mtd: nand: denali: remove unused CONFIG option and macros
Linux-MTD Mailing List
linux-mtd at lists.infradead.org
Wed May 10 19:59:09 PDT 2017
Gitweb: http://git.infradead.org/?p=mtd-2.6.git;a=commit;h=357cc408a4009c0d118b684e4865f85694ebc68c
Commit: 357cc408a4009c0d118b684e4865f85694ebc68c
Parent: c120e75e0e7deff88119376298342df139b9b17c
Author: Masahiro Yamada <yamada.masahiro at socionext.com>
AuthorDate: Thu Mar 23 05:07:02 2017 +0900
Committer: Boris Brezillon <boris.brezillon at free-electrons.com>
CommitDate: Fri Mar 24 09:51:28 2017 +0100
mtd: nand: denali: remove unused CONFIG option and macros
All of these macros are not used at all.
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but
defining SCRATCH_REG_ADDR. The config option should go away as well.
I am removing some register macros. They are not used, and do not
exist in recent IP versions.
Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon at free-electrons.com>
---
drivers/mtd/nand/Kconfig | 11 ------
drivers/mtd/nand/denali.c | 5 ---
drivers/mtd/nand/denali.h | 99 -----------------------------------------------
3 files changed, 115 deletions(-)
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index ae7ae77..aa44fb0 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -59,17 +59,6 @@ config MTD_NAND_DENALI_DT
Enable the driver for NAND flash on platforms using a Denali NAND
controller as a DT device.
-config MTD_NAND_DENALI_SCRATCH_REG_ADDR
- hex "Denali NAND size scratch register address"
- default "0xFF108018"
- depends on MTD_NAND_DENALI_PCI
- help
- Some platforms place the NAND chip size in a scratch register
- because (some versions of) the driver aren't able to automatically
- determine the size of certain chips. Set the address of the
- scratch register here to enable this feature. On Intel Moorestown
- boards, the scratch register is at 0xFF108018.
-
config MTD_NAND_GPIO
tristate "GPIO assisted NAND Flash driver"
depends on GPIOLIB || COMPILE_TEST
diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 73b9d4e..f993e13 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -91,11 +91,6 @@ static inline struct denali_nand_info *mtd_to_denali(struct mtd_info *mtd)
#define DENALI_READ 0
#define DENALI_WRITE 0x100
-/* types of device accesses. We can issue commands and get status */
-#define COMMAND_CYCLE 0
-#define ADDR_CYCLE 1
-#define STATUS_CYCLE 2
-
/*
* this is a helper macro that allows us to
* format the bank into the proper bits for the controller
diff --git a/drivers/mtd/nand/denali.h b/drivers/mtd/nand/denali.h
index ea22191..c4f3a68 100644
--- a/drivers/mtd/nand/denali.h
+++ b/drivers/mtd/nand/denali.h
@@ -257,26 +257,6 @@
#define ERR_PAGE_ADDR(__bank) (0x440 + ((__bank) * 0x50))
#define ERR_BLOCK_ADDR(__bank) (0x450 + ((__bank) * 0x50))
-#define DATA_INTR 0x550
-#define DATA_INTR__WRITE_SPACE_AV 0x0001
-#define DATA_INTR__READ_DATA_AV 0x0002
-
-#define DATA_INTR_EN 0x560
-#define DATA_INTR_EN__WRITE_SPACE_AV 0x0001
-#define DATA_INTR_EN__READ_DATA_AV 0x0002
-
-#define GPREG_0 0x570
-#define GPREG_0__VALUE 0xffff
-
-#define GPREG_1 0x580
-#define GPREG_1__VALUE 0xffff
-
-#define GPREG_2 0x590
