[PATCH v8 6/8] i2c: of-prober: Add GPIO support to simple helpers

[Chen-Yu Tsai]

On Tue, Oct 15, 2024 at 7:19 PM Andy Shevchenko
<andriy.shevchenko at linux.intel.com> wrote:
>
> On Tue, Oct 15, 2024 at 01:31:40PM +0800, Chen-Yu Tsai wrote:
> > On Mon, Oct 14, 2024 at 7:20 PM Andy Shevchenko
> > <andriy.shevchenko at linux.intel.com> wrote:
> > > On Mon, Oct 14, 2024 at 12:06:16PM +0800, Chen-Yu Tsai wrote:
> > > > On Thu, Oct 10, 2024 at 11:20 PM Andy Shevchenko
> > > > <andriy.shevchenko at linux.intel.com> wrote:
> > > > > On Tue, Oct 08, 2024 at 03:34:25PM +0800, Chen-Yu Tsai wrote:
>
> ...
>
> > > > > > +static void i2c_of_probe_simple_disable_gpio(struct device *dev, struct i2c_of_probe_simple_ctx *ctx)
> > > > > > +{
> > > > > > +     if (!ctx->gpiod)
> > > > > > +             return;
> > > > >
> > > > > Do you need this check for the future patches?
> > > >
> > > > Not sure I follow. The check is needed because this function is called
> > > > in i2c_of_probe_simple_cleanup(), but the GPIO could have been released
> > > > earlier in i2c_of_probe_simple_cleanup_early(), and that makes this
> > > > function a no-op.
> > >
> > > Do you have a known race condition then? This is bad. You shouldn't rely on
> > > the sequence of events here, or the serialisation has to be added.
> >
> > No there isn't. Explanation below.
> >
> > > > The helpers for the release side are quite short, but the ones on the
> > > > request side wrap some conditional and error handling. I think it's
> > > > better to keep it symmetric?
> > >
> > > Yes, but why do you need the above check, I didn't still get...
> > > I.o.w. you think that there is a gap in time that (if no check) the GPIO
> > > descriptor might be changed? But then how does it affect anyway the possibility
> > > that it becomes not NULL even with the current code.
> >
> > There are two codes paths, either
> >
> >     a) successfully finding a device and enabling it, or
> >     b) exhausting all options and not finding a device, because it was
> >        optional or it is malfunctioning.
> >
> > After either code path, this cleanup function is called.
> >
> > In path (a), the GPIO descriptor is released prior to enabling the device,
> > because the descriptor is an exclusive resource, and as soon as the device
> > is enabled, its corresponding driver may probe and request the same GPIO,
> > and would fail if it was not released.
> >
> > In path (b), nothing was enabled, and the GPIO descriptor was not released
> > early.
> >
> > The cleanup function here accounts for both cases, hence the check.
>
> Yes, but the very same check is inside gpiod_set_value(). I'm still puzzled
> about the duplication. Maybe I'm missing something...

My bad. I did not check if the GPIO descriptor API had these checks.
In that case I will drop the check in this patch.


Thanks
ChenYu

> > A step-by-step description might be clearer:
> >
> > 1. i2c_of_probe_simple_enable()
> >    ...
> >    1a. i2c_of_probe_simple_get_supply()
> >    1b. i2c_of_probe_simple_get_gpiod()
> >    1c. i2c_of_probe_simple_enable_regulator()
> >    1d. i2c_of_probe_simple_set_gpio()
> >
> > 2. Loop through potential component options and probe; if one is found:
> >    2a. i2c_of_probe_simple_cleanup_early()
> >        2a-i. i2c_of_probe_simple_put_gpiod
> >    2b. Enable device and driver's probe() gets called
> >
> > 3. i2c_of_probe_simple_cleanup()
> >    3a. i2c_of_probe_simple_disable_gpio()
> >    3b. i2c_of_probe_simple_put_gpiod()
> >    3c. i2c_of_probe_simple_disable_regulator()
> >    3d. i2c_of_probe_simple_put_supply()
> >
> > > > > > +     /* Ignore error if GPIO is not in output direction */
> > > > > > +     gpiod_set_value(ctx->gpiod, !ctx->opts->gpio_assert_to_enable);
> > > > > > +}
>
> --
> With Best Regards,
> Andy Shevchenko
>
>