[PATCH v2] mtd: nand: Add driver for M-sys / Sandisk diskonchip G4
Mike Dunn
mikedunn at newsguy.com
Wed Nov 2 19:00:59 EDT 2011
This is a nand driver for the diskonchip G4 in my Palm Treo680. It's been
fairly well tested; it passes the nandtest utility in mtd-utils, and also the
kernel tests mtd_pagetest and mtd_readtest. A ubifs was created on it and seems
to be working well, though stress testing is needed.
This version 2 includes a lot of cleanup, stylistic improvements, removal of BCH
algorithmic code that was redundant with the existing kernel algorithm, and some
refactoring. The #defines related to the device registers were made
consistent with those in the diskonchip G3 driver currently under development,
in anticipation of a shared header file (at least) between the two drivers at
some point. Thanks to everyone who took the time to review and comment on the
earlier version.
Hopefully some mtd experts can share their opinion on the suitability of the
nand interface for these devices. This G4 driver uses it, the G3 driver does
not. It would probably be a bad thing for two similiar devices to interface
with the mtd subsystem differently.
Signed-off-by: Mike Dunn <mikedunn at newsguy.com>
---
This was tested against the latest mtd-2.6 kernel from the git repository on
infradead.org, but I also verified that it builds against Artem's l2-mtd-2.6
kernel.
drivers/mtd/nand/Kconfig | 12 +
drivers/mtd/nand/Makefile | 1 +
drivers/mtd/nand/docg4.c | 1199 +++++++++++++++++++++++++++++++++++++++++++++
include/linux/mtd/docg4.h | 24 +
4 files changed, 1236 insertions(+), 0 deletions(-)
create mode 100644 drivers/mtd/nand/docg4.c
create mode 100644 include/linux/mtd/docg4.h
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index 4c34252..abb5a33 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -319,6 +319,18 @@ config MTD_NAND_DISKONCHIP_BBTWRITE
load time (assuming you build diskonchip as a module) with the module
parameter "inftl_bbt_write=1".
+config MTD_NAND_DOCG4
+ tristate "Support for DiskOnChip G4 (EXPERIMENTAL)"
+ depends on EXPERIMENTAL
+ select BCH
+ select BITREVERSE
+ help
+ Support for diskonchip G4 nand flash, found in several smartphones,
+ such as the Palm Treo680 and HTC Prophet.
+
+ There is currently no support for the saftl filesystem; however a
+ ubifs has been succesfully tested on the device.
+
config MTD_NAND_SHARPSL
tristate "Support for NAND Flash on Sharp SL Series (C7xx + others)"
depends on ARCH_PXA
diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
index 5745d83..70993e7 100644
--- a/drivers/mtd/nand/Makefile
+++ b/drivers/mtd/nand/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_MTD_NAND_PPCHAMELEONEVB) += ppchameleonevb.o
obj-$(CONFIG_MTD_NAND_S3C2410) += s3c2410.o
obj-$(CONFIG_MTD_NAND_DAVINCI) += davinci_nand.o
obj-$(CONFIG_MTD_NAND_DISKONCHIP) += diskonchip.o
+obj-$(CONFIG_MTD_NAND_DOCG4) += docg4.o
obj-$(CONFIG_MTD_NAND_FSMC) += fsmc_nand.o
obj-$(CONFIG_MTD_NAND_H1900) += h1910.o
obj-$(CONFIG_MTD_NAND_RTC_FROM4) += rtc_from4.o
diff --git a/drivers/mtd/nand/docg4.c b/drivers/mtd/nand/docg4.c
new file mode 100644
index 0000000..227ed0c
--- /dev/null
+++ b/drivers/mtd/nand/docg4.c
@@ -0,0 +1,1199 @@
+/*
+ * drivers/mtd/nand/docg4.c
+ *
+ * Copyright (C) 2011 Mike Dunn <mikedunn at newsguy.com>
+ *
+ * mtd nand driver for M-Systems DiskOnChip G4 device
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ *
+ * TODO:
+ *
+ * Read factory bad block table (on page 4) during initialization and update
+ * the memory bbt accordingly.
+ *
+ * Implement power mgmt fns (suspend and resume)
+ *
+ * Support cmd-line partitions?
+ *
+ * Support raw reads / writes?
+ *
+ * Hamming ecc when reading oob only
+ *
+ * Support for multiple cascaded devices ("floors") ?
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/slab.h>
+#include <linux/init.h>
+#include <linux/string.h>
+#include <linux/sched.h>
+#include <linux/delay.h>
+#include <linux/moduleparam.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/bitops.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/docg4.h>
+#include <linux/bch.h>
+#include <linux/bitrev.h>
+
+static int ignore_badblocks;
+module_param(ignore_badblocks, int, 0);
+MODULE_PARM_DESC(ignore_badblocks, "no badblock checking performed");
+
+struct docg4_priv {
+ struct mtd_info *mtd;
+ struct device *dev;
+ void __iomem *virtadr;
+ int status;
+ struct {
+ unsigned int command;
+ int column;
+ int page;
+ } last_command;
+ uint8_t oob_buf[16];
+ uint8_t ecc_buf[7];
+ int oob_page;
+ bool page_erased;
+ struct bch_control *bch;
+};
+
+/*
+ * Defines prefixed with DOCG4 are unique to the diskonchip G4.
+ * All others are shared with other diskonchip devices (e.g., P3, G3).
+ *
+ * Functions with names prefixed with docg4_ are mtd / nand interface functions
+ * (though they may also be called internally). All others are internal.
