[PATCH v2 2/2] arm64: dts: mediatek: Add mt7986 based Bananapi R3 Mini
Frank Wunderlich
linux at fw-web.de
Thu May 9 08:21:57 PDT 2024
From: Frank Wunderlich <frank-w at public-files.de>
Add devicetree for Bananapi R3 Mini SBC.
Key features:
- MediaTek MT7986A(Filogic 830) Quad core ARM Cortex A53
- Wifi 6 2.4G/5G（MT7976C）
- 2G DDR RAM
- 8G eMMC flash
- 128MB Nand flash
- 2x 2.5GbE network port
- 1x M.2 Key B USB interface
- 1x M.2 KEY M PCIe interface
- 1x USB2.0 interface
source: https://wiki.banana-pi.org/Banana_Pi_BPI-R3_Mini
Co-developed-by: Eric Woudstra <ericwouds at gmail.com>
Signed-off-by: Eric Woudstra <ericwouds at gmail.com>
Co-developed-by: Tianling Shen <cnsztl at gmail.com>
Signed-off-by: Tianling Shen <cnsztl at gmail.com>
Signed-off-by: Frank Wunderlich <frank-w at public-files.de>
---
v2:
- add missing node for nand
- add some information about the board in description
change dts based on review from angelo+krzysztof
- drop fan status
- rename phy14 to phy0 and phy15 to phy1
- drop default-trigger from phys and so also the binding-patch
- use regulator names based on regexp regulator-[0-9]+v[0-9]+
- add comment for pwm
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 493 ++++++++++++++++++
2 files changed, 494 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 37b4ca3a87c9..1763b001ab06 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo
dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
new file mode 100644
index 000000000000..e2a2fea7adf0
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts
@@ -0,0 +1,493 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Authors: Frank Wunderlich <frank-w at public-files.de>
+ * Eric Woudstra <ericwouds at gmail.com>
+ * Tianling Shen <cnsztl at immortalwrt.org>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/mt65xx.h>
+
+#include "mt7986a.dtsi"
+
+/ {
+ model = "Bananapi BPI-R3 Mini";
+ chassis-type = "embedded";
+ compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a";
+
+ aliases {
+ serial0 = &uart0;
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dcin: regulator-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12vd";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ #cooling-cells = <2>;
+ /*
+ * The signal is inverted on this board and the PWM driver
+ * does not support polarity inversion.
+ */
+ /* cooling level (0, 1, 2) */
+ cooling-levels = <255 96 0>;
+ pwms = <&pwm 0 10000>;
+ };
+
+ reg_1p8v: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1.8vd";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&dcin>;
+ };
+
+ reg_3p3v: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3.3vd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ vin-supply = <&dcin>;
+ };
+
+ usb_vbus: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&pio 20 GPIO_ACTIVE_LOW>;
+ regulator-boot-on;
+ };
+
+ en8811_a: regulator-phy1 {
+ compatible = "regulator-fixed";
+ regulator-name = "phy1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 16 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ };
+
+ en8811_b: regulator-phy2 {
+ compatible = "regulator-fixed";
+ regulator-name = "phy2";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 17 GPIO_ACTIVE_LOW>;
+ regulator-always-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ green_led: led-0 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_POWER;
+ gpios = <&pio 19 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ reset-key {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&pio 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+};
+
+&cpu_thermal {
+ cooling-maps {
+ map0 {
+ /* active: set fan to cooling level 2 */
+ cooling-device = <&fan 2 2>;
+ trip = <&cpu_trip_active_high>;
+ };
+
+ map1 {
+ /* active: set fan to cooling level 1 */
+ cooling-device = <&fan 1 1>;
+ trip = <&cpu_trip_active_med>;
+ };
+
+ map2 {
+ /* active: set fan to cooling level 0 */
+ cooling-device = <&fan 0 0>;
+ trip = <&cpu_trip_active_low>;
+ };
+ };
+};
+
+&crypto {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ gmac0: mac at 0 {
+ compatible = "mediatek,eth-mac";
+ reg = <0>;
+ phy-mode = "2500base-x";
+ phy-handle = <&phy0>;
+ };
+
+ gmac1: mac at 1 {
+ compatible = "mediatek,eth-mac";
+ reg = <1>;
+ phy-mode = "2500base-x";
+ phy-handle = <&phy1>;
+ };
+
+ mdio: mdio-bus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_pins_default>;
+ pinctrl-1 = <&mmc0_pins_uhs>;
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+};
+
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c_pins>;
+ status = "okay";
+
+ /* MAC Address EEPROM */
+ eeprom at 50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+
+ address-width = <8>;
+ pagesize = <8>;
+ size = <256>;
+ };
+};
+
+&mdio {
