[PATCH net-next v2 5/7] net: dsa: mt7530: simplify mt7530_setup_port6() and change to void

Daniel Golle daniel at makrotopia.org
Tue Jan 30 07:59:28 PST 2024


On Tue, Jan 30, 2024 at 06:20:51PM +0300, Arınç ÜNAL via B4 Relay wrote:
> From: Arınç ÜNAL <arinc.unal at arinc9.com>
> 
> This code is from before this driver was converted to phylink API. Phylink
> deals with the unsupported interface cases before mt7530_setup_port6() is
> run. Therefore, the default case would never run. However, it must be
> defined nonetheless to handle all the remaining enumeration values, the
> phy-modes.
> 
> Switch to if statement for RGMII and return which simplifies the code and
> saves an indent.
> 
> Set P6_INTF_MODE, which is the the three least significant bits of the
> MT7530_P6ECR register, to 0 for RGMII even though it will already be 0
> after reset. This is to keep supporting dynamic reconfiguration of the port
> in the case the interface changes from TRGMII to RGMII. The core operations
> for TRGMII does not interfere with RGMII so no need to undo them.

That last sentence doesn't parse English gramar.
"operations": plural
"does": singular

Should probably be either "The core operation for TRGMII does not..."
or "The core operations for TRGMII do not..."

As you are mentioning it, I'm now curious if you consider to
dynamically reconfiguring TRGIII<->RGMII on port 6 depending on
whether there is more then 1 GBit/s possible bandwidth needed between
port 6 and the remaining ports? That could make sense for power
management, but then we should at least again switch off the TRGMII
clocks in the RGMII case before returning, see my suggestion inline
below.

> 
> Read XTAL after checking for RGMII as it's only needed for the TRGMII
> interface mode.
> 
> Change mt7530_setup_port6() to void now that there're no error cases left.
> 
> Signed-off-by: Arınç ÜNAL <arinc.unal at arinc9.com>

Reviewed-by: Daniel Golle <daniel at makrotopia.org>

> ---
>  drivers/net/dsa/mt7530.c | 103 ++++++++++++++++++++---------------------------
>  1 file changed, 43 insertions(+), 60 deletions(-)
> 
> diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
> index c4d492e29fdf..36dc2bbcf3b6 100644
> --- a/drivers/net/dsa/mt7530.c
> +++ b/drivers/net/dsa/mt7530.c
> @@ -414,70 +414,57 @@ mt753x_preferred_default_local_cpu_port(struct dsa_switch *ds)
>  }
>  
>  /* Setup port 6 interface mode and TRGMII TX circuit */
> -static int
> +static void
>  mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
>  {
>  	struct mt7530_priv *priv = ds->priv;
> -	u32 ncpo1, ssc_delta, trgint, xtal;
> -
> -	xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
> +	u32 ncpo1, ssc_delta, xtal;
>  
> -	switch (interface) {
> -	case PHY_INTERFACE_MODE_RGMII:
> -		trgint = 0;
> -		break;
> -	case PHY_INTERFACE_MODE_TRGMII:
> -		trgint = 1;
> -		if (xtal == HWTRAP_XTAL_25MHZ)
> -			ssc_delta = 0x57;
> -		else
> -			ssc_delta = 0x87;
> -		if (priv->id == ID_MT7621) {
> -			/* PLL frequency: 125MHz: 1.0GBit */
> -			if (xtal == HWTRAP_XTAL_40MHZ)
> -				ncpo1 = 0x0640;
> -			if (xtal == HWTRAP_XTAL_25MHZ)
> -				ncpo1 = 0x0a00;
> -		} else { /* PLL frequency: 250MHz: 2.0Gbit */
> -			if (xtal == HWTRAP_XTAL_40MHZ)
> -				ncpo1 = 0x0c80;
> -			if (xtal == HWTRAP_XTAL_25MHZ)
> -				ncpo1 = 0x1400;
> -		}
> -		break;
> -	default:
> -		dev_err(priv->dev, "xMII interface %d not supported\n",
> -			interface);
> -		return -EINVAL;
> +	if (interface == PHY_INTERFACE_MODE_RGMII) {
> +		mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
> +			   P6_INTF_MODE(0));

Maybe at least switch off TRGMIICK here because we are sure we don't need it
in the RGMII case, ie:
core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);

And that then is another line of code already present just below which
means you could keep variable trgint as it was and return after
switching off TRGMIICK below anyway...

