[PATCH v12 1/3] dt-bindings: display: mediatek: Add OF graph support for board path
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Wed Oct 16 08:26:29 PDT 2024
Il 16/10/24 16:00, Rob Herring ha scritto:
> On Wed, Oct 16, 2024 at 4:23 AM AngeloGioacchino Del Regno
> <angelogioacchino.delregno at collabora.com> wrote:
>>
>> Il 15/10/24 15:48, Rob Herring ha scritto:
>>> On Tue, Oct 15, 2024 at 10:32:22AM +0200, AngeloGioacchino Del Regno wrote:
>>>> Il 14/10/24 19:36, Rob Herring ha scritto:
>>>>> On Mon, Oct 14, 2024 at 3:51 AM AngeloGioacchino Del Regno
>>>>> <angelogioacchino.delregno at collabora.com> wrote:
>>>>>>
>>>>>> The display IPs in MediaTek SoCs support being interconnected with
>>>>>> different instances of DDP IPs (for example, merge0 or merge1) and/or
>>>>>> with different DDP IPs (for example, rdma can be connected with either
>>>>>> color, dpi, dsi, merge, etc), forming a full Display Data Path that
>>>>>> ends with an actual display.
>>>>>>
>>>>>> The final display pipeline is effectively board specific, as it does
>>>>>> depend on the display that is attached to it, and eventually on the
>>>>>> sensors supported by the board (for example, Adaptive Ambient Light
>>>>>> would need an Ambient Light Sensor, otherwise it's pointless!), other
>>>>>> than the output type.
>>>>>>
>>>>>> Add support for OF graphs to most of the MediaTek DDP (display) bindings
>>>>>> to add flexibility to build custom hardware paths, hence enabling board
>>>>>> specific configuration of the display pipeline and allowing to finally
>>>>>> migrate away from using hardcoded paths.
>>>>>>
>>>>>> Reviewed-by: Rob Herring (Arm) <robh at kernel.org>
>>>>>> Reviewed-by: Alexandre Mergnat <amergnat at baylibre.com>
>>>>>> Tested-by: Alexandre Mergnat <amergnat at baylibre.com>
>>>>>> Reviewed-by: CK Hu <ck.hu at mediatek.com>
>>>>>> Tested-by: Michael Walle <mwalle at kernel.org> # on kontron-sbc-i1200
>>>>>> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
>>>>>> ---
>>>>>> .../display/mediatek/mediatek,aal.yaml | 40 +++++++++++++++++++
>>>>>> .../display/mediatek/mediatek,ccorr.yaml | 21 ++++++++++
>>>>>> .../display/mediatek/mediatek,color.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,dither.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,dpi.yaml | 25 +++++++++++-
>>>>>> .../display/mediatek/mediatek,dsc.yaml | 24 +++++++++++
>>>>>> .../display/mediatek/mediatek,dsi.yaml | 27 ++++++++++++-
>>>>>> .../display/mediatek/mediatek,ethdr.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,gamma.yaml | 19 +++++++++
>>>>>> .../display/mediatek/mediatek,merge.yaml | 23 +++++++++++
>>>>>> .../display/mediatek/mediatek,od.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,ovl-2l.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,ovl.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,postmask.yaml | 21 ++++++++++
>>>>>> .../display/mediatek/mediatek,rdma.yaml | 22 ++++++++++
>>>>>> .../display/mediatek/mediatek,ufoe.yaml | 21 ++++++++++
>>>>>> 16 files changed, 372 insertions(+), 3 deletions(-)
>>>>>>
>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
>>>>>> index cf24434854ff..47ddba5c41af 100644
>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,aal.yaml
>>>>>> @@ -62,6 +62,27 @@ properties:
>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>> maxItems: 1
>>>>>>
>>>>>> + ports:
>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>> + description:
>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>> +
>>>>>> + properties:
>>>>>> + port at 0:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description: AAL input port
>>>>>> +
>>>>>> + port at 1:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description:
>>>>>> + AAL output to the next component's input, for example could be one
>>>>>> + of many gamma, overdrive or other blocks.
>>>>>> +
>>>>>> + required:
>>>>>> + - port at 0
>>>>>> + - port at 1
>>>>>> +
>>>>>> required:
>>>>>> - compatible
>>>>>> - reg
>>>>>> @@ -89,5 +110,24 @@ examples:
>>>>>> power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
>>>>>> clocks = <&mmsys CLK_MM_DISP_AAL>;
>>>>>> mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x5000 0x1000>;
>>>>>> +
>>>>>> + ports {
>>>>>> + #address-cells = <1>;
>>>>>> + #size-cells = <0>;
>>>>>> +
>>>>>> + port at 0 {
>>>>>> + reg = <0>;
>>>>>> + aal0_in: endpoint {
>>>>>> + remote-endpoint = <&ccorr0_out>;
>>>>>> + };
>>>>>> + };
>>>>>> +
>>>>>> + port at 1 {
>>>>>> + reg = <1>;
>>>>>> + aal0_out: endpoint {
>>>>>> + remote-endpoint = <&gamma0_in>;
>>>>>> + };
>>>>>> + };
>>>>>> + };
>>>>>> };
>>>>>> };
>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml
>>>>>> index 9f8366763831..fca8e7bb0cbc 100644
>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,ccorr.yaml
>>>>>> @@ -57,6 +57,27 @@ properties:
>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>> maxItems: 1
>>>>>>
>>>>>> + ports:
>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>> + description:
>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>> +
>>>>>> + properties:
>>>>>> + port at 0:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description: CCORR input port
>>>>>> +
>>>>>> + port at 1:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description:
>>>>>> + CCORR output to the input of the next desired component in the
>>>>>> + display pipeline, usually only one of the available AAL blocks.
