[PATCH 2/2] arm64: dts: mediatek: mt8395-genio-1200-evk: add support for TCPC port

[Macpaul Lin]

On 10/16/24 04:56, Rob Herring wrote:
> 	
> 
> External email : Please do not click links or open attachments until you 
> have verified the sender or the content.
> 
> On Tue, Oct 15, 2024 at 06:33:37PM +0800, Macpaul Lin wrote:
>> From: Fabien Parent <fparent at baylibre.com>
>> 
>> Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding
>> configuration for TCPC Port, USB-C connector, and related settings.
>> 
>> Configure dual role switch capability, set up PD (Power Delivery) profiles,
>> and establish endpoints for SSUSB (SuperSpeed USB).
>> 
>> Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode
>> to "otg" for OTG (On-The-Go) mode operation.
>> 
>> Signed-off-by: Fabien Parent <fparent at baylibre.com>
>> Signed-off-by: Simon Sun <simon.sun at yunjingtech.com>
>> Signed-off-by: Macpaul Lin <macpaul.lin at mediatek.com>
>> ---
>>  .../dts/mediatek/mt8395-genio-1200-evk.dts    | 51 +++++++++++++++++++
>>  1 file changed, 51 insertions(+)
>> 
>> diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
>> index 5f16fb820580..b91a46f4a702 100644
>> --- a/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
>> +++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dts
>> @@ -249,6 +249,39 @@ mt6360: pmic at 34 {
>>  #interrupt-cells = <1>;
>>  pinctrl-0 = <&mt6360_pins>;
>>  
>> +tcpc {
>> +compatible = "mediatek,mt6360-tcpc";
>> +interrupts-extended = <&pio 17 IRQ_TYPE_LEVEL_LOW>;
>> +interrupt-names = "PD_IRQB";
>> +
>> +connector {
>> +compatible = "usb-c-connector";
>> +label = "USB-C";
>> +data-role = "dual";
>> +power-role = "dual";
>> +try-power-role = "sink";
>> +source-pdos = <PDO_FIXED(5000, 1000, \
>> +       PDO_FIXED_DUAL_ROLE | \
>> +       PDO_FIXED_DATA_SWAP)>;
>> +sink-pdos = <PDO_FIXED(5000, 2000, \
>> +     PDO_FIXED_DUAL_ROLE | \
>> +     PDO_FIXED_DATA_SWAP)>;
>> +op-sink-microwatt = <10000000>;
>> +};
>> +
>> +ports {
>> +#address-cells = <1>;
>> +#size-cells = <0>;
>> +
>> +port at 0 {
>> +reg = <0>;
>> +mt6360_ssusb_ep: endpoint {
>> +remote-endpoint = <&ssusb_ep>;
> 
> No, this is wrong. This should go to 'port at 1' in the connector node.
> That is the SS connection.
> 
> Rob

This wrong index and wrong intent for the whole 'ports' node will be
fixed in patch v2.

Thanks for the review.
Macpaul Lin