[PATCH v12 1/3] dt-bindings: display: mediatek: Add OF graph support for board path
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Thu Oct 17 03:18:57 PDT 2024
Il 16/10/24 18:09, Rob Herring ha scritto:
> On Wed, Oct 16, 2024 at 10:26 AM AngeloGioacchino Del Regno
> <angelogioacchino.delregno at collabora.com> wrote:
>>
>> Il 16/10/24 16:00, Rob Herring ha scritto:
>>> On Wed, Oct 16, 2024 at 4:23 AM AngeloGioacchino Del Regno
>>> <angelogioacchino.delregno at collabora.com> wrote:
>>>>
>>>> Il 15/10/24 15:48, Rob Herring ha scritto:
>>>>> On Tue, Oct 15, 2024 at 10:32:22AM +0200, AngeloGioacchino Del Regno wrote:
>>>>>> Il 14/10/24 19:36, Rob Herring ha scritto:
>>>>>>> On Mon, Oct 14, 2024 at 3:51 AM AngeloGioacchino Del Regno
>>>>>>> <angelogioacchino.delregno at collabora.com> wrote:
>>>>>>>>
>>>>>>>> The display IPs in MediaTek SoCs support being interconnected with
>>>>>>>> different instances of DDP IPs (for example, merge0 or merge1) and/or
>>>>>>>> with different DDP IPs (for example, rdma can be connected with either
>>>>>>>> color, dpi, dsi, merge, etc), forming a full Display Data Path that
>>>>>>>> ends with an actual display.
>>>>>>>>
>>>>>>>> The final display pipeline is effectively board specific, as it does
>>>>>>>> depend on the display that is attached to it, and eventually on the
>>>>>>>> sensors supported by the board (for example, Adaptive Ambient Light
>>>>>>>> would need an Ambient Light Sensor, otherwise it's pointless!), other
>>>>>>>> than the output type.
>>>>>>>>
>>>>>>>> Add support for OF graphs to most of the MediaTek DDP (display) bindings
>>>>>>>> to add flexibility to build custom hardware paths, hence enabling board
>>>>>>>> specific configuration of the display pipeline and allowing to finally
>>>>>>>> migrate away from using hardcoded paths.
>>>>>>>>
>>>>>>>> Reviewed-by: Rob Herring (Arm) <robh at kernel.org>
>>>>>>>> Reviewed-by: Alexandre Mergnat <amergnat at baylibre.com>
>>>>>>>> Tested-by: Alexandre Mergnat <amergnat at baylibre.com>
>>>>>>>> Reviewed-by: CK Hu <ck.hu at mediatek.com>
>>>>>>>> Tested-by: Michael Walle <mwalle at kernel.org> # on kontron-sbc-i1200
>>>>>>>> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
>>>>>>>> ---
>>>>>>>> .../display/mediatek/mediatek,aal.yaml | 40 +++++++++++++++++++
>>>>>>>> .../display/mediatek/mediatek,ccorr.yaml | 21 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,color.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,dither.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,dpi.yaml | 25 +++++++++++-
>>>>>>>> .../display/mediatek/mediatek,dsc.yaml | 24 +++++++++++
>>>>>>>> .../display/mediatek/mediatek,dsi.yaml | 27 ++++++++++++-
>>>>>>>> .../display/mediatek/mediatek,ethdr.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,gamma.yaml | 19 +++++++++
>>>>>>>> .../display/mediatek/mediatek,merge.yaml | 23 +++++++++++
>>>>>>>> .../display/mediatek/mediatek,od.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,ovl-2l.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,ovl.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,postmask.yaml | 21 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,rdma.yaml | 22 ++++++++++
>>>>>>>> .../display/mediatek/mediatek,ufoe.yaml | 21 ++++++++++
>>>>>>>> 16 files changed, 372 insertions(+), 3 deletions(-)
>>>>>>>>
>>>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
>>>>>>>> index cf24434854ff..47ddba5c41af 100644
>>>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
>>>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
>>>>>>>> @@ -62,6 +62,27 @@ properties:
>>>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>>>> maxItems: 1
>>>>>>>>
>>>>>>>> + ports:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>>>> + description:
>>>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>>>> +
>>>>>>>> + properties:
>>>>>>>> + port at 0:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description: AAL input port
>>>>>>>> +
>>>>>>>> + port at 1:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description:
>>>>>>>> + AAL output to the next component's input, for example could be one
>>>>>>>> + of many gamma, overdrive or other blocks.