+ */
+
+#define DOC_IOSPACE_DATA 0x0800
+
+/* register offsets */
+#define DOC_CHIPID 0x1000
+#define DOC_DEVICESELECT 0x100a
+#define DOC_ASICMODE 0x100c
+#define DOC_DATAEND 0x101e
+#define DOC_NOP 0x103e
+
+#define DOC_FLASHSEQUENCE 0x1032
+#define DOC_FLASHCOMMAND 0x1034
+#define DOC_FLASHADDRESS 0x1036
+#define DOC_FLASHCONTROL 0x1038
+#define DOC_ECCCONF0 0x1040
+#define DOC_ECCCONF1 0x1042
+#define DOC_HAMMINGPARITY 0x1046
+#define DOC_BCH_SYNDROM(idx) (0x1048 + idx)
+
+#define DOC_ASICMODECONFIRM 0x1072
+#define DOC_CHIPID_INV 0x1074
+
+#define DOCG4_MYSTERY_REG 0x1050
+#define DOCG4_MYSTERY_REG_2 0x1052
+
+/* DOC_FLASHSEQUENCE register commands */
+#define DOC_SEQ_RESET 0x00
+#define DOC_SEQ_PAGE_SIZE_532 0x03
+#define DOCG4_SEQ_FLUSH 0x29
+#define DOCG4_SEQ_PAGEWRITE 0x16
+#define DOCG4_SEQ_PAGEPROG 0x1e
+#define DOCG4_SEQ_BLOCKERASE 0x24
+
+/* DOC_FLASHCOMMAND register commands */
+#define DOC_CMD_READ_PLANE1 0x00
+#define DOC_CMD_ERASECYCLE2 0xd0
+#define DOC_CMD_READ_STATUS 0x70
+#define DOC_CMD_READ_ALL_PLANES 0x30
+#define DOC_CMD_PROG_BLOCK_ADDR 0x60
+#define DOC_CMD_PROG_CYCLE1 0x80
+#define DOC_CMD_PROG_CYCLE2 0x10
+#define DOC_CMD_RESET 0xff
+
+/* DOC_FLASHCONTROL register bits */
+#define DOC_CTRL_CE 0x10
+#define DOC_CTRL_UNKNOWN 0x40
+#define DOC_CTRL_FLASHREADY 0x01
+
+/* DOC_ECCCONF0 register bits */
+#define DOC_ECCCONF0_READ_MODE 0x8000
+#define DOC_ECCCONF0_AUTO_ECC_ENABLE 0x4000
+#define DOC_ECCCONF0_HAMMING_ENABLE 0x1000
+#define DOC_ECCCONF0_UNKNOWN 0x2000
+#define DOC_ECCCONF0_DATA_BYTES_MASK 0x07ff
+
+/* DOC_ECCCONF1 register bits */
+#define DOC_ECCCONF1_BCH_SYNDROM_ERR 0x80
+#define DOC_ECCCONF1_ECC_ENABLE 0x07
+
+/* DOC_ASICMODE register bits */
+#define DOCG4_RESET 0x04 /* TODO: these two should apply... */
+#define DOCG4_NORMAL 0x05 /* ...to the G3 as well */
+
+/* good status values read after read/write/erase operations */
+#define DOCG4_PROGSTATUS_GOOD 0x51
+#define DOCG4_PROGSTATUS_GOOD_2 0xe0
+
+/*
+ * On read operations (page and oob-only), the first byte read from I/O reg is a
+ * status. On error, it reads 0x73; otherwise, it reads either 0x71 (first read
+ * after reset only) or 0x51, so bit 1 is presumed to be an error indicator.
+ */
+#define DOCG4_READ_ERROR 0x02 /* bit 1 indicates read error */
+
+/* anatomy of the device */
+#define DOCG4_CHIP_SIZE 0x8000000
+#define DOCG4_PAGE_SIZE 0x200
+#define DOCG4_PAGES_PER_BLOCK 0x200
+#define DOCG4_BLOCK_SIZE (DOCG4_PAGES_PER_BLOCK * DOCG4_PAGE_SIZE)
+#define DOCG4_NUMBLOCKS (DOCG4_CHIP_SIZE / DOCG4_BLOCK_SIZE)
+#define DOCG4_OOB_SIZE 0x10
+#define DOCG4_CHIP_SHIFT 27 /* log_2(DOCG4_CHIP_SIZE) */
+#define DOCG4_PAGE_SHIFT 9 /* log_2(DOCG4_PAGE_SIZE) */
+#define DOCG4_ERASE_SHIFT 18 /* log_2(DOCG4_BLOCK_SIZE) */
+
+/* all but the last byte is included in ecc calculation */
+#define DOCG4_BCH_SIZE (DOCG4_PAGE_SIZE + DOCG4_OOB_SIZE - 1)
+
+#define DOCG4_USERDATA_LEN 520 /* 512 byte page plus 8 oob avail to user */
+
+/* expected values from the ID registers */
+#define DOCG4_IDREG1_VALUE 0x0400
+#define DOCG4_IDREG2_VALUE 0xfbff
+
+/* primitive polynomial used to build the Galois field used by hw ecc gen */
+#define DOCG4_PRIMITIVE_POLY 0x4443
+
+#define DOCG4_M 14 /* Galois field is of order 2^14 */
+#define DOCG4_T 4 /* BCH alg corrects up to 4 bit errors */
+
+
+/* value generated by the HW ecc generator upon reading blank page */
+static uint8_t blank_read_hwecc[7] = {
+ 0xcf, 0x72, 0xfc, 0x1b, 0xa9, 0xc7, 0xb9 };
+
+/*
+ * Oob bytes 0 - 6 and byte 15 (the last) are available to the user.
+ * Byte 7 is hamming ecc for first 7 bytes. Bytes 8 - 14 are hw-generated ecc.
