[PATCH v3 1/2] arm64: dts: mediatek: mt8395-genio-1200-evk: add support for TCPC port

[AngeloGioacchino Del Regno]

Il 23/10/24 10:09, Macpaul Lin ha scritto:
> From: Fabien Parent <fparent at baylibre.com>
> 
> Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding
> configuration for TCPC Port, USB-C connector, and related settings.
> 
> Configure dual role switch capability, set up PD (Power Delivery) profiles,
> and establish endpoints for SSUSB (SuperSpeed USB).
> 
> Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode
> to "otg" for OTG (On-The-Go) mode operation.
> 
> Signed-off-by: Fabien Parent <fparent at baylibre.com>
> Signed-off-by: Yow-Shin Liou <yow-shin.liou at mediatek.com>
> Signed-off-by: Simon Sun <simon.sun at yunjingtech.com>
> Signed-off-by: Macpaul Lin <macpaul.lin at mediatek.com>
> ---
>   .../dts/mediatek/mt8395-genio-1200-evk.dts    | 54 +++++++++++++++++++
>   1 file changed, 54 insertions(+)
> 
> Changes for v2:
>   - Drop the no need '1/2' DT Schema update patch in the 1st version.
>   - Fix intent for 'ports' node, it should under the 'connector' node.
>   - Correct the index for 'port at 0' and 'port at 1' node.
> 
> Changes for v3:
>   - Correct the order between new added nodes.
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
> index 5f16fb820580..83d520226302 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
> @@ -335,6 +335,43 @@ mt6360_ldo7: ldo7 {
>   				regulator-always-on;
>   			};
>   		};
> +
> +		tcpc {
> +			compatible = "mediatek,mt6360-tcpc";
> +			interrupts-extended = <&pio 17 IRQ_TYPE_LEVEL_LOW>;
> +			interrupt-names = "PD_IRQB";
> +
> +			connector {
> +				compatible = "usb-c-connector";
> +				label = "USB-C";
> +				data-role = "dual";

op-sink-microwatt goes here

> +				power-role = "dual";
> +				try-power-role = "sink";
> +				source-pdos = <PDO_FIXED(5000, 1000, \
> +					       PDO_FIXED_DUAL_ROLE | \
> +					       PDO_FIXED_DATA_SWAP)>;

Please fix the indentation (and also you don't need the escaping)

				source-pdos = <PDO_FIXED(5000, 1000,
							 PDO_FIXED_DUAL_ROLE |
							 PDO_FIXED_DATA_SWAP)>;

> +				sink-pdos = <PDO_FIXED(5000, 2000, \
> +					     PDO_FIXED_DUAL_ROLE | \
> +					     PDO_FIXED_DATA_SWAP)>;
> +				op-sink-microwatt = <10000000>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;

Just to make sure that this is ok: are you sure that this port supports
SuperSpeed (physical connector too) and that it's not limited to HighSpeed?

I have seen Rob's comment stating that ssusb_ep goes to port at 1, but I think
that his comment came after reading "ss" in "ssusb": while the controller
does surely support SS, if the port does not, this should still go to port at 0.

P.S.: I didn't check the schematics - just please make sure it's correct, and
       that this actually works.

> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +						mt6360_ssusb_ep: endpoint {
> +							remote-endpoint = <&ssusb_ep>;
> +						};
> +					};
> +				};
> +			};
> +		};
>   	};
>   };
>   
> @@ -770,6 +807,13 @@ pins-reset {
>   		};
>   	};
>   
> +	u3_p0_vbus: u3-p0-vbus-default-pins {
> +		pins-cmd-dat {

That's not a command nor data pin.

pins-vbus {

> +			pinmux = <PINMUX_GPIO63__FUNC_VBUSVALID>;
> +			input-enable;
> +		};
> +	};
> +
>   	uart0_pins: uart0-pins {
>   		pins {
>   			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
> @@ -900,8 +944,18 @@ &ufsphy {
>   };
>   
>   &ssusb0 {
> +	dr_mode = "otg";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&u3_p0_vbus>;

Is this port usb host by default? If it is:

	role-switch-default-mode = "host";

Cheers,
Angelo

> +	usb-role-switch;
>   	vusb33-supply = <&mt6359_vusb_ldo_reg>;
>   	status = "okay";
> +
> +	port {
> +		ssusb_ep: endpoint {
> +			remote-endpoint = <&mt6360_ssusb_ep>;
> +		};
> +	};
>   };
>   
>   &ssusb2 {