> +		return;
>  	}
>  
> -	mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK,
> -		   P6_INTF_MODE(trgint));
> +	mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK, P6_INTF_MODE(1));
>  
> -	if (trgint) {
> -		/* Disable the MT7530 TRGMII clocks */
> -		core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
> +	xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
>  
> -		/* Setup the MT7530 TRGMII Tx Clock */
> -		core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
> -		core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
> -		core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
> -		core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
> -		core_write(priv, CORE_PLL_GROUP4,
> -			   RG_SYSPLL_DDSFBK_EN | RG_SYSPLL_BIAS_EN |
> -			   RG_SYSPLL_BIAS_LPF_EN);
> -		core_write(priv, CORE_PLL_GROUP2,
> -			   RG_SYSPLL_EN_NORMAL | RG_SYSPLL_VODEN |
> -			   RG_SYSPLL_POSDIV(1));
> -		core_write(priv, CORE_PLL_GROUP7,
> -			   RG_LCDDS_PCW_NCPO_CHG | RG_LCCDS_C(3) |
> -			   RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
> +	if (xtal == HWTRAP_XTAL_25MHZ)
> +		ssc_delta = 0x57;
> +	else
> +		ssc_delta = 0x87;
>  
> -		/* Enable the MT7530 TRGMII clocks */
> -		core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
> +	if (priv->id == ID_MT7621) {
> +		/* PLL frequency: 125MHz: 1.0GBit */
> +		if (xtal == HWTRAP_XTAL_40MHZ)
> +			ncpo1 = 0x0640;
> +		if (xtal == HWTRAP_XTAL_25MHZ)
> +			ncpo1 = 0x0a00;
> +	} else { /* PLL frequency: 250MHz: 2.0Gbit */
> +		if (xtal == HWTRAP_XTAL_40MHZ)
> +			ncpo1 = 0x0c80;
> +		if (xtal == HWTRAP_XTAL_25MHZ)
> +			ncpo1 = 0x1400;
>  	}
>  
> -	return 0;
> +	/* Disable the MT7530 TRGMII clocks */
> +	core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);

... by moving this line up and letting it happen unconditionally for
both RGMII and TRGMII (in case that works and doesn't break the RGMII
case, but I assume it doesn't)

> +
> +	/* Setup the MT7530 TRGMII Tx Clock */
> +	core_write(priv, CORE_PLL_GROUP5, RG_LCDDS_PCW_NCPO1(ncpo1));
> +	core_write(priv, CORE_PLL_GROUP6, RG_LCDDS_PCW_NCPO0(0));
> +	core_write(priv, CORE_PLL_GROUP10, RG_LCDDS_SSC_DELTA(ssc_delta));
> +	core_write(priv, CORE_PLL_GROUP11, RG_LCDDS_SSC_DELTA1(ssc_delta));
> +	core_write(priv, CORE_PLL_GROUP4, RG_SYSPLL_DDSFBK_EN |
> +		   RG_SYSPLL_BIAS_EN | RG_SYSPLL_BIAS_LPF_EN);
> +	core_write(priv, CORE_PLL_GROUP2, RG_SYSPLL_EN_NORMAL |
> +		   RG_SYSPLL_VODEN | RG_SYSPLL_POSDIV(1));
> +	core_write(priv, CORE_PLL_GROUP7, RG_LCDDS_PCW_NCPO_CHG |
> +		   RG_LCCDS_C(3) | RG_LCDDS_PWDB | RG_LCDDS_ISO_EN);
> +
> +	/* Enable the MT7530 TRGMII clocks */
> +	core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_TRGMIICK_EN);
>  }
>  
>  static void
> @@ -2609,15 +2596,11 @@ mt7530_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
>  		  phy_interface_t interface)
>  {
>  	struct mt7530_priv *priv = ds->priv;
> -	int ret;
>  
> -	if (port == 5) {
> +	if (port == 5)
>  		mt7530_setup_port5(priv->ds, interface);
> -	} else if (port == 6) {
> -		ret = mt7530_setup_port6(priv->ds, interface);
> -		if (ret)
> -			return ret;
> -	}
> +	else if (port == 6)
> +		mt7530_setup_port6(priv->ds, interface);
>  
>  	return 0;
>  }
> 
> -- 
> 2.40.1
> 
> 



More information about the Linux-mediatek mailing list