+ */
+static struct nand_ecclayout docg4_oobinfo = {
+ .eccbytes = 8,
+ .eccpos = {7, 8, 9, 10, 11, 12, 13, 14},
+ .oobfree = {{0, 7}, {15, 1} }
+};
+
+/* the device has a nop register used to insert precise delays */
+static inline void doc_nop(void __iomem *docptr)
+{
+ writew(0, docptr + DOC_NOP);
+}
+
+static void docg4_read_buf(struct mtd_info *mtd, uint8_t *buf, int len)
+{
+ int i;
+ struct nand_chip *nand = mtd->priv;
+ uint16_t *p = (uint16_t *) buf;
+ len >>= 1;
+
+ for (i = 0; i < len; i++)
+ p[i] = readw(nand->IO_ADDR_R);
+}
+
+static void docg4_write_buf16(struct mtd_info *mtd, const uint8_t *buf, int len)
+{
+ int i;
+ struct nand_chip *nand = mtd->priv;
+ uint16_t *p = (uint16_t *) buf;
+ len >>= 1;
+
+ for (i = 0; i < len; i++)
+ writew(p[i], nand->IO_ADDR_W);
+}
+
+static int docg4_wait(struct mtd_info *mtd, struct nand_chip *nand)
+{
+ /* polls the doc status register waiting for device ready */
+
+ uint16_t flash_status;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ unsigned long timeo = jiffies + (HZ * 10);
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s...\n", __func__);
+
+ /* report any previously unreported error */
+ if (doc->status) {
+ int stat = doc->status;
+ doc->status = 0;
+ return stat;
+ }
+
+ /* hardware quirk of g4 requires reading twice initially */
+ flash_status = readw(docptr + DOC_FLASHCONTROL);
+ flash_status = readw(docptr + DOC_FLASHCONTROL);
+
+ while (!(flash_status & DOC_CTRL_FLASHREADY)) {
+ if (time_after(jiffies, timeo)) {
+ dev_err(doc->dev, "docg4_wait timed out\n");
+ return NAND_STATUS_FAIL;
+ }
+ cpu_relax();
+ flash_status = readb(docptr + DOC_FLASHCONTROL);
+ }
+
+ return NAND_STATUS_READY;
+}
+
+static void docg4_select_chip(struct mtd_info *mtd, int chip)
+{
+ /*
+ * Select among multiple cascaded chips ("floors"). Multiple floors are
+ * not yet supported, so the only valid positive value is 0.
+ */
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: chip %d\n", __func__, chip);
+
+ if (chip < 0)
+ return; /* deselected */
+
+ if (chip > 0)
+ dev_warn(doc->dev, "multiple floors currently unsupported\n");
+
+ writew(0, docptr + DOC_DEVICESELECT);
+}
+
+static void reset(struct mtd_info *mtd, struct nand_chip *nand)
+{
+ /* full device reset */
+
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+
+ writew(DOCG4_RESET, docptr + DOC_ASICMODE);
+ writew(~DOCG4_RESET, docptr + DOC_ASICMODECONFIRM);
+ doc_nop(docptr);
+ writew(DOCG4_NORMAL, docptr + DOC_ASICMODE);
+ writew(~DOCG4_NORMAL, docptr + DOC_ASICMODECONFIRM);
+
+ writew(DOC_ECCCONF1_ECC_ENABLE, docptr + DOC_ECCCONF1);
+
+ docg4_wait(mtd, nand);
+}
+
+static void read_hw_ecc(void __iomem *docptr, uint8_t *ecc_buf)
+{
+ /* read the 7 hw-generated ecc bytes */
+
+ int i;
+ for (i = 0; i < 7; i++) { /* hw quirk; read twice */
+ ecc_buf[i] = readb(docptr + DOC_BCH_SYNDROM(i));
+ ecc_buf[i] = readb(docptr + DOC_BCH_SYNDROM(i));
+ }
+}
+
+static int correct_data(struct mtd_info *mtd, uint8_t *buf, int page)
+{
+ /*
+ * Called after a page read to check for bit errors, and correct them if
+ * so. Up to four bits can be corrected.
+ */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ uint16_t edc_err;
+ int i, numerrs, fixederrs, errpos[4];
+
+ /* read the register that tells us if a read error was detected */
+ edc_err = readw(docptr + DOC_ECCCONF1);
+ edc_err = readw(docptr + DOC_ECCCONF1); /* hw quirk: read twice */
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: edc_err = 0x%02x\n", __func__, edc_err);
+
+ if (!(edc_err & DOC_ECCCONF1_BCH_SYNDROM_ERR))
+ return 0; /* no error bits */
+
+ /* data contains error(s); read the 7 hw-generated ecc bytes */
+ read_hw_ecc(docptr, doc->ecc_buf);
+
+ /* check if ecc bytes are those of a blank page */
+ if (!memcmp(doc->ecc_buf, blank_read_hwecc, 7)) {
+ doc->page_erased = true;
+ return 0; /* blank page; ecc error normal */
+ }
+
+ doc->page_erased = false;
+
+ /*
+ * The hardware ecc unit produces oob_ecc ^ calc_ecc. The kernel's bch
+ * algorithm is used to decode this. However the hw operates on page
+ * data in a bit order that is the reverse of that of the bch alg,
+ * requiring that the bits be reversed on the result. Thanks to Ivan
+ * Djelic for his analysis!
+ */
+ for (i = 0; i < 7; i++)
+ doc->ecc_buf[i] = bitrev8(doc->ecc_buf[i]);
+
+ numerrs = decode_bch(doc->bch, NULL, DOCG4_USERDATA_LEN, NULL,
+ doc->ecc_buf, NULL, errpos);
+
+ if (numerrs == -EBADMSG) {
+ dev_warn(doc->dev, "uncorrectable errors at offset %08x\n",
+ page * DOCG4_PAGE_SIZE);
+ return -1;
+ }
+
+ BUG_ON(numerrs < 0); /* -EINVAL, or anything other than -EBADMSG */
+
+ /* undo last step in BCH alg (modulo mirroring not needed) */
+ for (i = 0; i < numerrs; i++)
+ errpos[i] = (errpos[i] & ~7)|(7-(errpos[i] & 7));
+
+ /* fix the errors */
+ fixederrs = 0;
+ for (i = 0; i < numerrs; i++) {
+ if (errpos[i] > DOCG4_USERDATA_LEN * 8)
+ continue; /* error in ecc oob bytes; ignore */
+ change_bit(errpos[i], (unsigned long *)buf);
+ fixederrs++;
+ }
+
+ dev_notice(doc->dev, "%d error(s) corrected at offset %08x\n",
+ fixederrs, page * DOCG4_PAGE_SIZE);
+
+ return fixederrs;
+}
+
+static uint8_t docg4_read_byte(struct mtd_info *mtd)
+{
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s\n", __func__);
+
+ if (doc->last_command.command == NAND_CMD_STATUS) {
+ int status;
+
+ /*
+ * Previous nand command was status request, so nand
+ * infrastructure code expects to read the status here. If an
+ * error occurred in a previous operation, report it.
