OneNAND: interrupt based wait support (for reference)

Kyungmin Park kyungmin.park at samsung.com
Fri Nov 3 04:29:22 EST 2006


Hi,

The previous mail has some problem. So I send it again.

Here's full referenece code against mtd tree.

Just reference to apollon source. Apollon patch will be sent to omap mailing list.

Please apply the previous patch. :)

Thank you,
Kyungmin Park

--


diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index 03d6905..e181945 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -24,6 +24,7 @@ #include <linux/mtd/partitions.h>
 #include <linux/mtd/onenand.h>
 #include <linux/interrupt.h>
 #include <linux/delay.h>
+#include <linux/irq.h>
 
 #include <asm/hardware.h>
 #include <asm/mach-types.h>
@@ -45,6 +46,8 @@ #define SW_ENTER_GPIO16		16
 #define SW_UP_GPIO17		17
 #define SW_DOWN_GPIO58		58
 
+#define APOLLON_FLASH_GPIO_IRQ	72
+
 static struct mtd_partition apollon_partitions[] = {
 	{
 		.name		= "X-Loader + U-Boot",
@@ -84,10 +87,17 @@ static struct flash_platform_data apollo
 	.nr_parts	= ARRAY_SIZE(apollon_partitions),
 };
 
-static struct resource apollon_flash_resource = {
-	.start		= APOLLON_CS0_BASE,
-	.end		= APOLLON_CS0_BASE + SZ_128K,
-	.flags		= IORESOURCE_MEM,
+static struct resource apollon_flash_resource[] = {
+	[0] = {
+		.start	= APOLLON_CS0_BASE,
+		.end	= APOLLON_CS0_BASE + SZ_128K,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= OMAP_GPIO_IRQ(APOLLON_FLASH_GPIO_IRQ),
+		.end	= OMAP_GPIO_IRQ(APOLLON_FLASH_GPIO_IRQ),
+		.flags	= IORESOURCE_IRQ,
+	},
 };
 
 static struct platform_device apollon_onenand_device = {
@@ -96,8 +106,8 @@ static struct platform_device apollon_on
 	.dev		= {
 		.platform_data	= &apollon_flash_data,
 	},
-	.num_resources	= ARRAY_SIZE(&apollon_flash_resource),
-	.resource	= &apollon_flash_resource,
+	.num_resources	= ARRAY_SIZE(apollon_flash_resource),
+	.resource	= apollon_flash_resource,
 };
 
 static struct resource apollon_smc91x_resources[] = {
@@ -152,12 +162,24 @@ static inline void __init apollon_init_s
 	omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);
 }
 
+static inline void __init apollon_init_flash(void)
+{
+	if (omap_request_gpio(APOLLON_FLASH_GPIO_IRQ) < 0) {
+		printk(KERN_ERR "Failed to request GPIO%d for onenand IRQ\n",
+			APOLLON_FLASH_GPIO_IRQ);
+		return;
+	}
+	omap_set_gpio_direction(APOLLON_FLASH_GPIO_IRQ, 1);
+	set_irq_type(OMAP_GPIO_IRQ(APOLLON_FLASH_GPIO_IRQ), IRQT_RISING);
+}
+
 static void __init omap_apollon_init_irq(void)
 {
 	omap2_init_common_hw();
 	omap_init_irq();
 	omap_gpio_init();
 	apollon_init_smc91x();
+	apollon_init_flash();
 }
 
 static struct omap_uart_config apollon_uart_config __initdata = {
diff --git a/drivers/mtd/onenand/generic.c b/drivers/mtd/onenand/generic.c
index af06a80..cdf80c6 100644
--- a/drivers/mtd/onenand/generic.c
+++ b/drivers/mtd/onenand/generic.c
@@ -63,6 +63,7 @@ static int __devinit generic_onenand_pro
 	}
 
 	info->onenand.mmcontrol = pdata->mmcontrol;
+	info->onenand.irq = platform_get_irq(pdev, 0);
 
 	info->mtd.name = pdev->dev.bus_id;
 	info->mtd.priv = &info->onenand;
diff --git a/drivers/mtd/onenand/onenand_base.c b/drivers/mtd/onenand/onenand_base.c
index 8ed68b2..aea13a3 100644
--- a/drivers/mtd/onenand/onenand_base.c
+++ b/drivers/mtd/onenand/onenand_base.c
@@ -13,6 +13,7 @@ #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/init.h>
 #include <linux/sched.h>
+#include <linux/interrupt.h>
 #include <linux/jiffies.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/onenand.h>
@@ -339,6 +340,111 @@ static int onenand_wait(struct mtd_info 
 	return 0;
 }
 
