[PATCH net v4] net: dsa: mt7530: fix impossible MDIO address and issue warning

Daniel Golle daniel at makrotopia.org
Thu Jul 4 08:08:22 PDT 2024


The MDIO address of the MT7530 and MT7531 switch ICs can be configured
using bootstrap pins. However, there are only 4 possible options for the
switch itself: 7, 15, 23 and 31. As in MediaTek's SDK the address of the
switch is wrongly stated in the device tree as 0 (while in reality it is
31), warn the user about such broken device tree and make a good guess
what was actually intended.

This is imporant also to not break compatibility with older Device Trees
as with commit 868ff5f4944a ("net: dsa: mt7530-mdio: read PHY address of
switch from device tree") the address in device tree will be taken into
account, while before it was hard-coded to 0x1f.

Fixes: b8f126a8d543 ("net-next: dsa: add dsa support for Mediatek MT7530 switch")
Signed-off-by: Daniel Golle <daniel at makrotopia.org>
Reviewed-by: Andrew Lunn <andrew at lunn.ch>
Tested-by: Arınç ÜNAL <arinc.unal at arinc9.com>
Reviewed-by: Arınç ÜNAL <arinc.unal at arinc9.com>
---
Changes since v3 [3]:
 - simplify calculation of correct address

Changes since v2 [2]:
 - use macros instead of magic numbers
 - introduce helper functions
 - register new device on MDIO bus instead of messing with the address
   and schedule delayed_work to unregister the "wrong" device.
   This is a slightly different approach than suggested by Russell, but
   imho makes things much easier than keeping the "wrong" device and
   having to deal with keeping the removal of both devices linked.
 - improve comments

Changes since v1 [1]:
 - use FW_WARN as suggested.
 - fix build on net tree which doesn't have 'mdiodev' as member of the
   priv struct. Imho including this patch as fix makes sense to warn
   users about broken firmware, even if the change introducing the
   actual breakage is only present in net-next for now.

[1]: https://patchwork.kernel.org/project/netdevbpf/patch/e615351aefba25e990215845e4812e6cb8153b28.1714433716.git.daniel@makrotopia.org/
[2]: https://patchwork.kernel.org/project/netdevbpf/patch/11f5f127d0350e72569c36f9060b6e642dfaddbb.1714514208.git.daniel@makrotopia.org/
[3]: https://patchwork.kernel.org/project/netdevbpf/patch/7e3fed489c0bbca84a386b1077c61589030ff4ab.1719963228.git.daniel@makrotopia.org/

 drivers/net/dsa/mt7530-mdio.c | 91 +++++++++++++++++++++++++++++++++++
 1 file changed, 91 insertions(+)

diff --git a/drivers/net/dsa/mt7530-mdio.c b/drivers/net/dsa/mt7530-mdio.c
index 51df42ccdbe6..2037ed944801 100644
--- a/drivers/net/dsa/mt7530-mdio.c
+++ b/drivers/net/dsa/mt7530-mdio.c
@@ -11,6 +11,7 @@
 #include <linux/regmap.h>
 #include <linux/reset.h>
 #include <linux/regulator/consumer.h>
+#include <linux/workqueue.h>
 #include <net/dsa.h>
 
 #include "mt7530.h"
@@ -136,6 +137,92 @@ static const struct of_device_id mt7530_of_match[] = {
 };
 MODULE_DEVICE_TABLE(of, mt7530_of_match);
 
+static int
+mt7530_correct_addr(int phy_addr)
+{
+	/* The corrected address is calculated as stated below:
+	 * 0~6, 31 -> 31
+	 * 7~14    -> 7
+	 * 15~22   -> 15
+	 * 23~30   -> 23
+	 */
+return (phy_addr - MT7530_NUM_PORTS & ~MT7530_NUM_PORTS) + MT7530_NUM_PORTS & PHY_MAX_ADDR - 1;
+}
+
+static bool
+mt7530_is_invalid_addr(int phy_addr)
+{
+	/* Only MDIO bus addresses 7, 15, 23, and 31 are valid options,
+	 * which all have the least significant three bits set. Check
+	 * for this.
+	 */
+	return (phy_addr & MT7530_NUM_PORTS) != MT7530_NUM_PORTS;
+}
+
+struct remove_impossible_priv {
+	struct delayed_work remove_impossible_work;
+	struct mdio_device *mdiodev;
+};
+
+static void
+mt7530_remove_impossible(struct work_struct *work)
+{
+	struct remove_impossible_priv *priv = container_of(work, struct remove_impossible_priv,
+							   remove_impossible_work.work);
+	struct mdio_device *mdiodev = priv->mdiodev;
+
+	mdio_device_remove(mdiodev);
+	mdio_device_free(mdiodev);
+	kfree(priv);
+}
+
+static int
+mt7530_reregister(struct mdio_device *mdiodev)
+{
+	/* If the address in DT must be wrong, make a good guess about
+	 * the most likely intention, issue a warning, register a new
+	 * MDIO device at the correct address and schedule the removal
+	 * of the device having an impossible address.
+	 */
+	struct fwnode_handle *fwnode = dev_fwnode(&mdiodev->dev);
+	int corrected_addr = mt7530_correct_addr(mdiodev->addr);
+	struct remove_impossible_priv *rem_priv;
+	struct mdio_device *new_mdiodev;
+	int ret;
+
+	rem_priv = kmalloc(sizeof(*rem_priv), GFP_KERNEL);
+	if (!rem_priv)
+		return -ENOMEM;
+
+	new_mdiodev = mdio_device_create(mdiodev->bus, corrected_addr);
+	if (IS_ERR(new_mdiodev)) {
+		ret = PTR_ERR(new_mdiodev);
+		goto out_free_work;
+	}
+	device_set_node(&new_mdiodev->dev, fwnode);
+
+	ret = mdio_device_register(new_mdiodev);
+	if (WARN_ON(ret))
+		goto out_free_dev;
+
+	dev_warn(&mdiodev->dev, FW_WARN
+		 "impossible switch MDIO address in device tree, assuming %d\n",
+		 corrected_addr);
+
+	/* schedule impossible device for removal from mdio bus */
+	rem_priv->mdiodev = mdiodev;
+	INIT_DELAYED_WORK(&rem_priv->remove_impossible_work, mt7530_remove_impossible);
+	schedule_delayed_work(&rem_priv->remove_impossible_work, 0);
+
+	return -EFAULT;
+
+out_free_dev:
+	mdio_device_free(new_mdiodev);
+out_free_work:
+	kfree(rem_priv);
+	return ret;
+}
+
 static int
 mt7530_probe(struct mdio_device *mdiodev)
 {
@@ -144,6 +231,10 @@ mt7530_probe(struct mdio_device *mdiodev)
 	struct device_node *dn;
 	int ret;
 
+	/* Check and if needed correct the MDIO address of the switch */
+	if (mt7530_is_invalid_addr(mdiodev->addr))
+		return mt7530_reregister(mdiodev);
+
 	dn = mdiodev->dev.of_node;
 
 	priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL);
-- 
2.45.2




More information about the Linux-mediatek mailing list