>>>>>>>> +
>>>>>>>> + required:
>>>>>>>> + - port at 0
>>>>>>>> + - port at 1
>>>>>>>> +
>>>>>>>> required:
>>>>>>>> - compatible
>>>>>>>> - reg
>>>>>>>> @@ -89,5 +110,24 @@ examples:
>>>>>>>> power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
>>>>>>>> clocks = <&mmsys CLK_MM_DISP_AAL>;
>>>>>>>> mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x5000 0x1000>;
>>>>>>>> +
>>>>>>>> + ports {
>>>>>>>> + #address-cells = <1>;
>>>>>>>> + #size-cells = <0>;
>>>>>>>> +
>>>>>>>> + port at 0 {
>>>>>>>> + reg = <0>;
>>>>>>>> + aal0_in: endpoint {
>>>>>>>> + remote-endpoint = <&ccorr0_out>;
>>>>>>>> + };
>>>>>>>> + };
>>>>>>>> +
>>>>>>>> + port at 1 {
>>>>>>>> + reg = <1>;
>>>>>>>> + aal0_out: endpoint {
>>>>>>>> + remote-endpoint = <&gamma0_in>;
>>>>>>>> + };
>>>>>>>> + };
>>>>>>>> + };
>>>>>>>> };
>>>>>>>> };
>>>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml
>>>>>>>> index 9f8366763831..fca8e7bb0cbc 100644
>>>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml
>>>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml
>>>>>>>> @@ -57,6 +57,27 @@ properties:
>>>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>>>> maxItems: 1
>>>>>>>>
>>>>>>>> + ports:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>>>> + description:
>>>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>>>> +
>>>>>>>> + properties:
>>>>>>>> + port at 0:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description: CCORR input port
>>>>>>>> +
>>>>>>>> + port at 1:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description:
>>>>>>>> + CCORR output to the input of the next desired component in the
>>>>>>>> + display pipeline, usually only one of the available AAL blocks.
>>>>>>>> +
>>>>>>>> + required:
>>>>>>>> + - port at 0
>>>>>>>> + - port at 1
>>>>>>>> +
>>>>>>>> required:
>>>>>>>> - compatible
>>>>>>>> - reg
>>>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
>>>>>>>> index 7df786bbad20..6160439ce4d7 100644
>>>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
>>>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
>>>>>>>> @@ -65,6 +65,28 @@ properties:
>>>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>>>> maxItems: 1
>>>>>>>>
>>>>>>>> + ports:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>>>> + description:
>>>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>>>> +
>>>>>>>> + properties:
>>>>>>>> + port at 0:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description: COLOR input port
>>>>>>>> +
>>>>>>>> + port at 1:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description:
>>>>>>>> + COLOR output to the input of the next desired component in the
>>>>>>>> + display pipeline, for example one of the available CCORR or AAL
>>>>>>>> + blocks.
>>>>>>>> +
>>>>>>>> + required:
>>>>>>>> + - port at 0
>>>>>>>> + - port at 1
>>>>>>>> +
>>>>>>>> required:
>>>>>>>> - compatible
>>>>>>>> - reg
>>>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml
>>>>>>>> index 6fceb1f95d2a..abaf27916d13 100644
>>>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml
>>>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml
>>>>>>>> @@ -56,6 +56,28 @@ properties:
>>>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>>>> maxItems: 1
>>>>>>>>
>>>>>>>> + ports:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>>>> + description:
>>>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>>>> +
>>>>>>>> + properties:
>>>>>>>> + port at 0:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description: DITHER input, usually from a POSTMASK or GAMMA block.
>>>>>>>> +
>>>>>>>> + port at 1:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description:
>>>>>>>> + DITHER output to the input of the next desired component in the
>>>>>>>> + display pipeline, for example one of the available DSC compressors,
>>>>>>>> + DP_INTF, DSI, LVDS or others.
