[PATCH] arm64: dts: mediatek: mt8195: Add missing clock for xhci1 controller
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Mon Jul 29 05:34:27 PDT 2024
Il 29/07/24 12:48, Chen-Yu Tsai ha scritto:
> On Mon, Jul 29, 2024 at 4:54 PM AngeloGioacchino Del Regno
> <angelogioacchino.delregno at collabora.com> wrote:
>>
>> Il 29/07/24 10:07, Chen-Yu Tsai ha scritto:
>>> On Mon, Jul 29, 2024 at 3:59 PM AngeloGioacchino Del Regno
>>> <angelogioacchino.delregno at collabora.com> wrote:
>>>>
>>>> Il 26/07/24 17:11, Chen-Yu Tsai ha scritto:
>>>>> On Fri, Jul 26, 2024 at 8:11 PM AngeloGioacchino Del Regno
>>>>> <angelogioacchino.delregno at collabora.com> wrote:
>>>>>>
>>>>>> Il 25/07/24 12:34, Chen-Yu Tsai ha scritto:
>>>>>>> Hi,
>>>>>>>
>>>>>>> On Mon, Jul 22, 2024 at 11:27 PM Nícolas F. R. A. Prado
>>>>>>> <nfraprado at collabora.com> wrote:
>>>>>>>>
>>>>>>>> Currently if the xhci1 controller happens to probe before the pcie1
>>>>>>>> controller then it fails with the following errors:
>>>>>>>>
>>>>>>>> xhci-mtk 11290000.usb: clocks are not stable (0x1003d0f)
>>>>>>>> xhci-mtk 11290000.usb: can't setup: -110
>>>>>>>> xhci-mtk: probe of 11290000.usb failed with error -110
>>>>>>>>
>>>>>>>> The issue has been tracked down to the CLK_INFRA_AO_PCIE_P1_TL_96M
>>>>>>>> clock, although exactly why this pcie clock is needed for the usb
>>>>>>>> controller is still unknown. Add the clock to the xhci1 controller so it
>>>>>>>> always probes successfully and use a placeholder clock name for it.
>>>>>>>>
>>>>>>>> Reported-by: Nícolas F. R. A. Prado <nfraprado at collabora.com> #KernelCI
>>>>>>>> Closes: https://lore.kernel.org/all/9fce9838-ef87-4d1b-b3df-63e1ddb0ec51@notapiano/
>>>>>>>> Signed-off-by: Nícolas F. R. A. Prado <nfraprado at collabora.com>
>>>>>>>
>>>>>>> So I asked MediaTek about this, and it seems the correct thing to do is
>>>>>>> disable USB 3 on this host controller using the following snippet. The
>>>>>>> snippet is copy-pasted from our issue tracker and won't apply directly.
>>>>>>>
>>>>>>> This is also seen in mt8395-kontron-3-5-sbc-i1200.dts, on which xhci1
>>>>>>> is used only for USB 2.0 on an M.2 slot.
>>>>>>>
>>>>>>
>>>>>> Uhm, okay, but why should USB3 be disabled on a controller that supports USB3?
>>>>>>
>>>>>> I agree about disabling it on specific boards that use only the USB 2.0 lines of
>>>>>> this controller, but doing that globally looks wrong... and looks like being a
>>>>>> workaround for an error that gets solved with adding a clock as well.
>>>>>>
>>>>>> In short, the question is: why would that be the correct thing to do?
>>>>>
>>>>> We can disable it in mt8195-cherry.dtsi then?
>>>>
>>>> That device does not use this controller, so yes we can disable it, but that still
>>>> doesn't resolve the issue pointed out by Nicolas...!
>>>
>>> No. I mean disable USB3 on this port. Also see the next paragraph.
>>>
>>
>> Yes, sorry I was meaning the same - but I effectively wrote "disable controller"
>> instead, my bad.
>>
>>>> Please note that the issue that he sees doesn't happen only on Tomato, but also on
>>>> other MediaTek MT8195/MT8395 boards - and applying this commit makes disabling the
>>>> controller, or disabling the USB 3 lines on the controller, kinda redundant, as
>>>> this will effectively fix probing it... but again, fixing the actual issue with
>>>> this controller is something that must be done.
>>>
>>> If those other boards use the XHCI1 USB3 lines for ... USB3, then the USB3
>>> PHY should also be tied to XHCI1, right now due to the Cherry Chromebook
>>> design, only the USB2 PHY is tied to it.
>>>
>>
>> Yes, I am aware of that.
>>
>>>> Disabling the controller on Tomato is a different topic - here we are discussing
>>>> about fixing the issue, and that will happen, again, on any board that has this
>>>> controller enabled with USB3 lines. :-)
>>>>
>>>> So, unless there is any specific reason for which applying this commit is a bad
>>>> idea, or any alternative fix to this that is better than the proposed one, and
>>>> not a workaround... I'm applying this one.
>>>
>>> Didn't I just relay what MediaTek says is the correct fix? Disable USB3
>>> for this port on devices where the serial pairs are used for PCIe instead
>>> of USB3.
