mach-davinci/board-mityomapl138.c
> +++ b/arch/arm/mach-davinci/board-mityomapl138.c
> @@ -432,6 +432,9 @@ static void __init mityomapl138_setup_nand(void)
> {
> platform_add_devices(mityomapl138_devices,
> ARRAY_SIZE(mityomapl138_devices));
> +
> + if (davinci_aemif_setup(&mityomapl138_nandflash_device))
> + pr_warn("%s: Cannot configure AEMIF.\n", __func__);
> }
>
> static const short mityomap_mii_pins[] = {
> diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
> index 0cd4dbc..4463b0e 100644
> --- a/drivers/mtd/nand/davinci_nand.c
> +++ b/drivers/mtd/nand/davinci_nand.c
> @@ -741,28 +741,6 @@ static int __init nand_davinci_probe(struct platform_device *pdev)
> goto err_clk_enable;
> }
>
> - /*
> - * Setup Async configuration register in case we did not boot from
> - * NAND and so bootloader did not bother to set it up.
> - */
> - val = davinci_nand_readl(info, A1CR_OFFSET + info->core_chipsel * 4);
> -
> - /* Extended Wait is not valid and Select Strobe mode is not used */
> - val &= ~(ACR_ASIZE_MASK | ACR_EW_MASK | ACR_SS_MASK);
> - if (info->chip.options & NAND_BUSWIDTH_16)
> - val |= 0x1;
> -
> - davinci_nand_writel(info, A1CR_OFFSET + info->core_chipsel * 4, val);
> -
> - ret = 0;
> - if (info->timing)
> - ret = davinci_aemif_setup_timing(info->timing, info->base,
> - info->core_chipsel);
> - if (ret < 0) {
> - dev_dbg(&pdev->dev, "NAND timing values setup fail\n");
> - goto err;
> - }
> -
> spin_lock_irq(&davinci_nand_lock);
>
> /* put CSxNAND into NAND mode */
> diff --git a/include/linux/platform_data/mtd-davinci-aemif.h b/include/linux/platform_data/mtd-davinci-aemif.h
> index 05b2934..97948ac 100644
> --- a/include/linux/platform_data/mtd-davinci-aemif.h
> +++ b/include/linux/platform_data/mtd-davinci-aemif.h
> @@ -10,6 +10,8 @@
> #ifndef _MACH_DAVINCI_AEMIF_H
> #define _MACH_DAVINCI_AEMIF_H
>
> +#include <linux/platform_device.h>
> +
> #define NRCSR_OFFSET 0x00
> #define AWCCR_OFFSET 0x04
> #define A1CR_OFFSET 0x10
> @@ -31,6 +33,5 @@ struct davinci_aemif_timing {
> u8 ta;
> };
>
> -int davinci_aemif_setup_timing(struct davinci_aemif_timing *t,
> - void __iomem *base, unsigned cs);
> +int davinci_aemif_setup(struct platform_device *pdev);
> #endif
>
Hi, Sekhar
This patch is based on "Reuse davinci-nand driver for Keystone arch" series.
The series has passed review at https://lkml.org/lkml/2013/12/17/241
and can be found at http://git.infradead.org/l2-mtd.git
This patch can be still applied on top of the series without conflicts.
Can you please pick up the $subject patch if you are OK with it?
--
Regards,
Ivan Khoronzhuk
More information about the linux-mtd
mailing list