>>>>>>>> +
>>>>>>>> + required:
>>>>>>>> + - port at 0
>>>>>>>> + - port at 1
>>>>>>>> +
>>>>>>>> required:
>>>>>>>> - compatible
>>>>>>>> - reg
>>>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>>>>>>>> index 3a82aec9021c..b567e3d58aa1 100644
>>>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>>>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>>>>>>>> @@ -71,13 +71,34 @@ properties:
>>>>>>>> Output port node. This port should be connected to the input port of an
>>>>>>>> attached HDMI, LVDS or DisplayPort encoder chip.
>>>>>>>>
>>>>>>>> + ports:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>>>> +
>>>>>>>> + properties:
>>>>>>>> + port at 0:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description: DPI input port
>>>>>>>> +
>>>>>>>> + port at 1:
>>>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>>>> + description: DPI output to an HDMI, LVDS or DisplayPort encoder input
>>>>>>>
>>>>>>> This is wrong. The existing 'port' is the output. 'port' and 'port at 0'
>>>>>>> are treated as the same thing. Since you are adding an input port, the
>>>>>>> new port has to be 'port at 1' (or any number but 0).
>>>>>>>
>>>>>>> I haven't looked at the driver code, but it should request port 0 and
>>>>>>> always get the output port. And requesting port 1 will return an error
>>>>>>> or the input port.
>>>>>>
>>>>>> Hello Rob,
>>>>>>
>>>>>> I want to remind you that in v2 of this series you said that it'd be wrong for
>>>>>> port at 0 to be an output, I replied that you misread that as I had modeled it indeed
>>>>>> as an input, and then you gave me your Reviewed-by tag.
>>>>>
>>>>> I have not misread it. Then I guess I forgot about it and missed it the
>>>>> next time on v3.
>>>>>
>>>>
>>>> Okay, that was some misunderstanding then - it's fine, no problem.
>>>>
>>>>>> Anyway - I get your concern about the previous behavior of `port`, but I chose to
>>>>>> model this that way purely for consistency.
>>>>>>
>>>>>> First of all - the driver(s) will check if we're feeding a full graph, as it will
>>>>>> indeed first check if port at 1 is present: if it is, then it follows this scheme with
>>>>>> port at 0 as INPUT and port at 1 as OUTPUT.
>>>>>> If the component in port at 0 is an OUTPUT, the bridge attach will fail.
>>>>>>
>>>>>> Getting to bindings themselves, then... it would be a mistake to model port at 0 as an
>>>>>> output and port at 1 as an input, because that would be not only inconsistent with the
>>>>>> DRM Bridge bindings, but would be highly confusing when reading the devicetree.
>>>>>
>>>>> Somewhat confusing, yes. Highly, no. Put a comment in the DT.
>>>>>
>>>>
>>>> "Somewhat or highly" boils down to personal opinion, so I still go for "highly"
>>>> but won't argue about that as wouldn't be productive and would bring us nowhere
>>>> anyway, so, whatever :-)
>>>>
>>>> Putting a comment in DT is an option, yes, but that comment would need to be put
>>>> on all of the MediaTek SoC device trees - current and future - and IMO would scream
>>>> "inconsistency warning" (in different words, of course) all over, which honestly
>>>> doesn't really look clean... at least to my eyes...
>>>
>>> What I find more confusing is my updated DT doesn't work with my
>>> existing kernel...
>>>
>>>>>> Please note that the bridge bindings are always declaring port at 0 as an INPUT and
>>>>>> other ports as OUTPUT(s).
>>>>>
>>>>> There is no guarantee on that. Port numbering is local to the bridge and
>>>>> opaque to anything outside that bridge. That is why you have to document
>>>>> what each port represents.
>>>>>
>>>>
>>>> I know and I agree that there's no guarantee on the numbering. I can see that in
>>>> other non-drm-bridge bindings, and that's fine.
>>>>
>>>>> Would we have followed that convention if all the ports were defined
>>>>> from the start? Certainly. But that didn't happen and you are stuck with
>>>>> the existing binding and ABI.
