MTD kobject warnings due to block layer changes

[Manuel Lauss]

Hello,

Todays -git spits out these wanings during boot, caused by
Commit abf5439370491dd6fbb4fe1a7939680d2a9bc9d4
( block: move cmdfilter from gendisk to request_queue ):

Using physmap partition information
Creating 3 MTD partitions on "physmap-flash":
0x00000000-0x01c00000 : "User FS"
0x01c00000-0x01c40000 : "booter"
kobject (8511c410): tried to init an initialized object, something is seriously wrong.
Call Trace:
[<8036644c>] dump_stack+0x8/0x34
[<8021f050>] kobject_init+0x50/0xcc
[<8021fa18>] kobject_init_and_add+0x24/0x58
[<8021d20c>] blk_register_filter+0x4c/0x64
[<8021c194>] add_disk+0x78/0xe0
[<8027d14c>] add_mtd_blktrans_dev+0x254/0x278
[<8027c8f0>] blktrans_notify_add+0x40/0x78
[<80279c00>] add_mtd_device+0xd0/0x150
[<8027b090>] add_mtd_partitions+0x568/0x5d8
[<80285458>] physmap_flash_probe+0x2ac/0x334
[<802644f8>] driver_probe_device+0x12c/0x244
[<8026465c>] __driver_attach+0x4c/0x84
[<80263c64>] bus_for_each_dev+0x58/0xac
[<802633ec>] bus_add_driver+0xc4/0x24c
[<802648e0>] driver_register+0xcc/0x184
[<80100460>] _stext+0x60/0x1bc

0x01c40000-0x01fe0000 : "vmlinux.elf"
kobject (8511c410): tried to init an initialized object, something is seriously wrong.
Call Trace:
[<8036644c>] dump_stack+0x8/0x34
[<8021f050>] kobject_init+0x50/0xcc
[<8021fa18>] kobject_init_and_add+0x24/0x58
[<8021d20c>] blk_register_filter+0x4c/0x64
[<8021c194>] add_disk+0x78/0xe0
[<8027d14c>] add_mtd_blktrans_dev+0x254/0x278
[<8027c8f0>] blktrans_notify_add+0x40/0x78
[<80279c00>] add_mtd_device+0xd0/0x150
[<8027b090>] add_mtd_partitions+0x568/0x5d8
[<80285458>] physmap_flash_probe+0x2ac/0x334
[<802644f8>] driver_probe_device+0x12c/0x244
[<8026465c>] __driver_attach+0x4c/0x84
[<80263c64>] bus_for_each_dev+0x58/0xac
[<802633ec>] bus_add_driver+0xc4/0x24c
[<802648e0>] driver_register+0xcc/0x184
[<80100460>] _stext+0x60/0x1bc

NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 1 MTD partitions on "gen_nand":
0x00000000-0x08000000 : "NAND FS 0"
kobject (8511c410): tried to init an initialized object, something is seriously wrong.
Call Trace:
[<8036644c>] dump_stack+0x8/0x34
[<8021f050>] kobject_init+0x50/0xcc
[<8021fa18>] kobject_init_and_add+0x24/0x58
[<8021d20c>] blk_register_filter+0x4c/0x64
[<8021c194>] add_disk+0x78/0xe0
[<8027d14c>] add_mtd_blktrans_dev+0x254/0x278
[<8027c8f0>] blktrans_notify_add+0x40/0x78
[<80279c00>] add_mtd_device+0xd0/0x150
[<8027b090>] add_mtd_partitions+0x568/0x5d8
[<804016b0>] plat_nand_probe+0x1e8/0x24c
[<802644f8>] driver_probe_device+0x12c/0x244
[<8026465c>] __driver_attach+0x4c/0x84
[<80263c64>] bus_for_each_dev+0x58/0xac
[<802633ec>] bus_add_driver+0xc4/0x24c
[<802648e0>] driver_register+0xcc/0x184
[<80100460>] _stext+0x60/0x1bc


Thanks!
	Manuel Lauss