[PATCH 2/2] memory: ti-aemif: add bindings for AEMIF driver

[Santosh Shilimkar]

Kumar,

On Tuesday 26 November 2013 11:27 AM, Grygorii Strashko wrote:
> On 11/22/2013 11:04 PM, Kumar Gala wrote:
>>
>> On Nov 20, 2013, at 9:46 AM, Ivan Khoronzhuk <ivan.khoronzhuk at ti.com> wrote:
>>
>>> Add bindings for AEMIF controller drivers/memory/ti-aemif.c
>>>
>>
>> Binding shouldn’t normally refer to code.
>>
>> Just saying something like:
>>
>> Adding binging for TI Async External Memory Interface (AEMIF) controller.
>>
>>
>>> Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk at ti.com>
>>> ---
>>> .../bindings/memory-controllers/ti-aemif.txt       |  198 ++++++++++++++++++++
>>> 1 file changed, 198 insertions(+)
>>> create mode 100644 Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
>>>
>>> diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
>>> new file mode 100644
>>> index 0000000..be0c0cb
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt
>>> @@ -0,0 +1,198 @@
>>> +* Device tree bindings for Texas instruments AEMIF controller
>>> +
>>> +Th Async External Memory Interface (EMIF16/AEMIF) controller is intended to
>>
>> The?
>>
>>> +provide a glue-less interface to a variety of asynchronous memory devices like
>>> +ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories
>>> +can be accessed at any given time via four chip selects with 64M byte access
>>> +per chip select. Synchronous memories such as DDR1 SD RAM, SDR SDRAM
>>> +and Mobile SDR are not supported.
>>> +
>>> +Documentation:
>>> +Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
>>> +OMAP-L138 - http://www.ti.com/lit/ug/spruh77a/spruh77a.pdf
>>> +Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
>>> +
>>> +Required properties:
>>> +
>>> +- compatible:		"ti,davinci-aemif"
>>> +			"ti,keystone-aemif"
>>> +			"ti,omap-L138-aemif"
>>> +
>>> +- #address-cells:	Must be 2. The first cell is the memory partition
>>> +			number. The 0 partition is for chip selects. And the
>>> +			second cell is the offset into the partition, for the 0
>>> +			partition it corresponds to chip select offset.
>>> +
>>
>> Is the first cell just the chip select number?
> 
> No. It's rather memory range/partition number. Now there are 2 partitions:
> - control partition which is common for all CS interfaces
> - CS-specific partition/range
> (this one can be splitted according to specific SoC requirement)
> 
> As per Keystone TCI6638K2K
>  Datasheet http://www.ti.com/lit/ds/sprs836d/sprs836d.pdf:
> 
> 1) the memory range 0 will be from 0x30000000 size 0x10000000:
> 00 3000 0000 - 00 33FF FFFF 64M EMIF16 CE0
> 00 3400 0000 - 00 37FF FFFF 64M EMIF16 CE1
> 00 3800 0000 - 00 3BFF FFFF 64M EMIF16 CE2
> 00 3C00 0000 - 00 3FFF FFFF 64M EMIF16 CE3
> 
> 2) the memory range 1:
> 00 2100 0A00 - 00 2100 0AFF 256 AEMIF Config
> 
> And AEMIF node contains definition:
> ranges = <0 0 0x30000000 0x10000000
> 	  1 0 0x21000A00 0x0000100>;
> 
> 
> Child node has (nand):
>  reg = <0 0 0x4000000 (cs0)
>         - or - 0 0x4000000 0x4000000 (cs1)
>         - or - 0 0x8000000 0x4000000 (cs2)
> 	- or - 0 0xC000000 0x4000000 (cs3)
> 	- and -
>         1 0 0x0000100>; (for all cs)
> 
> For example for cs2 child node the resulting mem range 0 will be calculated as
> 
> from: 0x30000000 + (0 0x8000000 - 0 0)
> size: 0x4000000
> 
> We don't encode CS number in reg/ranges, because it will allow simply change 
> AEMIF DT definitions depending on each SoC
> (AEMIF CS memory range can be continuous as above or not, if not - additional
> range/partition can be added and child device can select the proper one).
> 
>>
>> I’m wondering if this is similar to FSL Localbus controller, see the binding:
>>
>> bindings/powerpc/fsl/lbc.txt
> 
> Don't think so :) it looks similar just because of using standard bindings
> (gpmc-nand.c mvebu-devbus.txt ti-gpmc.txt and etc.)
> 
>>
>>> +- #size-cells:		Must be set to 1.
>>> +
>>> +- reg:			contains offset/length value for AEMIF control registers
>>> +			space.
>>> +
>>> +- ranges:		Must be set up to reflect the memory layout for 4
>>> +			chipselects and for AEMIF control range.
>>> +
>>> +- clocks:		phandle reference to the controller clock. Required only
>>> +			if clock tree data present in device tree.
>>> +			See clock-bindings.txt

Are you ok with above description on why cs property is needed. We will need
your ack ;-) to take these patches forward.

Regards,
Santosh