[PATCH] mtd: pxa3xx_nand: unify prepare command
Lei Wen
leiwen at marvell.com
Mon Mar 22 00:04:22 EDT 2010
Make the interface simpler which could make both debug
and enhancement easier.
Signed-off-by: Lei Wen <leiwen at marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang at marvell.com>
---
drivers/mtd/nand/pxa3xx_nand.c | 256 +++++++++++++++++++++-------------------
1 files changed, 136 insertions(+), 120 deletions(-)
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 85de7f7..854adad 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -28,6 +28,7 @@
#define CHIP_DELAY_TIMEOUT (2 * HZ/10)
#define NAND_STOP_DELAY (2 * HZ/50)
+#define PAGE_CHUNK_SIZE (2048)
/* registers and bit definitions */
#define NDCR (0x00) /* Control register */
@@ -78,6 +79,7 @@
#define NDSR_RDDREQ (0x1 << 1)
#define NDSR_WRCMDREQ (0x1)
+#define NDCB0_ST_ROW_EN (0x1 << 26)
#define NDCB0_AUTO_RS (0x1 << 25)
#define NDCB0_CSEL (0x1 << 24)
#define NDCB0_CMD_TYPE_MASK (0x7 << 21)
@@ -334,7 +336,7 @@ static void pxa3xx_nand_start(struct pxa3xx_nand_info *info)
uint32_t ndcr;
ndcr = info->reg_ndcr;
- ndcr |= NDCR_ECC_EN;
+ ndcr |= info->use_ecc ? NDCR_ECC_EN : 0;
ndcr |= info->use_dma ? NDCR_DMA_EN : NDCR_STOP_ON_UNCOR;
ndcr |= NDCR_ND_RUN;
@@ -363,61 +365,6 @@ static void pxa3xx_nand_stop(struct pxa3xx_nand_info *info)
}
}
-static void prepare_read_prog_cmd(struct pxa3xx_nand_info *info,
- uint16_t cmd, int column, int page_addr)
-{
- pxa3xx_set_datasize(info);
-
- /* generate values for NDCBx registers */
- info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
- info->ndcb1 = 0;
- info->ndcb2 = 0;
- info->ndcb0 |= NDCB0_ADDR_CYC(info->row_addr_cycles + info->col_addr_cycles);
-
- if (info->col_addr_cycles == 2) {
- /* large block, 2 cycles for column address
- * row address starts from 3rd cycle
- */
- info->ndcb1 |= page_addr << 16;
- if (info->row_addr_cycles == 3)
- info->ndcb2 = (page_addr >> 16) & 0xff;
- } else
- /* small block, 1 cycles for column address
- * row address starts from 2nd cycle
- */
- info->ndcb1 = page_addr << 8;
-
- if (cmd == cmdset.program)
- info->ndcb0 |= NDCB0_CMD_TYPE(1) | NDCB0_AUTO_RS;
-}
-
-static void prepare_erase_cmd(struct pxa3xx_nand_info *info,
- uint16_t cmd, int page_addr)
-{
- info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
- info->ndcb0 |= NDCB0_CMD_TYPE(2) | NDCB0_AUTO_RS | NDCB0_ADDR_CYC(3);
- info->ndcb1 = page_addr;
- info->ndcb2 = 0;
-}
-
-static void prepare_other_cmd(struct pxa3xx_nand_info *info, uint16_t cmd)
-{
- info->ndcb0 = cmd | ((cmd & 0xff00) ? NDCB0_DBC : 0);
- info->ndcb1 = 0;
- info->ndcb2 = 0;
-
- if (cmd == cmdset.read_id) {
- info->ndcb0 |= NDCB0_CMD_TYPE(3);
- info->data_size = 8;
- } else if (cmd == cmdset.read_status) {
- info->ndcb0 |= NDCB0_CMD_TYPE(4);
- info->data_size = 8;
- } else if (cmd == cmdset.reset || cmd == cmdset.lock ||
- cmd == cmdset.unlock) {
- info->ndcb0 |= NDCB0_CMD_TYPE(5);
- }
-}
-
static void enable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