+ */
+ doc->last_command.command = 0;
+
+ if (doc->status) {
+ status = doc->status;
+ doc->status = 0;
+ }
+
+ /* why is NAND_STATUS_WP inverse logic?? */
+ else
+ status = NAND_STATUS_WP | NAND_STATUS_READY;
+
+ return status;
+ }
+
+ dev_warn(doc->dev, "unexpectd call to read_byte()\n");
+
+ return 0;
+}
+
+static void write_addr(struct docg4_priv *doc, uint32_t docg4_addr)
+{
+ /* write the four address bytes packed in docg4_addr to the device */
+
+ void __iomem *docptr = doc->virtadr;
+ writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS);
+ docg4_addr >>= 8;
+ writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS);
+ docg4_addr >>= 8;
+ writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS);
+ docg4_addr >>= 8;
+ writeb(docg4_addr & 0xff, docptr + DOC_FLASHADDRESS);
+}
+
+static int read_progstatus(struct docg4_priv *doc)
+{
+ /*
+ * This apparently checks the status of programming.
+ * Called after an erasure, and after page data is written.
+ */
+ void __iomem *docptr = doc->virtadr;
+
+ /* status is read from the I/O reg */
+ uint16_t status1 = readw(docptr + DOC_IOSPACE_DATA);
+ uint16_t status2 = readw(docptr + DOC_IOSPACE_DATA);
+ uint16_t status3 = readw(docptr + DOCG4_MYSTERY_REG);
+
+ DEBUG(MTD_DEBUG_LEVEL3, "docg4: %s: %02x %02x %02x\n",
+ __func__, status1, status2, status3);
+
+ if (status1 != DOCG4_PROGSTATUS_GOOD
+ || status2 != DOCG4_PROGSTATUS_GOOD_2
+ || status3 != DOCG4_PROGSTATUS_GOOD_2) {
+ doc->status = NAND_STATUS_FAIL;
+ dev_warn(doc->dev, "read_progstatus failed: "
+ "%02x, %02x, %02x\n", status1, status2, status3);
+ return -EIO;
+ }
+ return 0;
+}
+
+static int pageprog(struct mtd_info *mtd)
+{
+ /*
+ * Final step in writing a page. Writes the contents of its
+ * internal buffer out the flash array, or some such.
+ */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ int retval = 0;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "docg4: %s\n", __func__);
+
+ writew(DOCG4_SEQ_PAGEPROG, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_PROG_CYCLE2, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ docg4_wait(mtd, nand);
+ writew(DOCG4_SEQ_FLUSH, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_READ_STATUS, docptr + DOC_FLASHCOMMAND);
+ writew(DOC_ECCCONF0_READ_MODE | 4, docptr + DOC_ECCCONF0);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ retval = read_progstatus(doc); /* read status from device */
+ writew(0, docptr + DOC_DATAEND);
+ doc_nop(docptr);
+ docg4_wait(mtd, nand);
+ doc_nop(docptr);
+
+ return retval;
+}
+
+static void sequence_reset(struct mtd_info *mtd)
+{
+ /* common starting sequence for all operations */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+
+ writew(DOC_CTRL_UNKNOWN | DOC_CTRL_CE, docptr + DOC_FLASHCONTROL);
+ writew(DOC_SEQ_RESET, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_RESET, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ docg4_wait(mtd, nand);
+ doc_nop(docptr);
+}
+
+static void read_page_prologue(struct mtd_info *mtd, uint32_t docg4_addr)
+{
+ /* first step in reading a page */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+
+ DEBUG(MTD_DEBUG_LEVEL3,
+ "docg4: %s: g4 page %08x\n", __func__, docg4_addr);
+
+ sequence_reset(mtd);
+
+ writew(DOC_SEQ_PAGE_SIZE_532, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_READ_PLANE1, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+
+ write_addr(doc, docg4_addr);
+
+ doc_nop(docptr);
+ writew(DOC_CMD_READ_ALL_PLANES, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+ doc_nop(docptr);
+
+ docg4_wait(mtd, nand);
+}
+
+static void write_page_prologue(struct mtd_info *mtd, uint32_t docg4_addr)
+{
+ /* first step in writing a page */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+
+ DEBUG(MTD_DEBUG_LEVEL3,
+ "docg4: %s: g4 addr: %x\n", __func__, docg4_addr);
+ sequence_reset(mtd);
+ writew(DOCG4_SEQ_PAGEWRITE, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_PROG_CYCLE1, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+ write_addr(doc, docg4_addr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ docg4_wait(mtd, nand);
+}
+
+static uint32_t mtd_to_docg4_address(int page, int column)
+{
+ /*
+ * Convert mtd address to format used by the device, 32 bit packed.
+ *
+ * Some notes on G4 addressing... The M-Sys documentation on this device
+ * claims that pages are 2K in length, and indeed, the format of the
+ * address used by the device reflects that. But within each page are
+ * four 512 byte "sub-pages", each with its own oob data that is
+ * read/written immediately after the 512 bytes of page data. This oob
+ * data contains the ecc bytes for the preceeding 512 bytes.