>>>>>> +
>>>>>> + required:
>>>>>> + - port at 0
>>>>>> + - port at 1
>>>>>> +
>>>>>> required:
>>>>>> - compatible
>>>>>> - reg
>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
>>>>>> index 7df786bbad20..6160439ce4d7 100644
>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,color.yaml
>>>>>> @@ -65,6 +65,28 @@ properties:
>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>> maxItems: 1
>>>>>>
>>>>>> + ports:
>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>> + description:
>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>> +
>>>>>> + properties:
>>>>>> + port at 0:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description: COLOR input port
>>>>>> +
>>>>>> + port at 1:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description:
>>>>>> + COLOR output to the input of the next desired component in the
>>>>>> + display pipeline, for example one of the available CCORR or AAL
>>>>>> + blocks.
>>>>>> +
>>>>>> + required:
>>>>>> + - port at 0
>>>>>> + - port at 1
>>>>>> +
>>>>>> required:
>>>>>> - compatible
>>>>>> - reg
>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml
>>>>>> index 6fceb1f95d2a..abaf27916d13 100644
>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dither.yaml
>>>>>> @@ -56,6 +56,28 @@ properties:
>>>>>> $ref: /schemas/types.yaml#/definitions/phandle-array
>>>>>> maxItems: 1
>>>>>>
>>>>>> + ports:
>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>> + description:
>>>>>> + Input and output ports can have multiple endpoints, each of those
>>>>>> + connects to either the primary, secondary, etc, display pipeline.
>>>>>> +
>>>>>> + properties:
>>>>>> + port at 0:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description: DITHER input, usually from a POSTMASK or GAMMA block.
>>>>>> +
>>>>>> + port at 1:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description:
>>>>>> + DITHER output to the input of the next desired component in the
>>>>>> + display pipeline, for example one of the available DSC compressors,
>>>>>> + DP_INTF, DSI, LVDS or others.
>>>>>> +
>>>>>> + required:
>>>>>> + - port at 0
>>>>>> + - port at 1
>>>>>> +
>>>>>> required:
>>>>>> - compatible
>>>>>> - reg
>>>>>> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>>>>>> index 3a82aec9021c..b567e3d58aa1 100644
>>>>>> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>>>>>> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.yaml
>>>>>> @@ -71,13 +71,34 @@ properties:
>>>>>> Output port node. This port should be connected to the input port of an
>>>>>> attached HDMI, LVDS or DisplayPort encoder chip.
>>>>>>
>>>>>> + ports:
>>>>>> + $ref: /schemas/graph.yaml#/properties/ports
>>>>>> +
>>>>>> + properties:
>>>>>> + port at 0:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description: DPI input port
>>>>>> +
>>>>>> + port at 1:
>>>>>> + $ref: /schemas/graph.yaml#/properties/port
>>>>>> + description: DPI output to an HDMI, LVDS or DisplayPort encoder input
>>>>>
>>>>> This is wrong. The existing 'port' is the output. 'port' and 'port at 0'
>>>>> are treated as the same thing. Since you are adding an input port, the
>>>>> new port has to be 'port at 1' (or any number but 0).
>>>>>
>>>>> I haven't looked at the driver code, but it should request port 0 and
>>>>> always get the output port. And requesting port 1 will return an error
>>>>> or the input port.
>>>>
>>>> Hello Rob,
>>>>
>>>> I want to remind you that in v2 of this series you said that it'd be wrong for
>>>> port at 0 to be an output, I replied that you misread that as I had modeled it indeed
>>>> as an input, and then you gave me your Reviewed-by tag.
>>>
>>> I have not misread it. Then I guess I forgot about it and missed it the
>>> next time on v3.
>>>
>>
>> Okay, that was some misunderstanding then - it's fine, no problem.
>>
>>>> Anyway - I get your concern about the previous behavior of `port`, but I chose to
>>>> model this that way purely for consistency.
>>>>
>>>> First of all - the driver(s) will check if we're feeding a full graph, as it will
>>>> indeed first check if port at 1 is present: if it is, then it follows this scheme with
>>>> port at 0 as INPUT and port at 1 as OUTPUT.
