[PATCH try#2] [MTD/MAPS] Blackfin BF5xx Maps: Handle the case where flash memory and ethernet mac/phy are mapped onto the same async bank
Bryan Wu
cooloney at kernel.org
Mon May 12 03:24:29 EDT 2008
Hi David and Will,
Is this patch OK for you? Thanks a lot
Regards,
-Bryan
On Sun, Feb 3, 2008 at 2:32 PM, Bryan Wu <bryan.wu at analog.com> wrote:
> >From 974192a0bf168e84370377b835a2858948789088 Mon Sep 17 00:00:00 2001
> From: Bryan Wu <bryan.wu at analog.com>
> Date: Sun, 3 Feb 2008 14:27:09 +0800
> Subject: [PATCH] [MTD/MAPS] Blackfin BF5xx Maps: Handle the case where flash memory and ethernet mac/phy are mapped onto the same async bank
>
> [try #1]
> The BF533-STAMP does this for example.
> All board-specific configuration goes in your board resources file.
>
> [try #2]
> Remove useless SSYNC() as Will said
>
> Signed-off-by: Mike Frysinger <michael.frysinger at analog.com>
> Signed-off-by: Bryan Wu <bryan.wu at analog.com>
> ---
> drivers/mtd/maps/Kconfig | 45 ++++++++
> drivers/mtd/maps/Makefile | 1 +
> drivers/mtd/maps/bf5xx-flash.c | 227 ++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 273 insertions(+), 0 deletions(-)
> create mode 100644 drivers/mtd/maps/bf5xx-flash.c
>
> diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
> index a592fc0..5357f04 100644
> --- a/drivers/mtd/maps/Kconfig
> +++ b/drivers/mtd/maps/Kconfig
> @@ -528,6 +528,51 @@ config MTD_PCMCIA_ANONYMOUS
>
> If unsure, say N.
>
> +config MTD_BF5xx
> + tristate "Blackfin BF533-STAMP Flash Chip Support"
> + depends on BFIN533_STAMP && MTD_CFI
> + select MTD_PARTITIONS
> + help
> + Map driver which allows for simultaneous utilization of
> + ethernet and CFI parallel flash.
> +
> +config BFIN_FLASH_BANK_0
> + hex "EBIU_AMBCTL For Flash (Bank 0)"
> + depends on MTD_BF5xx
> + default 0x7BB0
> + help
> + For boards that share the async memory bank with both Flash and
> + the Ethernet, these settings allow you to have EBIU settings just
> + when the Flash is active. The other EBIU settings in the main
> + Blackfin menu will be utilized when the Flash is not active.
> +config BFIN_FLASH_BANK_1
> + hex "EBIU_AMBCTL For Flash (Bank 1)"
> + depends on MTD_BF5xx
> + default 0x7BB0
> + help
> + For boards that share the async memory bank with both Flash and
> + the Ethernet, these settings allow you to have EBIU settings just
> + when the Flash is active. The other EBIU settings in the main
> + Blackfin menu will be utilized when the Flash is not active.
> +config BFIN_FLASH_BANK_2
> + hex "EBIU_AMBCTL For Flash (Bank 2)"
> + depends on MTD_BF5xx
> + default 0x7BB0
> + help
> + For boards that share the async memory bank with both Flash and
> + the Ethernet, these settings allow you to have EBIU settings just
> + when the Flash is active. The other EBIU settings in the main
> + Blackfin menu will be utilized when the Flash is not active.
> +config BFIN_FLASH_BANK_3
> + hex "EBIU_AMBCTL For Flash (Bank 3)"
> + depends on MTD_BF5xx
> + default 0x7BB0
> + help
> + For boards that share the async memory bank with both Flash and
> + the Ethernet, these settings allow you to have EBIU settings just
> + when the Flash is active. The other EBIU settings in the main
> + Blackfin menu will be utilized when the Flash is not active.