+ *
+ * Rather than tell the mtd nand infrastructure that page size is 2k,
+ * with four sub-pages each, we engage in a little subterfuge and tell
+ * the infrastructure code that pages are 512 bytes in size. This is
+ * done because during the course of reverse-engineering the device, I
+ * never observed an instance where an entire 2K "page" was read or
+ * written as a unit. Each "sub-page" is always addressed individually,
+ * its data read/written, and ecc handled before the next "sub-page" is
+ * addressed. Also, MLC nand devices are reported to not have
+ * sub-pages, so they're probably not sub-pages in the mtd sense.
+ *
+ * This requires us to convert addresses passed by the mtd nand
+ * infrastructure code to those used by the device.
+ *
+ * The address that is written to the device consists of four bytes: the
+ * first two are the 2k page number, and the second is the index into
+ * the page. The index is in terms of 16-bit half-words and includes
+ * the preceeding oob data, so e.g., the index into the second
+ * "sub-page" is 0x108, and the full device address of the start of mtd
+ * page 0x201 is 0x00800108. Note that the only valid index values are
+ * those for the start of a 512-byte page, or the start of the oob for
+ * one of those pages (oob-only reads).
+ */
+ int g4_page = page / 4; /* device's 2K page */
+ int g4_index = (page % 4) * 0x108 + column/2; /* offset into page */
+ return (g4_page << 16) | g4_index;
+}
+
+static void docg4_command(struct mtd_info *mtd, unsigned command, int column,
+ int page_addr)
+{
+ /* handle standard nand commands */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ uint32_t g4_addr = mtd_to_docg4_address(page_addr, column);
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s %x, page_addr=%x, column=%x\n",
+ __func__, command, page_addr, column);
+
+ /*
+ * Save the command and its arguments. This enables emulation of
+ * standard flash devices, and also some optimizations.
+ */
+ doc->last_command.command = command;
+ doc->last_command.column = column;
+ doc->last_command.page = page_addr;
+
+ switch (command) {
+
+ case NAND_CMD_RESET:
+ reset(mtd, nand);
+ break;
+
+ case NAND_CMD_READ0:
+ read_page_prologue(mtd, g4_addr);
+ break;
+
+ case NAND_CMD_STATUS:
+ /* next call to read_byte() will expect a status */
+ break;
+
+ case NAND_CMD_SEQIN:
+ write_page_prologue(mtd, g4_addr);
+
+ /* hack for deferred write of oob bytes */
+ if (doc->oob_page == page_addr)
+ memcpy(nand->oob_poi, doc->oob_buf, 16);
+ break;
+
+ case NAND_CMD_PAGEPROG:
+ pageprog(mtd);
+ break;
+
+ /* we don't expect these, based on review of nand_base.c */
+ case NAND_CMD_READOOB:
+ case NAND_CMD_READID:
+ case NAND_CMD_ERASE1:
+ case NAND_CMD_ERASE2:
+ dev_warn(doc->dev, "docg4_command: "
+ "unexpected command 0x%x\n", command);
+ break;
+
+ }
+}
+
+static int docg4_read_page_raw(struct mtd_info *mtd, struct nand_chip *nand,
+ uint8_t *buf, int page)
+{
+ /* TODO: support raw read? */
+ return -ENOTSUPP;
+}
+
+static int docg4_read_page(struct mtd_info *mtd, struct nand_chip *nand,
+ uint8_t *buf, int page)
+{
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ uint16_t status, *buf16;
+ int bits_corrected;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: page %08x\n", __func__, page);
+
+ writew(DOC_ECCCONF0_READ_MODE |
+ DOC_ECCCONF0_HAMMING_ENABLE |
+ DOC_ECCCONF0_UNKNOWN |
+ DOCG4_BCH_SIZE,
+ docptr + DOC_ECCCONF0);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+
+ /* the 1st byte from the I/O reg is a status; the rest is page data */
+ status = readw(docptr + DOC_IOSPACE_DATA);
+ if (status & DOCG4_READ_ERROR) {
+ dev_err(doc->dev,
+ "docg4_read_page: bad status: 0x%02x\n", status);
+ doc->status = NAND_STATUS_FAIL;
+ return -EIO;
+ }
+
+ DEBUG(MTD_DEBUG_LEVEL1, "%s: status = 0x%x\n", __func__, status);
+
+ docg4_read_buf(mtd, buf, DOCG4_PAGE_SIZE); /* read the page data */
+
+ /*
+ * Diskonchips read oob immediately after a page read. Mtd
+ * infrastructure issues a separate command for reading oob after the
+ * page is read. So we save the oob bytes in a local buffer and just
+ * copy it when the command for reading oob arrives.
+ */
+
+ /* first 14 oob bytes read from I/O reg */
+ docg4_read_buf(mtd, doc->oob_buf, 14);
+
+ /* last 2 read from another reg */
+ buf16 = (uint16_t *)(doc->oob_buf + 14);
+ *buf16 = readw(docptr + DOCG4_MYSTERY_REG);
+
+ doc_nop(docptr);
+
+ bits_corrected = correct_data(mtd, buf, page);
+ if (bits_corrected < 0)
+ mtd->ecc_stats.failed++;
+ else
+ mtd->ecc_stats.corrected += bits_corrected;
+
+ writew(0, docptr + DOC_DATAEND);
+
+ return 0;
+}
+
+static int docg4_read_oob(struct mtd_info *mtd, struct nand_chip *nand,
+ int page, int sndcmd)
+{
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ uint16_t status;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: page %x\n", __func__, page);
+
+ /*
+ * Oob bytes are read as part of a normal page read. If the last nand
+ * command was a read of the page whose oob is now being read, just copy
+ * the oob bytes that we saved in a local buffer and avoid a separate
+ * oob read.
