[PATCH v2 2/2] davinci: Platform support for OMAP-L137/AM17x NOR flash driver

[Savinay Dharmappa]

Hi Sergei,

On Thu, Nov 18, 2010 at 17:22:26, Sergei Shtylyov wrote:
> Hello.
> 
> On 12-11-2010 11:02, Savinay Dharmappa wrote:
> 
> > From: Aleksey Makarov<amakarov at ru.mvista.com>
> 
> > Adds platform support for OMAP-L137/AM17x NOR flash driver.
> 
> > Also, configures chip select 3 to control NOR flash's upper
> > address lines.
> 
>     Please add back my signoff, omitted in this version. Some of the code,

> including bug fixes, was authored by me.
> 

I'll add your sign-off.

> > Signed-off-by: Aleksey Makarov <amakarov at ru.mvista.com>
> 
> Signed-off-by: Sergei Shtylyov <sshtylyov at ru.mvista.com>
> 
> > Signed-off-by: Savinay Dharmappa <savinay.dharmappa at ti.com>
> 
> > diff --git a/arch/arm/mach-davinci/board-da830-evm.c
b/arch/arm/mach-davinci/board-da830-evm.c
> > index 1bb89d3..cd35198 100644
> > --- a/arch/arm/mach-davinci/board-da830-evm.c
> > +++ b/arch/arm/mach-davinci/board-da830-evm.c
> [...]
> > @@ -429,6 +431,221 @@ static inline void da830_evm_init_nand(int
mux_mode)
> >   static inline void da830_evm_init_nand(int mux_mode) { }
> >   #endif
> >
> > +#ifdef CONFIG_DA830_UI_NOR
> > +/*
> > + * Number of Address line
> 
>     Only "lines".
> 

Ok.

> > going to the NOR flash that are latched using
> > + * AEMIF address lines  B_EMIF_BA0-B_EMIF_A12  on CS2.
> > +#define NOR_WINDOW_SIZE_LOG2     15
> > +#define NOR_WINDOW_SIZE         (1 << NOR_WINDOW_SIZE_LOG2)
> > +
> > +static struct {
> > +	struct clk *clk;
> > +	struct {
> > +		struct resource *res;
> 
>     You're not using this field outside da830_evm_nor_init() now, so
there's 
> not much point in keeping it...
> 

Ok. I'll use it as a local variable in da830_evm_nor_init().

> > +		void __iomem *addr;
> > +	} latch, aemif;
> > +} da830_evm_nor;
> 
> > +static void da830_evm_nor_set_window(unsigned long offset, void *data)
> > +{
> > +	/*
> > +	 * CS2 and CS3 address lines are used to address NOR flash. Address
> > +	 * line A0-A14 going to the NOR flash are latched using AEMIF
address
> > +	 * lines B_EMIF_BA0-B_EMIF_A12 on CS2.
> 
>     Are they really latched, and not just used live when the NOR chip is 
> accessed? What's the point of latching them?
> 

You are right. I'll correct the comment.

> > +static int da830_evm_nor_init(void *data, int cs)
> > +{
> > +	/* Turn on AEMIF clocks */
> > +	da830_evm_nor.clk = clk_get(NULL, "aemif");
> > +	if (IS_ERR(da830_evm_nor.clk)) {
> > +		pr_err("%s: could not get AEMIF clock\n", __func__);
> > +		da830_evm_nor.clk = NULL;
> > +		return -ENODEV;
> > +	}
> > +	clk_enable(da830_evm_nor.clk);
> > +
> > +	da830_evm_nor.aemif.res = request_mem_region(DA8XX_AEMIF_CTL_BASE,
> > +						     SZ_32K, "AEMIF
control");
> 
>     No need to store it -- you don't use it afterwards.
> 

Ok.

> > +	if (da830_evm_nor.aemif.res == NULL) {
> > +		pr_err("%s: could not request AEMIF control region\n",
> > +			__func__);
> > +		goto err_clk;
> > +	}
> 
> [...]
> 
> > +	/* Setup the window to access the latch */
> > +	da830_evm_nor.latch.res =
> > +		request_mem_region(DA8XX_AEMIF_CS3_BASE, PAGE_SIZE,
> > +				   "DA830 UI NOR address latch");
> 
>     Same comment here...
> 
> > +	if (da830_evm_nor.latch.res == NULL) {
> > +		pr_err("%s: could not request address latch region\n",
> > +			__func__);
> > +		goto err_aemif_ioremap;
> > +	}
> 
> [...]
> 
> > +static inline void da830_evm_init_nor(int mux_mode)
> > +{
> > +	int ret;
> > +
> > +	if (HAS_MMC) {
> > +		pr_warning("WARNING: both MMC/SD and NOR are "
> > +				"enabled, but they share AEMIF pins.\n"
> > +					"\tDisable MMC/SD for NOR
support.\n");
> 
>     This line is over-indented.

Ok. Will address your comments and send an updated an version

Thanks,
Savinay