[PATCH v2 11/21] arm64: dts: apple: t8103-j313: Add speaker/headset jack nodes

[Ajay Kumar Nandam]

On 10/4/2026 11:33 AM, James Calligeros wrote:
> The M1 MacBook Air integrates Apple-specific variants of the TI TAS2770
> and Cirrus CS42L42. Add these nodes and advertise them to the machine
> driver via the sound node.
> 
> Signed-off-by: James Calligeros <jcalligeros99 at gmail.com>
> ---
>   arch/arm64/boot/dts/apple/t8103-j313.dts | 82 +++++++++++++++++++++++++
>   1 file changed, 82 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/apple/t8103-j313.dts b/arch/arm64/boot/dts/apple/t8103-j313.dts
> index f8b2b1637b9d..cdda63ca8b34 100644
> --- a/arch/arm64/boot/dts/apple/t8103-j313.dts
> +++ b/arch/arm64/boot/dts/apple/t8103-j313.dts
> @@ -55,4 +55,86 @@ &typec1 {
>   	label = "USB-C Left-front";
>   };
>   
> +/* Audio codecs */
> +&i2c1 {
> +	status = "okay";
> +
> +	speaker_left: codec at 31 {
> +		compatible = "ti,tas5770l";
> +		reg = <0x31>;
> +		interrupts-extended = <&pinctrl_ap 182 IRQ_TYPE_LEVEL_LOW>;
> +		shutdown-gpios = <&pinctrl_ap 181 GPIO_ACTIVE_HIGH>;
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "Left";
> +		ti,imon-slot-no = <0>;
> +		ti,vmon-slot-no = <2>;
> +	};
> +};
> +
> +&i2c3 {
> +	status = "okay";
> +
> +	speaker_right: codec at 34 {
> +		compatible = "ti,tas5770l";
> +		reg = <0x34>;
> +		interrupts-extended = <&pinctrl_ap 182 IRQ_TYPE_LEVEL_LOW>;
> +		shutdown-gpios = <&pinctrl_ap 181 GPIO_ACTIVE_HIGH>;
> +		#sound-dai-cells = <0>;

Both speaker codec nodes reference the same shutdown GPIO. Is that
intentional for this board?

The TAS2770 driver requests 'shutdown-gpios' per codec instance, and 
GPIO requests are exclusive by default. So I would expect only one codec 
instance to own this line, while the other appears to fall back to the 
register-only path after the GPIO request fails.

If GPIO181 is a shared physical shutdown line for both amps, how is the
power/reset ordering expected to work across probe, suspend, and resume 
when only one of the two codec driver instances controls that line?

Thanks
Ajay Kumar Nandam

> +		sound-name-prefix = "Right";
> +		ti,imon-slot-no = <4>;
> +		ti,vmon-slot-no = <6>;
> +	};
> +
> +	jack_codec: codec at 48 {
> +		compatible = "cirrus,cs42l83";
> +		reg = <0x48>;
> +		interrupts-extended = <&pinctrl_ap 183 IRQ_TYPE_LEVEL_LOW>;
> +		reset-gpios = <&pinctrl_nub 11 GPIO_ACTIVE_HIGH>;
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "Jack";
> +		cirrus,ts-inv = <1>;
> +	};
> +};
> +
> +/ {
> +	sound: sound {
> +		compatible = "apple,j313-macaudio";
> +		model = "MacBook Air J313";
> +
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		dai-link at 0 {
> +			reg = <0>;
> +
> +			dai-tdm-idle-mode-0 = "zero";
> +			dai-tdm-idle-mode-1 = "zero";
> +
> +			link-name = "Speakers";
> +
> +			codec {
> +				sound-dai = <&speaker_left>, <&speaker_right>;
> +			};
> +
> +			cpu {
> +				sound-dai = <&mca 0>, <&mca 1>;
> +			};
> +		};
> +
> +		dai-link at 1 {
> +			reg = <1>;
> +
> +			link-name = "Headphone Jack";
> +
> +			codec {
> +				sound-dai = <&jack_codec>;
> +			};
> +
> +			cpu {
> +				sound-dai = <&mca 2>;
> +			};
> +		};
> +	};
> +};
> +
>   #include "hwmon-laptop.dtsi"
>