[PATCHv2 04/10] spi/qspi: configure set up register for memory map.

[Marek Vasut]

On Friday, December 06, 2013 at 03:24:45 PM, Sourav Poddar wrote:
> These add api to configure set up registers which will be used
> for memory mapped operations.
> 
> These was provided as a pointer in the earlier patch and can be
> used by the slave devices to configure the master controller as an
> when required according to the usecases.
> 
> Signed-off-by: Sourav Poddar <sourav.poddar at ti.com>
> ---
>  drivers/spi/spi-ti-qspi.c |   29 +++++++++++++++++++++++++++++
>  1 files changed, 29 insertions(+), 0 deletions(-)
> 
> diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
> index 48294d1..e4a8afc 100644
> --- a/drivers/spi/spi-ti-qspi.c
> +++ b/drivers/spi/spi-ti-qspi.c
> @@ -117,6 +117,10 @@ struct ti_qspi {
>  #define MEM_CS		(1 << 8)
>  #define MEM_CS_DIS	(0 << 8)
> 
> +#define QSPI_SETUP0_RD_NORMAL   (0x0 << 12)
> +#define QSPI_SETUP0_RD_DUAL     (0x1 << 12)
> +#define QSPI_SETUP0_RD_QUAD     (0x3 << 12)
> +
>  #define	QSPI_FRAME			4096
> 
>  #define QSPI_AUTOSUSPEND_TIMEOUT         2000
> @@ -220,6 +224,30 @@ static int ti_qspi_setup(struct spi_device *spi)
>  	return 0;
>  }
> 
> +static void ti_qspi_configure_from_slave(struct spi_device *spi)
> +{
> +	struct ti_qspi  *qspi = spi_master_get_devdata(spi->master);
> +	struct slave_info info = spi->info;
> +	u32 memval, mode;
> +
> +	mode = spi->mode & (SPI_RX_DUAL | SPI_RX_QUAD);
> +	memval =  (info.read_opcode << 0) | (info.program_opcode << 16) |
> +		((info.addr_width - 1) << 8) | (info.dummy_cycles << 10);
> +
> +	switch (mode) {
> +	case SPI_RX_DUAL:
> +		memval |= QSPI_SETUP0_RD_DUAL;
> +		break;
> +	case SPI_RX_QUAD:
> +		memval |= QSPI_SETUP0_RD_QUAD;
> +		break;
> +	default:

You want to catch invalid/unsupported mode here instead, so please add 'case 0:' 
for 1-bit transfer and treat default: as an error .

> +		memval |= QSPI_SETUP0_RD_NORMAL;
> +		break;
> +	}
> +	ti_qspi_write(qspi, memval, QSPI_SPI_SETUP0_REG);
> +}
> +
>  static void ti_qspi_restore_ctx(struct ti_qspi *qspi)
>  {
>  	struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg;
> @@ -488,6 +516,7 @@ static int ti_qspi_probe(struct platform_device *pdev)
>  	master->dev.of_node = pdev->dev.of_node;
>  	master->bits_per_word_mask = BIT(32 - 1) | BIT(16 - 1) | BIT(8 - 1);
>  	master->mmap = true;
> +	master->configure_from_slave = ti_qspi_configure_from_slave;
> 
>  	if (!of_property_read_u32(np, "num-cs", &num_cs))
>  		master->num_chipselect = num_cs;

Best regards,
Marek Vasut