>>>
>>
>> I think there must've been some misunderstanding here.
>>
>> Yes you did relay what MediaTek is the correct fix, and I agree that the USB3 must
>> be disabled on devices where those serial pairs are used for PCIe instead of USB,
>> or on devices where those are completely unused.
>
> OK. I will send a patch for Tomato as you asked.
>
>> This, though, will fix the issue only on those devices (because we are disabling
>> those lines entirely, so depending on how we see it, this might not be a fix but
>> rather a workaround).
>
> I would say that is a more accurate description of the hardware, so a fix.
>
I can accept a patch for Tomato with a Fixes tag. Yes.
>> If we don't apply this fix, any board that uses those pairs for USB 3 instead will
>> still show the same "clocks are not stable" error, leaving them with a broken port.
>>
>> And I believe that because the clocks are not routed externally but rather are
>> internal to the SoC, so, if INFRA_AO_PCIE_P1_TL_96M is necessary for that USB 3
>> port to work, a board that intends to use those pairs for USB3 would still need
>> this exact clock to actually get that port to work.
>
> I couldn't reproduce the issue by disabling pcie1 as Nicolas mentioned.
> I don't have any more to add to this though. Sorry for the noise.
>
Sometimes the noise actually opens some eyes around (be it mine or whoever else's),
so as long as it is constructive, I don't see it as noise.
In short: no worries! :-)
>> As for Tomato itself - I agree that we must add the u3p-dis-msk=0x1 flag, yes,
>> and we will, but I'm purely talking about - again - an eventual board that would
>> not have that property because USB3 is exposed/used for real.
>
> I think it would make more sense to fix the `phys = ` statement in mt8195.dtsi
> to list both the USB2 and USB3 PHYs. At the board level, for boards only
> using USB2, we would have the overriding `phys = ` statement alongside the
> `mediatek,u3p-dis-mask` property. Does that make sense to you?
>
Yeah, that'd make sense, though I'm not sure if the driver can cope with that: in
that case, we'd obviously need "two" patches and not one :-)
Cheers!
>
> Thanks
> ChenYu
>
>> Cheers,
>> Angelo
>>
>>>
>>> Regards
>>> ChenYu
>>>
>>>> Cheers,
>>>> Angelo
>>>>
>>>>>
>>>>> ChenYu
>>>>>
>>>>>> Cheers,
>>>>>> Angelo
>>>>>>
>>>>>>>
>>>>>>> ChenYu
>>>>>>>
>>>>>>> index 8b7307cdefc6..2dac9f706a58
>>>>>>> --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
>>>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
>>>>>>> @@ -1447,6 +1447,7 @@
>>>>>>> "xhci_ck";
>>>>>>> mediatek,syscon-wakeup = <&pericfg 0x400 104>;
>>>>>>> wakeup-source;
>>>>>>> + mediatek,u3p-dis-msk = <0x1>;
>>>>>>> status = "disabled";
>>>>>>> };
>>>>>>>
>>>>>>>> ---
>>>>>>>> arch/arm64/boot/dts/mediatek/mt8195.dtsi | 10 ++++++++--
>>>>>>>> 1 file changed, 8 insertions(+), 2 deletions(-)
>>>>>>>>
>>>>>>>> diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
>>>>>>>> index 2ee45752583c..cc5169871f1c 100644
>>>>>>>> --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi
>>>>>>>> +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
>>>>>>>> @@ -1453,9 +1453,15 @@ xhci1: usb at 11290000 {
>>>>>>>> <&topckgen CLK_TOP_SSUSB_P1_REF>,
>>>>>>>> <&apmixedsys CLK_APMIXED_USB1PLL>,
>>>>>>>> <&clk26m>,
>>>>>>>> - <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>;
>>>>>>>> + <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>,
>>>>>>>> + /*
>>>>>>>> + * This clock is required due to a hardware
>>>>>>>> + * bug. The 'frmcnt_ck' clock name is used as a
>>>>>>>> + * placeholder.
>>>>>>>> + */
>>>>>>>> + <&infracfg_ao CLK_INFRA_AO_PCIE_P1_TL_96M>;
>>>>>>>> clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck",
>>>>>>>> - "xhci_ck";
>>>>>>>> + "xhci_ck", "frmcnt_ck";
>>>>>>>> mediatek,syscon-wakeup = <&pericfg 0x400 104>;
>>>>>>>> wakeup-source;
>>>>>>>> status = "disabled";
>>>>>>>>
>>>>>>>> ---
>>>>>>>> base-commit: dee7f101b64219f512bb2f842227bd04c14efe30
>>>>>>>> change-id: 20240722-usb-1129-probe-pci-clk-fix-ef8646f46aac
>>>>>>>>
>>>>>>>> Best regards,
>>>>>>>> --
>>>>>>>> Nícolas F. R. A. Prado <nfraprado at collabora.com>
>>>>>>>>
>>>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>
>>
More information about the Linux-mediatek
mailing list