+ */
+ if (doc->last_command.command == NAND_CMD_READ0 &&
+ doc->last_command.page == page) {
+ memcpy(nand->oob_poi, doc->oob_buf, 16);
+ return 0;
+ }
+
+ /*
+ * Separate read of oob data only.
+ */
+ docg4_command(mtd, NAND_CMD_READ0, nand->ecc.size, page);
+
+ writew(DOC_ECCCONF0_READ_MODE | DOCG4_OOB_SIZE, docptr + DOC_ECCCONF0);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+
+ /* the 1st byte from the I/O reg is a status; the rest is oob data */
+ status = readw(docptr + DOC_IOSPACE_DATA);
+ if (status & DOCG4_READ_ERROR) {
+ doc->status = NAND_STATUS_FAIL;
+ dev_warn(doc->dev,
+ "docg4_read_oob failed: status = 0x%02x\n", status);
+ return -EIO;
+ }
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: status = 0x%x\n", __func__, status);
+
+ docg4_read_buf(mtd, nand->oob_poi, 16);
+
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ writew(0, docptr + DOC_DATAEND);
+ doc_nop(docptr);
+
+ return 0;
+}
+
+static void docg4_erase_block(struct mtd_info *mtd, int page)
+{
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ uint16_t g4_page;
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: page %04x\n", __func__, page);
+
+ sequence_reset(mtd);
+
+ writew(DOCG4_SEQ_BLOCKERASE, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_PROG_BLOCK_ADDR, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+
+ /* only 2 bytes of address are written to specify erase block */
+ g4_page = (uint16_t)(page / 4); /* to g4's 2k page addressing */
+ writeb(g4_page & 0xff, docptr + DOC_FLASHADDRESS);
+ g4_page >>= 8;
+ writeb(g4_page & 0xff, docptr + DOC_FLASHADDRESS);
+ doc_nop(docptr);
+
+ /* start the erasure */
+ writew(DOC_CMD_ERASECYCLE2, docptr + DOC_FLASHCOMMAND);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ docg4_wait(mtd, nand); /* long wait for erasure */
+
+ writew(DOCG4_SEQ_FLUSH, docptr + DOC_FLASHSEQUENCE);
+ writew(DOC_CMD_READ_STATUS, docptr + DOC_FLASHCOMMAND);
+ writew(DOC_ECCCONF0_READ_MODE | 4, docptr + DOC_ECCCONF0);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+ doc_nop(docptr);
+
+ read_progstatus(doc);
+
+ writew(0, docptr + DOC_DATAEND);
+ doc_nop(docptr);
+ docg4_wait(mtd, nand);
+ doc_nop(docptr);
+}
+
+static void docg4_write_page_raw(struct mtd_info *mtd, struct nand_chip *nand,
+ const uint8_t *buf)
+{
+ /* TODO: support raw write? */
+}
+
+static void docg4_write_page(struct mtd_info *mtd, struct nand_chip *nand,
+ const uint8_t *buf)
+{
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ uint8_t hamming;
+ uint8_t ecc_buf[8];
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s...\n", __func__);
+
+ writew(DOC_ECCCONF0_HAMMING_ENABLE |
+ DOC_ECCCONF0_UNKNOWN |
+ DOCG4_BCH_SIZE,
+ docptr + DOC_ECCCONF0);
+ doc_nop(docptr);
+
+ /* write the page data */
+ nand->write_buf(mtd, buf, DOCG4_PAGE_SIZE);
+
+ /* oob bytes 0 through 5 are written to I/O reg */
+ nand->write_buf(mtd, nand->oob_poi, 6);
+
+ /* oob byte 6 written to a separate reg */
+ writew(nand->oob_poi[6], docptr + DOCG4_MYSTERY_REG_2);
+
+ doc_nop(docptr);
+ doc_nop(docptr);
+
+ /* oob byte 7 is hamming code */
+ hamming = readb(docptr + DOC_HAMMINGPARITY);
+ hamming = readb(docptr + DOC_HAMMINGPARITY); /* gotta read twice */
+ writew(hamming, docptr + DOCG4_MYSTERY_REG_2);
+ doc_nop(docptr);
+
+ /* read the 7 bytes from ecc regs and write to next oob area */
+ read_hw_ecc(docptr, ecc_buf);
+ ecc_buf[7] = nand->oob_poi[15]; /* last byte user-programmed */
+ nand->write_buf(mtd, ecc_buf, 8);
+
+ doc_nop(docptr);
+ doc_nop(docptr);
+ writew(0, docptr + DOC_DATAEND);
+ doc_nop(docptr);
+}
+
+static int docg4_write_oob(struct mtd_info *mtd, struct nand_chip *nand,
+ int page)
+{
+ /*
+ * This is not really supported, because MLC nand must write oob bytes
+ * at the same time as page data. Nonetheless, we save the oob buffer
+ * contents here, and then write it along with the page data if the same
+ * page is subsequently written. This allows user space utilities that
+ * write the oob data prior to the page data to work (e.g., nandwrite).
+ * The disdvantage is that, if the intention was to write oob only, the
+ * operation is quietly ignored. As the nand infrastructure code is
+ * currently written, this scenario has been carefully avoided.
+ */
+
+ /* note that bytes 7..14 are hw generated hamming/ecc and overwritten */
+ struct docg4_priv *doc = nand->priv;
+ doc->oob_page = page;
+ memcpy(doc->oob_buf, nand->oob_poi, 16);
+ return 0;
+}
+
+static int __init read_factory_bbt(struct mtd_info *mtd)
+{
+ /*
+ * The device contains a factory bad block table on page 4, but the
+ * table is not updated by this driver. Instead, this function is
+ * called during initialization to read it and update the memory-based
+ * bbt accordingly.
+ */
+
+ /* TODO: figure out how to interpret the table; mine is all ff's */
+ return 0;
+}
+
+static int docg4_block_markbad(struct mtd_info *mtd, loff_t ofs)
+{
+ /*
+ * Bad blocks are marked in the oob area of the first page of the block.
