[PATCH 5/5] PCI: mediatek-gen3: Keep PCIe power and clocks if suspend-to-idle
Bjorn Helgaas
helgaas at kernel.org
Fri Jan 3 11:13:31 PST 2025
On Fri, Jan 03, 2025 at 02:00:15PM +0800, Jianjun Wang wrote:
> If the target system sleep state is suspend-to-idle, the bridge is
> supposed to stay in D0, and the framework will not help to restore its
> configuration space, so keep its power and clocks during suspend.
>
> It's recommended to enable L1ss support, so the link can be changed to
> L1.2 state during suspend.
>
> Signed-off-by: Jianjun Wang <jianjun.wang at mediatek.com>
> ---
> drivers/pci/controller/pcie-mediatek-gen3.c | 18 ++++++++++++++++++
> 1 file changed, 18 insertions(+)
>
> diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
> index 48f83c2d91f7..11da68910502 100644
> --- a/drivers/pci/controller/pcie-mediatek-gen3.c
> +++ b/drivers/pci/controller/pcie-mediatek-gen3.c
> @@ -1291,6 +1291,19 @@ static int mtk_pcie_suspend_noirq(struct device *dev)
> int err;
> u32 val;
>
> + /*
> + * If the target system sleep state is suspend-to-idle, the bridge is supposed to stay in
> + * D0, and the framework will not help to restore its configuration space, so keep it's
> + * power and clocks during suspend.
s/it's/its/
Where does the requirement for the bridge to stay in D0 come from? Is
that part of the Linux power management framework? Or is this
something specific to this SoC?
I guess "framework" refers to Linux power management, so maybe that
assumes nothing needs to be restored when resuming from
suspend-to-idle?
> + * It's recommended to enable L1ss support, so the link can be changed to L1.2 state during
> + * suspend.
Wrap to fit in 80 columns like the rest of the file.
s/L1ss/L1SS/
Who recommends enabling L1SS support? I suppose enabling L1SS means
setting CONFIG_PCIEASPM=y?
What causes the transition to L1.2? Is this done by firmware or
something else outside of Linux?
> + if (pm_suspend_default_s2idle()) {
> + dev_info(dev, "System enter s2idle state, keep PCIe power and clocks\n");
1) I'm a bit dubious about this since there are only two callers of
pm_suspend_default_s2idle() in the rest of the kernel. What's unique
about this device that requires this? Is this an indication that
we're setting mtk_pcie_pm_ops incorrectly, i.e., are we using
mtk_pcie_suspend_noirq() for a callback that is *never* supposed to
power down the device?
2) The message seems like possible overkill, maybe could be dev_dbg()?
I'm not sure the user needs this information at every suspend/resume
transition.
> + return 0;
> + }
> +
> /* Trigger link to L2 state */
> err = mtk_pcie_turn_off_link(pcie);
> if (err) {
> @@ -1316,6 +1329,11 @@ static int mtk_pcie_resume_noirq(struct device *dev)
> struct mtk_gen3_pcie *pcie = dev_get_drvdata(dev);
> int err;
>
> + if (pm_suspend_default_s2idle()) {
> + dev_info(dev, "System enter s2idle state, no need to reinitialization\n");
> + return 0;
> + }
> +
> err = pcie->soc->power_up(pcie);
> if (err)
> return err;
> --
> 2.46.0
>
More information about the Linux-mediatek
mailing list