>>>> If the component in port at 0 is an OUTPUT, the bridge attach will fail.
>>>>
>>>> Getting to bindings themselves, then... it would be a mistake to model port at 0 as an
>>>> output and port at 1 as an input, because that would be not only inconsistent with the
>>>> DRM Bridge bindings, but would be highly confusing when reading the devicetree.
>>>
>>> Somewhat confusing, yes. Highly, no. Put a comment in the DT.
>>>
>>
>> "Somewhat or highly" boils down to personal opinion, so I still go for "highly"
>> but won't argue about that as wouldn't be productive and would bring us nowhere
>> anyway, so, whatever :-)
>>
>> Putting a comment in DT is an option, yes, but that comment would need to be put
>> on all of the MediaTek SoC device trees - current and future - and IMO would scream
>> "inconsistency warning" (in different words, of course) all over, which honestly
>> doesn't really look clean... at least to my eyes...
>
> What I find more confusing is my updated DT doesn't work with my
> existing kernel...
>
>>>> Please note that the bridge bindings are always declaring port at 0 as an INPUT and
>>>> other ports as OUTPUT(s).
>>>
>>> There is no guarantee on that. Port numbering is local to the bridge and
>>> opaque to anything outside that bridge. That is why you have to document
>>> what each port represents.
>>>
>>
>> I know and I agree that there's no guarantee on the numbering. I can see that in
>> other non-drm-bridge bindings, and that's fine.
>>
>>> Would we have followed that convention if all the ports were defined
>>> from the start? Certainly. But that didn't happen and you are stuck with
>>> the existing binding and ABI.
>>>
>>
>> I thought about adding a new compatible for the new port scheme, but that looked
>> even worse to me as, after doing that (yeah, I actually went for it in the first
>> version that I have never sent upstream) during my own proof-read I started
>> screaming "HACK! HACK! NOOO!" all over, and rewritten the entire thing.
>>
>>>> As an example, you can check display/bridge/analogix,anx7625.yaml or
>>>> display/bridge/samsung,mipi-dsim.yaml (and others) for bridges, otherwise
>>>> display/st,stm32mp25-lvds.yaml or display/allwinner,sun4i-a10-display-frontend.yaml
>>>> (and others) for display controllers, which do all conform to this logic, where
>>>> the input is always @0, and the output is @1.
>>>>
>>>> Of course, doing this required me to do extra changes to the MTK DRM drivers to
>>>> actually be retro-compatible with the old devicetrees as I explained before.
>>>
>>> You can't fix existing software...
>>>
>>
>> That's true, but I don't see that as an "excuse" (grant me this term please) to
>> "carelessly" keep it in a suboptimal state.
>>
>> This driver has been growing almost uncontrollably with (wrong, anyway!)
>> board-specific component vectors - and writing a new one would just add up
>> more code duplication to the mix and/or worsen the maintainability of older
>> MediaTek SoCs (as the "old" driver will get forgotten and never updated anymore).
>>
>>> If you want to break the ABI, then that's ultimately up to you and
>>> Mediatek maintainers to decide0. This case is easy to avoid, why would
>>> you knowingly break the ABI here.
>>
>> Because if we don't do this, we condemn (forever) this driver, or part of it
>> to have an inverted port scheme compared to either:
>> A. The other drm/mediatek components; or
>> B. The other bridge drivers (of which, some are used with MTK as well)
>>
>> ...and we also condemn (forever, again) all MediaTek device trees to scream
>> "port inconsistency warning: A for drm/mediatek components, B for every other
>> thing", which would scream "drm/mediatek is somewhat broken", which can be
>> avoided.
>
> Sure. The cost is just an ABI break to do that.
>
>>> OTOH, this seems like a big enough
>>> change I would imagine it is a matter of time before supporting a
>>> missing OF graph for the components will be a problem.
>>>
>>
>> Sorry I didn't understand this part, can you please-please-please reword?
>
> I think keeping the kernel working with the old and new binding will
> be a challenge. Partly because testing with the old binding won't
> happen, but also if the binding and drivers continue to evolve. So
> while maintaining old ABI might be possible with this change, it will
> continue to be an issue with each change.
That's... exactly my point, so I am happy that we agree on that.
> BTW, did you actually test
> backwards compatibility with this? I can see you fallback to the old
> binding, but there's a lot of other changes in there I can't really
> tell by looking at it.
Short answer: Yes, largely
Long answer:
Yes, with this series applied, I have tested both *old* and *new* devicetrees on
7 boards with 4 different SoCs and different display pipelines (hence, graphs):
one smartphone (MT6795), a "bunch of" Chromebooks (MT8173, MT8186, MT8195), and
a SBC (MT8195).
Of course those had DSI or eDP displays, with or without DisplayPort external
display support.
>
> What I haven't heard from you is "yes, we need to maintain the ABI" or
> "no, we can break it". Decide that, then the path here is simple.
No, we have to break it.
Cheers,
Angelo
More information about the Linux-mediatek
mailing list