> +
> config MTD_UCLINUX
> tristate "Generic uClinux RAM/ROM filesystem support"
> depends on MTD_PARTITIONS && !MMU
> diff --git a/drivers/mtd/maps/Makefile b/drivers/mtd/maps/Makefile
> index 316382a..62eea4f 100644
> --- a/drivers/mtd/maps/Makefile
> +++ b/drivers/mtd/maps/Makefile
> @@ -69,3 +69,4 @@ obj-$(CONFIG_MTD_PLATRAM) += plat-ram.o
> obj-$(CONFIG_MTD_OMAP_NOR) += omap_nor.o
> obj-$(CONFIG_MTD_MTX1) += mtx-1_flash.o
> obj-$(CONFIG_MTD_INTEL_VR_NOR) += intel_vr_nor.o
> +obj-$(CONFIG_MTD_BF5xx) += bf5xx-flash.o
> diff --git a/drivers/mtd/maps/bf5xx-flash.c b/drivers/mtd/maps/bf5xx-flash.c
> new file mode 100644
> index 0000000..dec02e2
> --- /dev/null
> +++ b/drivers/mtd/maps/bf5xx-flash.c
> @@ -0,0 +1,227 @@
> +/*
> + * drivers/mtd/maps/bf5xx-flash.c
> + *
> + * Handle the case where flash memory and ethernet mac/phy are
> + * mapped onto the same async bank. The BF533-STAMP does this
> + * for example. All board-specific configuration goes in your
> + * board resources file.
> + *
> + * Copyright 2000 Nicolas Pitre <nico at cam.org>
> + * Copyright 2005-2008 Analog Devices Inc.
> + *
> + * Enter bugs at http://blackfin.uclinux.org/
> + *
> + * Licensed under the GPL-2 or later.
> + */
> +
> +#include <linux/init.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/mtd/mtd.h>
> +#include <linux/mtd/map.h>
> +#include <linux/mtd/partitions.h>
> +#include <linux/mtd/physmap.h>
> +#include <linux/platform_device.h>
> +#include <linux/types.h>
> +
> +#include <asm/blackfin.h>
> +#include <asm/gpio.h>
> +#include <asm/io.h>
> +#include <asm/unaligned.h>
> +
> +#define pr_init(fmt, args...) ({ static const __initdata char __fmt[] = fmt; printk(__fmt, ## args); })
> +
> +#define DRIVER_NAME "BF5xx-Flash"
> +
> +#define BFIN_FLASH_AMBCTL0VAL ((CONFIG_BFIN_FLASH_BANK_1 << 16) | CONFIG_BFIN_FLASH_BANK_0)
> +#define BFIN_FLASH_AMBCTL1VAL ((CONFIG_BFIN_FLASH_BANK_3 << 16) | CONFIG_BFIN_FLASH_BANK_2)
> +
> +/* Should add a per-device structure and track this there ... */
> +static int enet_flash_pin;
> +static struct mtd_info *bf5xx_mtd;
> +
> +struct flash_save {
> + u32 ambctl0;
> + u32 ambctl1;
> + unsigned long flags;
> +};
> +
> +static void switch_to_flash(struct flash_save *save)
> +{
> + local_irq_save(save->flags);
> +
> + gpio_set_value(enet_flash_pin, 0);
> +
> + save->ambctl0 = bfin_read_EBIU_AMBCTL0();
> + save->ambctl1 = bfin_read_EBIU_AMBCTL1();
> + bfin_write_EBIU_AMBCTL0(BFIN_FLASH_AMBCTL0VAL);
> + bfin_write_EBIU_AMBCTL1(BFIN_FLASH_AMBCTL1VAL);
> + SSYNC();
> +}
> +
> +static void switch_back(struct flash_save *save)
> +{
> + bfin_write_EBIU_AMBCTL0(save->ambctl0);
> + bfin_write_EBIU_AMBCTL1(save->ambctl1);
> + SSYNC();
> +
> + gpio_set_value(enet_flash_pin, 1);
> +
> + local_irq_restore(save->flags);
> +}
> +
> +static map_word bf5xx_read(struct map_info *map, unsigned long ofs)
> +{
> + int nValue = 0x0;
> + map_word test;
> + struct flash_save save;
> +
> + switch_to_flash(&save);
> +
> + nValue = readw(map->virt + ofs);
> + SSYNC();
> +
> + switch_back(&save);
> +
> + test.x[0] = (u16)nValue;
> + return test;
> +}
> +
> +static void bf5xx_copy_from(struct map_info *map, void *to, unsigned long from, ssize_t len)
> +{
> + unsigned long i;
> + map_word test;
> +
> + if ((unsigned long)to & 0x1) {
> + for (i = 0; i < len / 2 * 2; i += 2) {
> + test = bf5xx_read(map, from + i);
> + put_unaligned(test.x[0], (__le16 *)(to + i));
> + }
> + } else {
> + for (i = 0; i < len / 2 * 2; i += 2) {
> + test = bf5xx_read(map, from + i);