+ * The default scan_bbt() in the nand infrastructure code works fine for
+ * building the memory-based bbt during initialization. Likewise, the
+ * nand infrastructure function that checks if a block is bad works when
+ * a memory-based bbt is used. This function for marking a block as bad
+ * must replace the nand default because this device does not support
+ * writing only to the oob area (whole page must be written along with
+ * oob).
+ *
+ * Note that the nand infrasructure function block_bad(), which reads
+ * the oob marker, should never be called when a memory-based bbt is
+ * used, and hence is not defined by this driver (and the method is not
+ * initialized to a default because we skip the call to
+ * nand_set_defaults()).
+ */
+ int ret, i;
+ uint8_t *buf;
+ struct nand_chip *nand = mtd->priv;
+ struct nand_bbt_descr *bbtd = nand->badblock_pattern;
+ int block = (int)(ofs >> nand->bbt_erase_shift);
+ int page = (int)(ofs >> nand->page_shift);
+ uint32_t g4_addr = mtd_to_docg4_address(page, 0);
+
+ DEBUG(MTD_DEBUG_LEVEL3, "%s: %08llx\n", __func__, ofs);
+
+ buf = kzalloc(DOCG4_PAGE_SIZE, GFP_KERNEL);
+ if (buf == NULL)
+ return -ENOMEM;
+
+ /* update bbt in memory */
+ nand->bbt[block >> 2] |= 0x01 << ((block & 0x03) << 1);
+
+ /* write bit-wise negation of pattern to oob buffer */
+ memset(nand->oob_poi, 0xff, mtd->oobsize);
+ for (i = 0; i < bbtd->len; i++)
+ nand->oob_poi[bbtd->offs + i] = ~bbtd->pattern[i];
+
+ /* write first page of block */
+ write_page_prologue(mtd, g4_addr);
+ docg4_write_page(mtd, nand, buf);
+ ret = pageprog(mtd);
+ if (!ret)
+ mtd->ecc_stats.badblocks++;
+
+ kfree(buf);
+
+ return ret;
+}
+
+static int docg4_block_neverbad(struct mtd_info *mtd, loff_t ofs, int getchip)
+{
+ /* only called when ignore_badblocks option is set */
+ return 0;
+}
+
+static void __init init_mtd_structs(struct mtd_info *mtd)
+{
+ /* initialize mtd and nand data structures */
+
+ /*
+ * Note that some of the following initializations are not usually
+ * required within a nand driver because they are performed by the nand
+ * infrastructure code as part of nand_scan(). In this case they need
+ * to be initialized here because we skip call to nand_scan_ident() (the
+ * first half of nand_scan()). The call to nand_scan_ident() is skipped
+ * because for this device the chip id is not read in the manner of a
+ * standard nand device. Unfortunately, nand_scan_ident() does other
+ * things as well, such as call nand_set_defaults().
+ */
+
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+
+ mtd->size = DOCG4_CHIP_SIZE;
+ mtd->name = "Msys Diskonchip G4";
+ mtd->writesize = DOCG4_PAGE_SIZE;
+ mtd->erasesize = DOCG4_BLOCK_SIZE;
+ mtd->oobsize = DOCG4_OOB_SIZE;
+ nand->chipsize = DOCG4_CHIP_SIZE;
+ nand->chip_shift = DOCG4_CHIP_SHIFT;
+ nand->bbt_erase_shift = nand->phys_erase_shift = DOCG4_ERASE_SHIFT;
+ nand->chip_delay = 20;
+ nand->page_shift = DOCG4_PAGE_SHIFT;
+ nand->pagemask = 0x3ffff;
+ nand->badblockpos = NAND_LARGE_BADBLOCK_POS;
+ nand->badblockbits = 8;
+ nand->ecc.layout = &docg4_oobinfo;
+ nand->ecc.mode = NAND_ECC_HW_SYNDROME;
+ nand->ecc.size = DOCG4_PAGE_SIZE;
+ nand->ecc.prepad = 8;
+ nand->ecc.bytes = 8;
+ nand->options =
+ NAND_BUSWIDTH_16 | NAND_NO_SUBPAGE_WRITE | NAND_NO_AUTOINCR;
+ nand->IO_ADDR_R = nand->IO_ADDR_W = doc->virtadr + DOC_IOSPACE_DATA;
+ nand->controller = &nand->hwcontrol;
+ spin_lock_init(&nand->controller->lock);
+ init_waitqueue_head(&nand->controller->wq);
+
+ /* methods */
+ nand->cmdfunc = docg4_command;
+ nand->waitfunc = docg4_wait;
+ nand->select_chip = docg4_select_chip;
+ nand->read_byte = docg4_read_byte;
+ nand->block_markbad = docg4_block_markbad;
+ nand->read_buf = docg4_read_buf;
+ nand->write_buf = docg4_write_buf16;
+ nand->scan_bbt = nand_default_bbt;
+ nand->erase_cmd = docg4_erase_block;
+ nand->ecc.read_page = docg4_read_page;
+ nand->ecc.write_page = docg4_write_page;
+ nand->ecc.read_page_raw = docg4_read_page_raw;
+ nand->ecc.write_page_raw = docg4_write_page_raw;
+ nand->ecc.read_oob = docg4_read_oob;
+ nand->ecc.write_oob = docg4_write_oob;
+
+ /*
+ * The way the nand infrastructure code is written, a memory-based bbt
+ * is not created if NAND_SKIP_BBTSCAN is set. With no memory bbt,
+ * nand->block_bad() is called. So when ignoring bad blocks, we skip
+ * the scan and define a dummy block_bad() which always returns 0.
