[PATCH] Make nand block functions use provided byte/word helpers.

[Jonathan McDowell]

Hi.

I've been writing a NAND driver for the flash on the Amstrad E3. One of
the peculiarities of this device is that the write & read enable lines
are on a latch, rather than strobed by the act of reading/writing from
the data latch. As such I've got custom read_byte/write_byte functions
defined. However the nand_*_buf functions in drivers/mtd/nand/nand_base.c
are all appropriate, except for the fact they call readb/writeb
themselves, instead of using this->read_byte or this->write_byte. The
patch below changes them to use these functions, meaning a driver just
needs to define read_byte and write_byte functions and gains all the
nand_*_buf functions free.

Signed-off-by: Jonathan McDowell <noodles at earth.li>


----------
--- linux-2.6.15/drivers/mtd/nand/nand_base.c.orig	2006-02-28 20:41:54.000000000 +0000
+++ linux-2.6.15/drivers/mtd/nand/nand_base.c	2006-02-28 20:46:44.000000000 +0000
@@ -302,7 +302,7 @@ static void nand_write_buf(struct mtd_in
 	struct nand_chip *this = mtd->priv;
 
 	for (i=0; i<len; i++)
-		writeb(buf[i], this->IO_ADDR_W);
+		this->write_byte(mtd, buf[i]);
 }
 
 /**
@@ -319,7 +319,7 @@ static void nand_read_buf(struct mtd_inf
 	struct nand_chip *this = mtd->priv;
 
 	for (i=0; i<len; i++)
-		buf[i] = readb(this->IO_ADDR_R);
+		buf[i] = this->read_byte(mtd);
 }
 
 /**
@@ -336,7 +336,7 @@ static int nand_verify_buf(struct mtd_in
 	struct nand_chip *this = mtd->priv;
 
 	for (i=0; i<len; i++)
-		if (buf[i] != readb(this->IO_ADDR_R))
+		if (buf[i] != this->read_byte(mtd))
 			return -EFAULT;
 
 	return 0;
@@ -358,7 +358,7 @@ static void nand_write_buf16(struct mtd_
 	len >>= 1;
 
 	for (i=0; i<len; i++)
-		writew(p[i], this->IO_ADDR_W);
+		this->write_word(mtd, p[i]);
 
 }
 
@@ -378,7 +378,7 @@ static void nand_read_buf16(struct mtd_i
 	len >>= 1;
 
 	for (i=0; i<len; i++)
-		p[i] = readw(this->IO_ADDR_R);
+		p[i] = this->read_word(mtd);
 }
 
 /**
@@ -397,7 +397,7 @@ static int nand_verify_buf16(struct mtd_
 	len >>= 1;
 
 	for (i=0; i<len; i++)
-		if (p[i] != readw(this->IO_ADDR_R))
+		if (p[i] != this->read_word(mtd))
 			return -EFAULT;
 
 	return 0;
----------

J.

-- 
 [   There are always at least two ways to program the same thing.    ]
 [ http://www.blackcatnetworks.co.uk/ - IPv6 enabled ADSL/dialup/colo ]