+ phy0: ethernet-phy at 14 {
+ reg = <14>;
+ interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <20000>;
+ phy-mode = "2500base-x";
+ full-duplex;
+ pause;
+ airoha,pnswap-rx;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 { /* en8811_a_gpio5 */
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ default-state = "keep";
+ };
+ led at 1 { /* en8811_a_gpio4 */
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ default-state = "keep";
+ };
+ };
+ };
+
+ phy1: ethernet-phy at 15 {
+ reg = <15>;
+ interrupts-extended = <&pio 46 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&pio 47 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <20000>;
+ phy-mode = "2500base-x";
+ full-duplex;
+ pause;
+ airoha,pnswap-rx;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 { /* en8811_b_gpio5 */
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_WAN;
+ function-enumerator = <1>;
+ default-state = "keep";
+ };
+ led at 1 { /* en8811_b_gpio4 */
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_WAN;
+ function-enumerator = <2>;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pins>;
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pio {
+ i2c_pins: i2c-pins {
+ mux {
+ function = "i2c";
+ groups = "i2c";
+ };
+ };
+
+ mmc0_pins_default: mmc0-pins {
+ mux {
+ function = "emmc";
+ groups = "emmc_51";
+ };
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-ds {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ };
+
+ mmc0_pins_uhs: mmc0-uhs-pins {
+ mux {
+ function = "emmc";
+ groups = "emmc_51";
+ };
+ conf-cmd-dat {
+ pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2",
+ "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5",
+ "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD";
+ input-enable;
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ conf-clk {
+ pins = "EMMC_CK";
+ drive-strength = <6>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-ds {
+ pins = "EMMC_DSL";
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */
+ };
+ conf-rst {
+ pins = "EMMC_RSTB";
+ drive-strength = <4>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */
+ };
+ };
+
+ pcie_pins: pcie-pins {
+ mux {
+ function = "pcie";
+ groups = "pcie_clk", "pcie_wake", "pcie_pereset";
+ };
+ };
+
+ pwm_pins: pwm-pins {
+ mux {
+ function = "pwm";
+ groups = "pwm0";
+ };
+ };
+
+ spi_flash_pins: spi-flash-pins {
+ mux {
+ function = "spi";
+ groups = "spi0", "spi0_wp_hold";
+ };
+ };
+
+ usb_ngff_pins: usb-ngff-pins {
+ ngff-gnss-off-conf {
+ pins = "GPIO_6";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <1>;
+ };
+ ngff-pe-rst-conf {
+ pins = "GPIO_7";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <1>;
+ };
+ ngff-wwan-off-conf {
+ pins = "GPIO_8";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <1>;
+ };
+ ngff-pwr-off-conf {
+ pins = "GPIO_9";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <1>;
+ };
+ ngff-rst-conf {
+ pins = "GPIO_10";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <1>;
+ };
+ ngff-coex-conf {
+ pins = "SPI1_CS";
+ drive-strength = <8>;
+ mediatek,pull-up-adv = <1>;
+ };
+ };
+
+ wf_2g_5g_pins: wf-2g-5g-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_2g", "wf_5g";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+
+ wf_dbdc_pins: wf-dbdc-pins {
+ mux {
+ function = "wifi";
+ groups = "wf_dbdc";
+ };
+ conf {
+ pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+ "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+ "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+ "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+ "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+ "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+ "WF1_TOP_CLK", "WF1_TOP_DATA";
+ drive-strength = <4>;
+ };
+ };
+
+ wf_led_pins: wf-led-pins {
+ mux {
+ function = "led";
+ groups = "wifi_led";
+ };
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pins>;
+ status = "okay";
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi_flash_pins>;
+ status = "okay";
+
+ flash at 0 {
+ compatible = "spi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+
+ spi-max-frequency = <20000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ };
+};
+
+&ssusb {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_ngff_pins>;
+ vusb33-supply = <®_3p3v>;
+ vbus-supply = <&usb_vbus>;
+ status = "okay";
+};
+
+&trng {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&watchdog {
+ status = "okay";
+};
+
+&wifi {
+ status = "okay";
+ pinctrl-names = "default", "dbdc";
+ pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>;
+ pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>;
+
+ led {
+ led-active-low;
+ };
+};
+
--
2.34.1
More information about the Linux-mediatek
mailing list