+ */
+ if (ignore_badblocks) {
+ nand->options |= NAND_SKIP_BBTSCAN;
+ nand->block_bad = docg4_block_neverbad;
+ }
+
+}
+
+static int __init read_id_reg(struct mtd_info *mtd, struct nand_chip *nand)
+{
+ struct docg4_priv *doc = nand->priv;
+ void __iomem *docptr = doc->virtadr;
+ uint16_t id1, id2;
+
+ /* check for presence of g4 chip by reading id registers */
+ id1 = readw(docptr + DOC_CHIPID);
+ id1 = readw(docptr + DOCG4_MYSTERY_REG);
+ id2 = readw(docptr + DOC_CHIPID_INV);
+ id2 = readw(docptr + DOCG4_MYSTERY_REG);
+
+ if (id1 == DOCG4_IDREG1_VALUE && id2 == DOCG4_IDREG2_VALUE) {
+ dev_info(doc->dev,
+ "NAND device: 128MiB Diskonchip G4 detected\n");
+ return 0;
+ }
+
+ return -ENODEV;
+}
+
+static int __init probe_docg4(struct platform_device *pdev)
+{
+ struct mtd_info *mtd;
+ struct nand_chip *nand;
+ void __iomem *virtadr;
+ struct docg4_priv *doc;
+ int len, retval;
+ struct resource *r;
+ struct device *dev = &pdev->dev;
+ const struct docg4_nand_platform_data *pdata = dev->platform_data;
+
+ if (pdata == NULL) {
+ dev_err(&pdev->dev, "no platform data!\n");
+ return -EINVAL;
+ }
+
+ r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (r == NULL) {
+ dev_err(dev, "no io memory resource defined!\n");
+ return -ENODEV;
+ }
+
+ virtadr = ioremap(r->start, resource_size(r));
+ if (!virtadr) {
+ dev_err(dev, "Diskonchip ioremap failed: "
+ "0x%x bytes at 0x%x\n",
+ resource_size(r), r->start);
+ return -EIO;
+ }
+
+ len = sizeof(struct mtd_info) + sizeof(struct nand_chip) +
+ sizeof(struct docg4_priv);
+ mtd = kzalloc(len, GFP_KERNEL);
+ if (mtd == NULL) {
+ retval = -ENOMEM;
+ goto fail;
+ }
+ nand = (struct nand_chip *) (mtd + 1);
+ doc = (struct docg4_priv *) (nand + 1);
+ mtd->priv = nand;
+ nand->priv = doc;
+ mtd->owner = THIS_MODULE;
+ doc->virtadr = virtadr;
+ doc->dev = dev;
+
+ init_mtd_structs(mtd);
+
+ /* initialize kernel bch algorithm */
+ doc->bch = init_bch(DOCG4_M, DOCG4_T, DOCG4_PRIMITIVE_POLY);
+ if (doc->bch == NULL) {
+ retval = -EINVAL;
+ goto fail;
+ }
+
+ platform_set_drvdata(pdev, doc);
+
+ reset(mtd, nand);
+ retval = read_id_reg(mtd, nand);
+ if (retval == -ENODEV) {
+ dev_warn(dev, "No diskonchip G4 device found.\n");
+ goto fail;
+ }
+
+ retval = nand_scan_tail(mtd);
+ if (retval)
+ goto fail;
+
+ retval = read_factory_bbt(mtd);
+ if (retval)
+ goto fail;
+
+ retval = mtd_device_register(mtd, NULL, 0);
+ if (retval)
+ goto fail;
+
+ if (pdata->nr_partitions > 0) {
+ int i;
+ for (i = 0; i < pdata->nr_partitions; i++)
+ pdata->partitions[i].ecclayout = &docg4_oobinfo;
+ retval = mtd_device_register(mtd, pdata->partitions,
+ pdata->nr_partitions);
+ }
+ if (retval)
+ goto fail;
+
+ doc->mtd = mtd;
+ return 0;
+
+ fail:
+ iounmap(virtadr);
+ if (mtd) {
+ /* re-declarations avoid compiler warning */
+ struct nand_chip *nand = mtd->priv;
+ struct docg4_priv *doc = nand->priv;
+ nand_release(mtd); /* deletes partitions and mtd devices */
+ platform_set_drvdata(pdev, NULL);
+ free_bch(doc->bch);
+ kfree(mtd);
+ }
+
+ return retval;
+}
+
+static int __exit cleanup_docg4(struct platform_device *pdev)
+{
+ struct docg4_priv *doc = platform_get_drvdata(pdev);
+ nand_release(doc->mtd);
+ iounmap(doc->virtadr);
+ platform_set_drvdata(pdev, NULL);
+ free_bch(doc->bch);
+ kfree(doc);
+ return 0;
+}
+
+static struct platform_driver docg4_driver = {
+ .driver = {
+ .name = "docg4",
+ .owner = THIS_MODULE,
+ },
+ .remove = __exit_p(cleanup_docg4),
+};
+
+static int __init docg4_init(void)
+{
+ return platform_driver_probe(&docg4_driver, probe_docg4);
+}
+
+static void __exit docg4_exit(void)
+{
+ platform_driver_unregister(&docg4_driver);
+}
+
+module_init(docg4_init);
+module_exit(docg4_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Mike Dunn");
+MODULE_DESCRIPTION("M-Systems DiskOnChip G4 device driver");
diff --git a/include/linux/mtd/docg4.h b/include/linux/mtd/docg4.h
new file mode 100644
index 0000000..654699c
--- /dev/null
+++ b/include/linux/mtd/docg4.h
@@ -0,0 +1,24 @@
+/*
+ * Copyright (C) 2011 Mike Dunn <mikedunn at newsguy.com>
+ *
+ * Nand mtd driver for M-Systems DiskOnChip G4 device
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+struct docg4_nand_platform_data {
+ struct mtd_partition *partitions;
+ unsigned int nr_partitions;
+};
--
1.7.3.4
More information about the linux-mtd
mailing list