{
uint32_t ndcr;
@@ -555,94 +502,167 @@ static inline int is_buf_blank(uint8_t *buf, size_t len)
return 1;
}
-static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
- int column, int page_addr)
+static int prepare_command_pool(struct pxa3xx_nand_info *info, int command,
+ uint16_t column, int page_addr)
{
- struct pxa3xx_nand_info *info = mtd->priv;
- int ret, exec_cmd = 0;
+ uint16_t cmd;
+ int addr_cycle, exec_cmd, ndcb0;
+ struct mtd_info *mtd = info->mtd;
+
+ ndcb0 = 0;
+ addr_cycle = 0;
+ exec_cmd = 1;
- info->use_dma = (use_dma) ? 1 : 0;
- info->use_ecc = 0;
- info->data_size = 0;
- info->state = 0;
+ /* reset data and oob column point to handle data */
+ info->buf_start = 0;
+ info->buf_count = 0;
+ info->oob_size = 0;
+ info->use_ecc = 0;
switch (command) {
+ case NAND_CMD_READ0:
+ case NAND_CMD_PAGEPROG:
+ info->use_ecc = 1;
case NAND_CMD_READOOB:
- /* disable HW ECC to get all the OOB data */
- info->buf_count = mtd->writesize + mtd->oobsize;
- info->buf_start = mtd->writesize + column;
- memset(info->data_buff, 0xFF, info->buf_count);
+ pxa3xx_set_datasize(info);
+ break;
+ case NAND_CMD_SEQIN:
+ exec_cmd = 0;
+ break;
+ default:
+ info->ndcb1 = 0;
+ info->ndcb2 = 0;
+ break;
+ }
- prepare_read_prog_cmd(info, cmdset.read1, column, page_addr);
+ info->ndcb0 = ndcb0;
+ addr_cycle = NDCB0_ADDR_CYC(info->row_addr_cycles
+ + info->col_addr_cycles);
- /* We only are OOB, so if the data has error, does not matter */
- if (info->retcode == ERR_DBERR)
- info->retcode = ERR_NONE;
+ switch (command) {
+ case NAND_CMD_READOOB:
+ case NAND_CMD_READ0:
- exec_cmd = 1;
- break;
+ cmd = cmdset.read1;
+ if (command == NAND_CMD_READOOB)
+ info->buf_start = mtd->writesize + column;
+ else
+ info->buf_start = column;
+
+ if (unlikely(info->page_size < PAGE_CHUNK_SIZE))
+ info->ndcb0 |= NDCB0_CMD_TYPE(0)
+ | addr_cycle
+ | (cmd & NDCB0_CMD1_MASK);
+ else
+ info->ndcb0 |= NDCB0_CMD_TYPE(0)
+ | NDCB0_DBC
+ | addr_cycle
+ | cmd;
- case NAND_CMD_READ0:
- info->use_ecc = 1;
- info->retcode = ERR_NONE;
- info->buf_start = column;
- info->buf_count = mtd->writesize + mtd->oobsize;
- memset(info->data_buff, 0xFF, info->buf_count);
+ case NAND_CMD_SEQIN:
+ /* small page addr setting */
+ if (unlikely(info->page_size < PAGE_CHUNK_SIZE)) {
+ info->ndcb1 = ((page_addr & 0xFFFFFF) << 8)
+ | (column & 0xFF);
- prepare_read_prog_cmd(info, cmdset.read1, column, page_addr);
- if (info->retcode == ERR_DBERR) {
- /* for blank page (all 0xff), HW will calculate its ECC as
- * 0, which is different from the ECC information within
- * OOB, ignore such double bit errors
- */
- if (is_buf_blank(info->data_buff, mtd->writesize))
- info->retcode = ERR_NONE;
+ info->ndcb2 = 0;
+ }
+ else {
+ info->ndcb1 = ((page_addr & 0xFFFF) << 16)
+ | (column & 0xFFFF);
+
+ if (page_addr & 0xFF0000)
+ info->ndcb2 = (page_addr & 0xFF0000) >> 16;
+ else
+ info->ndcb2 = 0;
}
- exec_cmd = 1;
- break;
- case NAND_CMD_SEQIN:
- info->buf_start = column;
