[PATCH v3 4/4] omap: nand: making ecc layout as compatible with romcode ecc

[Sukumar Ghorai]

    This patch overrides nand ecc layout and bad block descriptor (for 8-bit
    device) to support hw ecc in romcode layout. So as to have in sync with ecc
    layout throughout; i.e. x-laod, u-boot and kernel.

    This patch also enables to use romcode ecc for spd and zoom, by default.

    This enables to flash x-load, u-boot, kernel, FS images from kernel itself
    and compatiable with other tools.

Signed-off-by: Sukumar Ghorai <s-ghorai at ti.com>
Signed-off-by: Vimal Singh <vimalsingh at ti.com>
---
 arch/arm/mach-omap2/board-flash.c |    2 +-
 drivers/mtd/nand/omap2.c          |   34 ++++++++++++++++++++++++++++++++++
 2 files changed, 35 insertions(+), 1 deletions(-)

diff --git a/arch/arm/mach-omap2/board-flash.c b/arch/arm/mach-omap2/board-flash.c
index ab31e7f..a15aab6 100644
--- a/arch/arm/mach-omap2/board-flash.c
+++ b/arch/arm/mach-omap2/board-flash.c
@@ -144,7 +144,7 @@ __init board_nand_init(struct mtd_partition *nand_parts, u8 nr_parts, u8 cs)
 	board_nand_data.cs		= cs;
 	board_nand_data.parts		= nand_parts;
 	board_nand_data.nr_parts	= nr_parts;
-	board_nand_data.ecc_opt		= OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT;
+	board_nand_data.ecc_opt		= OMAP_ECC_HAMMING_CODE_HW;
 
 	gpmc_nand_init(&board_nand_data);
 }
diff --git a/drivers/mtd/nand/omap2.c b/drivers/mtd/nand/omap2.c
index 0464a19..09b26d7 100644
--- a/drivers/mtd/nand/omap2.c
+++ b/drivers/mtd/nand/omap2.c
@@ -128,6 +128,20 @@ const int use_dma;
 const int use_interrupt;
 #endif
 
+/* oob info generated runtime depending on ecc algorithm and layout selected */
+static struct nand_ecclayout omap_oobinfo;
+/* Define some generic bad / good block scan pattern which are used
+ * while scanning a device for factory marked good / bad blocks
+ */
+static uint8_t scan_ff_pattern[] = { 0xff };
+static struct nand_bbt_descr bb_descrip_flashbased = {
+	.options = NAND_BBT_SCANEMPTY | NAND_BBT_SCANALLPAGES,
+	.offs = 0,
+	.len = 1,
+	.pattern = scan_ff_pattern,
+};
+
+
 struct omap_nand_info {
 	struct nand_hw_control		controller;
 	struct omap_nand_platform_data	*pdata;
@@ -945,6 +959,7 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
 	struct omap_nand_info		*info;
 	struct omap_nand_platform_data	*pdata;
 	int				err;
+	int				i, offset;
 
 	pdata = pdev->dev.platform_data;
 	if (pdata == NULL) {
@@ -1079,6 +1094,25 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
 		}
 	}
 
+	/* rom code layout */
+	if (pdata->ecc_opt != OMAP_ECC_HAMMING_CODE_DIFF_LAYOUT) {
+		offset = (info->nand.options & NAND_BUSWIDTH_16) ? 2 : 1;
+		if (info->mtd.oobsize == 16) {
+			info->nand.badblock_pattern = &bb_descrip_flashbased;
+			omap_oobinfo.eccbytes = 3;
+		} else
+			omap_oobinfo.eccbytes  = 3 * 4;
+
+		for (i = 0; i < omap_oobinfo.eccbytes; i++)
+			omap_oobinfo.eccpos[i] = i+offset;
+
+		omap_oobinfo.oobfree->offset = offset + omap_oobinfo.eccbytes;
+		omap_oobinfo.oobfree->length = info->mtd.oobsize -
+					(offset + omap_oobinfo.eccbytes);
+
+		info->nand.ecc.layout = &omap_oobinfo;
+	}
+
 #ifdef CONFIG_MTD_PARTITIONS
 	err = parse_mtd_partitions(&info->mtd, part_probes, &info->parts, 0);
 	if (err > 0)