>>>>>
>>>>
>>>> I thought about adding a new compatible for the new port scheme, but that looked
>>>> even worse to me as, after doing that (yeah, I actually went for it in the first
>>>> version that I have never sent upstream) during my own proof-read I started
>>>> screaming "HACK! HACK! NOOO!" all over, and rewritten the entire thing.
>>>>
>>>>>> As an example, you can check display/bridge/analogix,anx7625.yaml or
>>>>>> display/bridge/samsung,mipi-dsim.yaml (and others) for bridges, otherwise
>>>>>> display/st,stm32mp25-lvds.yaml or display/allwinner,sun4i-a10-display-frontend.yaml
>>>>>> (and others) for display controllers, which do all conform to this logic, where
>>>>>> the input is always @0, and the output is @1.
>>>>>>
>>>>>> Of course, doing this required me to do extra changes to the MTK DRM drivers to
>>>>>> actually be retro-compatible with the old devicetrees as I explained before.
>>>>>
>>>>> You can't fix existing software...
>>>>>
>>>>
>>>> That's true, but I don't see that as an "excuse" (grant me this term please) to
>>>> "carelessly" keep it in a suboptimal state.
>>>>
>>>> This driver has been growing almost uncontrollably with (wrong, anyway!)
>>>> board-specific component vectors - and writing a new one would just add up
>>>> more code duplication to the mix and/or worsen the maintainability of older
>>>> MediaTek SoCs (as the "old" driver will get forgotten and never updated anymore).
>>>>
>>>>> If you want to break the ABI, then that's ultimately up to you and
>>>>> Mediatek maintainers to decide0. This case is easy to avoid, why would
>>>>> you knowingly break the ABI here.
>>>>
>>>> Because if we don't do this, we condemn (forever) this driver, or part of it
>>>> to have an inverted port scheme compared to either:
>>>> A. The other drm/mediatek components; or
>>>> B. The other bridge drivers (of which, some are used with MTK as well)
>>>>
>>>> ...and we also condemn (forever, again) all MediaTek device trees to scream
>>>> "port inconsistency warning: A for drm/mediatek components, B for every other
>>>> thing", which would scream "drm/mediatek is somewhat broken", which can be
>>>> avoided.
>>>
>>> Sure. The cost is just an ABI break to do that.
>>>
>>>>> OTOH, this seems like a big enough
>>>>> change I would imagine it is a matter of time before supporting a
>>>>> missing OF graph for the components will be a problem.
>>>>>
>>>>
>>>> Sorry I didn't understand this part, can you please-please-please reword?
>>>
>>> I think keeping the kernel working with the old and new binding will
>>> be a challenge. Partly because testing with the old binding won't
>>> happen, but also if the binding and drivers continue to evolve. So
>>> while maintaining old ABI might be possible with this change, it will
>>> continue to be an issue with each change.
>>
>> That's... exactly my point, so I am happy that we agree on that.
>>
>>> BTW, did you actually test
>>> backwards compatibility with this? I can see you fallback to the old
>>> binding, but there's a lot of other changes in there I can't really
>>> tell by looking at it.
>>
>>
>> Short answer: Yes, largely
>>
>> Long answer:
>>
>> Yes, with this series applied, I have tested both *old* and *new* devicetrees on
>> 7 boards with 4 different SoCs and different display pipelines (hence, graphs):
>> one smartphone (MT6795), a "bunch of" Chromebooks (MT8173, MT8186, MT8195), and
>> a SBC (MT8195).
>>
>> Of course those had DSI or eDP displays, with or without DisplayPort external
>> display support.
>>
>>>
>>> What I haven't heard from you is "yes, we need to maintain the ABI" or
>>> "no, we can break it". Decide that, then the path here is simple.
>>
>> No, we have to break it.
>
> Okay, then my reviewed-by stands. But please make it clear in the
> binding and dts commit msgs that it is an ABI break.
>
Thanks for that.
I'll send a v13 that adds a snippet of text in this commit's description stating
that it breaks the ABI, and I will keep your R-b tag.
Cheers,
Angelo
More information about the Linux-mediatek
mailing list