-#define GPREG_2__VALUE 0xffff
-
-#define GPREG_3 0x5a0
-#define GPREG_3__VALUE 0xffff
-
#define ECC_THRESHOLD 0x600
#define ECC_THRESHOLD__VALUE 0x03ff
@@ -331,69 +311,15 @@
#define CHNL_ACTIVE__CHANNEL2 0x0004
#define CHNL_ACTIVE__CHANNEL3 0x0008
-#define ACTIVE_SRC_ID 0x800
-#define ACTIVE_SRC_ID__VALUE 0x00ff
-
-#define PTN_INTR 0x810
-#define PTN_INTR__CONFIG_ERROR 0x0001
-#define PTN_INTR__ACCESS_ERROR_BANK0 0x0002
-#define PTN_INTR__ACCESS_ERROR_BANK1 0x0004
-#define PTN_INTR__ACCESS_ERROR_BANK2 0x0008
-#define PTN_INTR__ACCESS_ERROR_BANK3 0x0010
-#define PTN_INTR__REG_ACCESS_ERROR 0x0020
-
-#define PTN_INTR_EN 0x820
-#define PTN_INTR_EN__CONFIG_ERROR 0x0001
-#define PTN_INTR_EN__ACCESS_ERROR_BANK0 0x0002
-#define PTN_INTR_EN__ACCESS_ERROR_BANK1 0x0004
-#define PTN_INTR_EN__ACCESS_ERROR_BANK2 0x0008
-#define PTN_INTR_EN__ACCESS_ERROR_BANK3 0x0010
-#define PTN_INTR_EN__REG_ACCESS_ERROR 0x0020
-
-#define PERM_SRC_ID(__bank) (0x830 + ((__bank) * 0x40))
-#define PERM_SRC_ID__SRCID 0x00ff
-#define PERM_SRC_ID__DIRECT_ACCESS_ACTIVE 0x0800
-#define PERM_SRC_ID__WRITE_ACTIVE 0x2000
-#define PERM_SRC_ID__READ_ACTIVE 0x4000
-#define PERM_SRC_ID__PARTITION_VALID 0x8000
-
-#define MIN_BLK_ADDR(__bank) (0x840 + ((__bank) * 0x40))
-#define MIN_BLK_ADDR__VALUE 0xffff
-
-#define MAX_BLK_ADDR(__bank) (0x850 + ((__bank) * 0x40))
-#define MAX_BLK_ADDR__VALUE 0xffff
-
-#define MIN_MAX_BANK(__bank) (0x860 + ((__bank) * 0x40))
-#define MIN_MAX_BANK__MIN_VALUE 0x0003
-#define MIN_MAX_BANK__MAX_VALUE 0x000c
-
-
-/* ffsdefs.h */
-#define CLEAR 0 /*use this to clear a field instead of "fail"*/
-#define SET 1 /*use this to set a field instead of "pass"*/
#define FAIL 1 /*failed flag*/
#define PASS 0 /*success flag*/
-#define ERR -1 /*error flag*/
-
-/* lld.h */
-#define GOOD_BLOCK 0
-#define DEFECTIVE_BLOCK 1
-#define READ_ERROR 2
#define CLK_X 5
#define CLK_MULTI 4
-/* KBV - Updated to LNW scratch register address */
-#define SCRATCH_REG_ADDR CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR
-#define SCRATCH_REG_SIZE 64
-
-#define GLOB_HWCTL_DEFAULT_BLKS 2048
-
#define SUPPORT_15BITECC 1
#define SUPPORT_8BITECC 1
-#define CUSTOM_CONF_PARAMS 0
-
#define ONFI_BLOOM_TIME 1
#define MODE5_WORKAROUND 0
@@ -403,31 +329,6 @@
#define MODE_10 0x08000000
#define MODE_11 0x0C000000
-
-#define DATA_TRANSFER_MODE 0
-#define PROTECTION_PER_BLOCK 1
-#define LOAD_WAIT_COUNT 2
-#define PROGRAM_WAIT_COUNT 3
-#define ERASE_WAIT_COUNT 4
-#define INT_MONITOR_CYCLE_COUNT 5
-#define READ_BUSY_PIN_ENABLED 6
-#define MULTIPLANE_OPERATION_SUPPORT 7
-#define PRE_FETCH_MODE 8
-#define CE_DONT_CARE_SUPPORT 9
-#define COPYBACK_SUPPORT 10
-#define CACHE_WRITE_SUPPORT 11
-#define CACHE_READ_SUPPORT 12
-#define NUM_PAGES_IN_BLOCK 13
-#define ECC_ENABLE_SELECT 14
-#define WRITE_ENABLE_2_READ_ENABLE 15
-#define ADDRESS_2_DATA 16
-#define READ_ENABLE_2_WRITE_ENABLE 17
-#define TWO_ROW_ADDRESS_CYCLES 18
-#define MULTIPLANE_ADDRESS_RESTRICT 19
-#define ACC_CLOCKS 20
-#define READ_WRITE_ENABLE_LOW_COUNT 21
-#define READ_WRITE_ENABLE_HIGH_COUNT 22
-
#define ECC_SECTOR_SIZE 512
struct nand_buf {
More information about the linux-mtd-cvs
mailing list