info->buf_count = mtd->writesize + mtd->oobsize;
- memset(info->data_buff, 0xff, info->buf_count);
+ memset(info->data_buff, 0xFF, info->buf_count);
- /* save column/page_addr for next CMD_PAGEPROG */
- info->seqin_column = column;
- info->seqin_page_addr = page_addr;
break;
+
case NAND_CMD_PAGEPROG:
- info->use_ecc = (info->seqin_column >= mtd->writesize) ? 0 : 1;
+ if (is_buf_blank(info->data_buff, (mtd->writesize + mtd->oobsize))) {
+ exec_cmd = 0;
+ break;
+ }
- prepare_read_prog_cmd(info, cmdset.program,
- info->seqin_column, info->seqin_page_addr);
+ cmd = cmdset.program;
info->state |= STATE_IS_WRITE;
- exec_cmd = 1;
- break;
- case NAND_CMD_ERASE1:
- prepare_erase_cmd(info, cmdset.erase, page_addr);
- exec_cmd = 1;
- case NAND_CMD_ERASE2:
+ info->ndcb0 |= NDCB0_CMD_TYPE(0x1)
+ | NDCB0_AUTO_RS
+ | NDCB0_ST_ROW_EN
+ | NDCB0_DBC
+ | cmd
+ | addr_cycle;
break;
+
case NAND_CMD_READID:
+ cmd = cmdset.read_id;
+ info->buf_count = info->read_id_bytes;
+ info->ndcb0 |= NDCB0_CMD_TYPE(3)
+ | NDCB0_ADDR_CYC(1)
+ | cmd;
+
+ info->data_size = 8;
+ break;
+
case NAND_CMD_STATUS:
- info->use_dma = 0; /* force PIO read */
- info->buf_start = 0;
- info->buf_count = (command == NAND_CMD_READID) ?
- info->read_id_bytes : 1;
-
- prepare_other_cmd(info, (command == NAND_CMD_READID) ?
- cmdset.read_id : cmdset.read_status);
- exec_cmd = 1;
+ cmd = cmdset.read_status;
+ info->buf_count = 1;
+ info->ndcb0 |= NDCB0_CMD_TYPE(4)
+ | NDCB0_ADDR_CYC(1)
+ | cmd;
+
+ info->data_size = 8;
+ break;
+
+ case NAND_CMD_ERASE1:
+ cmd = cmdset.erase;
+ info->ndcb0 |= NDCB0_CMD_TYPE(2)
+ | NDCB0_AUTO_RS
+ | NDCB0_ADDR_CYC(3)
+ | NDCB0_DBC
+ | cmd;
+ info->ndcb1 = page_addr;
+ info->ndcb2 = 0;
+
break;
case NAND_CMD_RESET:
- prepare_other_cmd(info, cmdset.reset);
- exec_cmd = 1;
+ cmd = cmdset.reset;
+ info->ndcb0 |= NDCB0_CMD_TYPE(5)
+ | cmd;
+
break;
+
+ case NAND_CMD_ERASE2:
+ exec_cmd = 0;
+ break;
+
default:
- printk(KERN_ERR "non-supported command.\n");
+ exec_cmd = 0;
+ printk(KERN_ERR "pxa3xx-nand: non-supported command %x\n", command);
break;
}
+ return exec_cmd;
+}
+
+static void pxa3xx_nand_cmdfunc(struct mtd_info *mtd, unsigned command,
+ int column, int page_addr)
+{
+ struct pxa3xx_nand_info *info = mtd->priv;
+ int ret, exec_cmd;
+
+ /* if this is a x16 device ,then convert the input
+ * "byte" address into a "word" address appropriate
+ * for indexing a word-oriented device
+ */
+ if (info->reg_ndcr & NDCR_DWIDTH_M)
+ column /= 2;
+
+ exec_cmd = prepare_command_pool(info, command, column, page_addr);
if (exec_cmd) {
init_completion(&info->cmd_complete);
info->state |= STATE_CMD_PREPARED;
@@ -657,10 +677,6 @@ static void pxa3xx_nand_cmdfunc(struct mtd_info
*mtd, unsigned command,
pxa3xx_nand_stop(info);
disable_int(info, NDCR_INT_MASK);
info->state &= ~STATE_CMD_PREPARED;
- if (info->retcode == ERR_DBERR) {
- printk(KERN_ERR "double bit error @ page %08x\n", page_addr);
- info->retcode = ERR_NONE;
- }
}
}
--
1.5.6.5
More information about the linux-mtd
mailing list