sub-module loading (was: Anyone got drivers/mtd/maps/pm828.c?)

Clemens Koller clemens.koller at anagramm.de
Thu Jun 16 04:47:23 EDT 2005


Hi, Alex...
good to know, that you made good progress. :-)

I just X-post this to linux-mtd so maybe somebody can have a look
at your issue, too.

I also experienced "problems" with sub-module-loading. Or maybe
I just missed something:
I need to load mtdchar and map_ram separately in order to be
able to probe my mminfo.ko module to access/mess some
SRAM in my FPGA on a MPC8540. I didn't care about that yet,
but maybe there are missing dependencies which can be solved
automagically here. Or is the sub-module loading supposed to
work like this (well, manual) as somebody might want to choose
in between i.e. mtdblock and/or mtdchar?

I'm talking about the Kernel 2.6.11.11 mtd subsystem.

Best greets,

Clemens Koller
_______________________________
R&D Imaging Devices
Anagramm GmbH
Rupert-Mayer-Str. 45/1
81379 Muenchen
Germany

http://www.anagramm.de
Phone: +49-89-741518-50
Fax: +49-89-741518-19

Alex Zeffertt wrote:
> Hi Clemens,
> 
> Thanks for your help.  I've done it now (see attached).  The
> partitioning is specific to our application but it is easily modified.
> 
> I noticed a buggette in the mtd code while doing this.  If you build
> everything as a module then the sub-module loading doesn't work
> properly.  For example in gen_probe.c it says
> 
> #ifdef CONFIG_MTD_CFI_INTELEXT
> 	case 0x0001:
> 	case 0x0003:
> 		return cfi_cmdset_0001(map, primary);
> #endif
> 
> where it should really say
> 
> #if defined(CONFIG_MTD_CFI_INTELEXT) ||
>     defined(CONFIG_MTD_CFI_INTELEXT_MODULE)
> 	case 0x0001:
> 	case 0x0003:
> 		return cfi_cmdset_0001(map, primary);
> #endif
> 
> There are several problems like this.  In the end I gave up and just
> built everything except the actual mapping driver as kernel resident.
> 
> Alex
> 
> 
> On Wed, 15 Jun 2005 15:18:37 +0200
> Clemens Koller <clemens.koller at anagramm.de> wrote:
> 
> 
>>Hi, Alex!
>>
>>Hmm, I don't know the PM828 much in detail, but have you
>>tried the "generic" physmap driver which is in the kernel?
>>Just give it the base address and the size, and it should
>>probe the cfi and you are done (well, it was working fine
>>for me on my PM854).
>>Of course, you need to make sure, that your hardware / memory
>>mapping is initialized properly (which happens usually in the
>>boot loader). If it's not, let me know and I can give you
>>some code to mess around with the registers in a kernel module.
>>
>>Best greets,
>>
>>Clemens Koller
>>_______________________________
>>R&D Imaging Devices
>>Anagramm GmbH
>>Rupert-Mayer-Str. 45/1
>>81379 Muenchen
>>Germany
>>
>>http://www.anagramm.de
>>Phone: +49-89-741518-50
>>Fax: +49-89-741518-19
>>
>>
>>Alex Zeffertt wrote:
>>
>>>Hi there,
>>>
>>>I need to get flash partitions working on my PM828 development
>>>board. Has anybody already written a pm828.c?  If so I'd appreciate
>>>a look at it.
>>>
>>>TIA,
>>>
>>>Alex
>>>_______________________________________________
>>>Linuxppc-embedded mailing list
>>>Linuxppc-embedded at ozlabs.org
>>>https://ozlabs.org/mailman/listinfo/linuxppc-embedded
>>>




More information about the linux-mtd mailing list