+/*
+ * onenand_interrupt - [DEFAULT] onenand interrupt handler
+ * @param irq		onenand interrupt number
+ * @param dev_id	interrupt data
+ *
+ * complete the work
+ */
+static irqreturn_t onenand_interrupt(int irq, void *data)
+{
+	struct onenand_chip *this = (struct onenand_chip *) data;
+
+	/* To handle shared interrupt */
+	if (!this->complete.done)
+		complete(&this->complete);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * onenand_interrupt_wait - [DEFAULT] wait until the command is done
+ * @param mtd		MTD device structure
+ * @param state		state to select the max. timeout value
+ *
+ * Wait for command done.
+ */
+static int onenand_interrupt_wait(struct mtd_info *mtd, int state)
+{
+	struct onenand_chip *this = mtd->priv;
+
+	/* To prevent soft lockup */
+	touch_softlockup_watchdog();
+
+	wait_for_completion(&this->complete);
+
+	return onenand_wait(mtd, state);
+}
+
+/*
+ * onenand_try_interrupt_wait - [DEFAULT] try interrupt wait
+ * @param mtd		MTD device structure
+ * @param state		state to select the max. timeout value
+ *
+ * Try interrupt based wait (It is used one-time)
+ */
+static int onenand_try_interrupt_wait(struct mtd_info *mtd, int state)
+{
+	struct onenand_chip *this = mtd->priv;
+	unsigned long remain, timeout;
+
+	/* We use interrupt wait first */
+	this->wait = onenand_interrupt_wait;
+
+	/* To prevent soft lockup */
+	touch_softlockup_watchdog();
+
+	timeout = msecs_to_jiffies(100);
+	remain = wait_for_completion_timeout(&this->complete, timeout);
+	if (!remain) {
+		printk(KERN_INFO "OneNAND: There's no interrupt. "
+				"We use the normal wait\n");
+
+		/* Release the irq */
+		free_irq(this->irq, this);
+		
+		this->wait = onenand_wait;
+	}
+
+	return onenand_wait(mtd, state);
+}
+
+/*
+ * onenand_setup_wait - [OneNAND Interface] setup onenand wait method
+ * @param mtd		MTD device structure
+ *
+ * There's two method to wait onenand work
+ * 1. polling - read interrupt status register
+ * 2. interrupt - use the kernel interrupt method
+ */
+static void onenand_setup_wait(struct mtd_info *mtd)
+{
+	struct onenand_chip *this = mtd->priv;
+	int syscfg;
+
+	init_completion(&this->complete);
+
+	if (this->irq <= 0) {
+		this->wait = onenand_wait;
+		return;
+	}
+
+	if (request_irq(this->irq, &onenand_interrupt,
+				IRQF_SHARED, "onenand", this)) {
+		/* If we can't get irq, use the normal wait */
+		this->wait = onenand_wait;
+		return;
+	}
+
+	/* Enable interrupt */
+	syscfg = this->read_word(this->base + ONENAND_REG_SYS_CFG1);
+	syscfg |= ONENAND_SYS_CFG1_IOBE;
+	this->write_word(syscfg, this->base + ONENAND_REG_SYS_CFG1);
+
+	this->wait = onenand_try_interrupt_wait;
+}
+
 /**
  * onenand_bufferram_offset - [DEFAULT] BufferRAM offset
  * @param mtd		MTD data structure
@@ -1129,7 +1235,6 @@ static void onenand_sync(struct mtd_info
 	onenand_release_device(mtd);
 }
 
-
 /**
  * onenand_block_isbad - [MTD Interface] Check whether the block at the given offset is bad
  * @param mtd		MTD device structure
@@ -1846,7 +1951,7 @@ int onenand_scan(struct mtd_info *mtd, i
 	if (!this->command)
 		this->command = onenand_command;
 	if (!this->wait)
-		this->wait = onenand_wait;
+		onenand_setup_wait(mtd);
 
 	if (!this->read_bufferram)
 		this->read_bufferram = onenand_read_bufferram;
diff --git a/include/asm-arm/arch-omap/omap24xx.h b/include/asm-arm/arch-omap/omap24xx.h
index 6e59805..a497dcc 100644
--- a/include/asm-arm/arch-omap/omap24xx.h
+++ b/include/asm-arm/arch-omap/omap24xx.h
@@ -16,6 +16,8 @@ #define VA_IC_BASE		IO_ADDRESS(OMAP24XX_
 #define OMAP24XX_IVA_INTC_BASE	0x40000000
 #define IRQ_SIR_IRQ		0x0040
 
+#define OMAP242X_CONTROL_STATUS	(L4_24XX_BASE + 0x2f8)
+
 #define OMAP24XX_32KSYNCT_BASE	(L4_24XX_BASE + 0x4000)
 #define OMAP24XX_PRCM_BASE	(L4_24XX_BASE + 0x8000)
 #define OMAP24XX_SDRC_BASE	(L3_24XX_BASE + 0x9000)
diff --git a/include/linux/mtd/onenand.h b/include/linux/mtd/onenand.h
index 6f045b5..df963f1 100644
--- a/include/linux/mtd/onenand.h
+++ b/include/linux/mtd/onenand.h
@@ -13,6 +13,7 @@ #ifndef __LINUX_MTD_ONENAND_H
 #define __LINUX_MTD_ONENAND_H
 
 #include <linux/spinlock.h>
+#include <linux/completion.h>
 #include <linux/mtd/onenand_regs.h>
 #include <linux/mtd/bbm.h>
 
@@ -120,6 +121,9 @@ struct onenand_chip {
 	int (*block_markbad)(struct mtd_info *mtd, loff_t ofs);
 	int (*scan_bbt)(struct mtd_info *mtd);
 
+	struct completion	complete;
+	int			irq;
+
 	spinlock_t		chip_lock;
 	wait_queue_head_t	wq;
 	onenand_state_t		state;


More information about the linux-mtd mailing list