> + *((u16*)(to + i)) = test.x[0];
> + }
> + }
> +
> + if (len & 0x1) {
> + test = bf5xx_read(map, from + i);
> + *((u8*)(to + i)) = (u8)test.x[0];
> + }
> +}
> +
> +static void bf5xx_write(struct map_info *map, map_word d1, unsigned long ofs)
> +{
> + u16 d;
> + struct flash_save save;
> +
> + d = (u16)d1.x[0];
> +
> + switch_to_flash(&save);
> +
> + writew(d, map->virt + ofs);
> + SSYNC();
> +
> + switch_back(&save);
> +}
> +
> +static void bf5xx_copy_to(struct map_info *map, unsigned long to, const void *from, ssize_t len)
> +{
> + struct flash_save save;
> +
> + switch_to_flash(&save);
> +
> + memcpy(map->virt + to, from, len);
> + SSYNC();
> +
> + switch_back(&save);
> +}
> +
> +static struct map_info bf5xx_map = {
> + .name = DRIVER_NAME,
> + .read = bf5xx_read,
> + .copy_from = bf5xx_copy_from,
> + .write = bf5xx_write,
> + .copy_to = bf5xx_copy_to,
> +};
> +
> +#ifdef CONFIG_MTD_PARTITIONS
> +static const char *part_probe_types[] = { "cmdlinepart", "RedBoot", NULL };
> +#endif
> +
> +static int __init bf5xx_flash_probe(struct platform_device *dev)
> +{
> + int ret;
> + struct physmap_flash_data *pdata = dev->dev.platform_data;
> + struct resource *memory = platform_get_resource(dev, IORESOURCE_MEM, 0);
> +
> + enet_flash_pin = platform_get_irq(dev, 0);
> +
> + bf5xx_map.bankwidth = pdata->width;
> + bf5xx_map.size = memory->end - memory->start + 1;
> + bf5xx_map.virt = (void __iomem *)memory->start;
> + bf5xx_map.phys = memory->start;
> +
> + if (gpio_request(enet_flash_pin, DRIVER_NAME)) {
> + pr_init(KERN_ERR DRIVER_NAME ": Failed to request gpio %d\n", enet_flash_pin);
> + return -EBUSY;
> + }
> + gpio_direction_output(enet_flash_pin, 1);
> +
> + pr_init(KERN_NOTICE DRIVER_NAME ": probing %d-bit flash bus\n", bf5xx_map.bankwidth * 8);
> + bf5xx_mtd = do_map_probe(memory->name, &bf5xx_map);
> + if (!bf5xx_mtd)
> + return -ENXIO;
> +
> +#ifdef CONFIG_MTD_PARTITIONS
> + ret = parse_mtd_partitions(bf5xx_mtd, part_probe_types, &pdata->parts, 0);
> + if (ret > 0) {
> + pr_init(KERN_NOTICE DRIVER_NAME ": Using commandline partition definition\n");
> + add_mtd_partitions(bf5xx_mtd, pdata->parts, ret);
> +
> + } else if (pdata->nr_parts) {
> + pr_init(KERN_NOTICE DRIVER_NAME ": Using board partition definition\n");
> + add_mtd_partitions(bf5xx_mtd, pdata->parts, pdata->nr_parts);
> +
> + } else
> +#endif
> + {
> + pr_init(KERN_NOTICE DRIVER_NAME ": no partition info available, registering whole flash at once\n");
> + add_mtd_device(bf5xx_mtd);
> + }
> +
> + return 0;
> +}
> +
> +static int __devexit bf5xx_flash_remove(struct platform_device *dev)
> +{
> + gpio_free(enet_flash_pin);
> +#ifdef CONFIG_MTD_PARTITIONS
> + del_mtd_partitions(bf5xx_mtd);
> +#endif
> + map_destroy(bf5xx_mtd);
> + return 0;
> +}
> +
> +static struct platform_driver bf5xx_flash_driver = {
> + .probe = bf5xx_flash_probe,
> + .remove = __devexit_p(bf5xx_flash_remove),
> + .driver = {
> + .name = DRIVER_NAME,
> + },
> +};
> +
> +static int __init bf5xx_flash_init(void)
> +{
> + return platform_driver_register(&bf5xx_flash_driver);
> +}
> +module_init(bf5xx_flash_init);
> +
> +static void __exit bf5xx_flash_exit(void)
> +{
> + platform_driver_unregister(&bf5xx_flash_driver);
> +}
> +module_exit(bf5xx_flash_exit);
> +
> +MODULE_LICENSE("GPL");
> +MODULE_DESCRIPTION("MTD map driver for Blackfins with flash/ethernet on same async bank");
> --
> 1.5.3.4
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
>
More information about the linux-mtd
mailing list