JFFS2 mount problem on NAND flash

Sameer x0081444 at ti.com
Thu Jan 3 08:22:29 EST 2008


Hi,
I am working on omap based board with 16bit, small page Samsung NAND of size 64MB.
I have enabled hardware ecc functionality in the driver code. To test the functionality I run the
Following tests.
1. When the kernel comes up, >>cat /proc/mtd
	mtd0: 00040000 00020000 "bootloader"
	mtd1: 00020000 00020000 "params"
	mtd2: 00200000 00020000 "kernel"
	mtd3: 03da0000 00020000 "filesystem"
	mtd4: 00080000 00004000 "NAND-X-Loader"
	mtd5: 00080000 00004000 "NAND-U-Boot"
	mtd6: 00040000 00004000 "NAND-U-Boot Environment"
	mtd7: 00400000 00004000 "NAND-Kernel"
	mtd8: 03ac0000 00004000 "NAND-File System"
2. I erase the NAND flash filesystem partition
	./flash_eraseall /dev/mtd8
	This function passes. I have verified the erase functionality using the debugger.
3  mount -t jffs2 /dev/mtdblock8 /mnt/nand. I have enabled the low level jffs2 fs debugging
	Following is the error message
			
	JFFS2: Erase block at 0x00000000 is not formatted. It will be erased
	JFFS2: Erase block at 0x00004000 is not formatted. It will be erased
	JFFS2: Erase block at 0x00008000 is not formatted. It will be erased
	JFFS2: Erase block at 0x0000c000 is not formatted. It will be erased
	JFFS2: Erase block at 0x00010000 is not formatted. It will be erased
	JFFS2: Erase block at 0x00014000 is not formatted. It will be erased
	JFFS2: Erase block at 0x00018000 is not formatted. It will be erased
	JFFS2: Erase block at 0x0001c000 is not formatted. It will be erased
					     -----
						=----
					upto--

	JFFS2: Erase block at 0x03a9c000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03aa0000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03aa4000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03aa8000 is not formatted. It will be erased
	FFS2: Erase block at 0x03aac000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03ab0000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03ab4000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03ab8000 is not formatted. It will be erased
	JFFS2: Erase block at 0x03abc000 is not formatted. It will be erased
	Cowardly refusing to erase blocks on filesystem with no valid JFFS2 nodes
	mpty_blocks 0, bad_blocks 0, c->nr_blocks 3760
	mount: Mounting /dev/mtdblock8 on /mnt/nand failed: Input/output error

But when I enable the SW_ECC functionalilty I am able to mount the jffs2 fs and perform the fs operations

I am beginner for JFFS2 fs.Could you please let me know what causes this error.


Regards,
-Sameer




More information about the linux-mtd mailing list