[PATCH v4 5/5] arm64: dts: mediatek: mt8365: Add support for camera

[Laurent Pinchart]

Hi Julien,

Thank you for the patch.

On Wed, Jan 10, 2024 at 03:14:42PM +0100, Julien Stephan wrote:
> Add base support for cameras for mt8365 platforms. This requires nodes
> for the sensor interface, camsv, and CSI receivers.
> 
> Signed-off-by: Julien Stephan <jstephan at baylibre.com>
> ---
>  arch/arm64/boot/dts/mediatek/mt8365.dtsi | 128 +++++++++++++++++++++++
>  1 file changed, 128 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8365.dtsi b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> index 24581f7410aa..9059b2f83b83 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8365.dtsi
> @@ -10,6 +10,7 @@
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/phy/phy.h>
>  #include <dt-bindings/power/mediatek,mt8365-power.h>
> +#include <dt-bindings/memory/mediatek,mt8365-larb-port.h>
>  
>  / {
>  	compatible = "mediatek,mt8365";
> @@ -703,6 +704,133 @@ ethernet: ethernet at 112a0000 {
>  			status = "disabled";
>  		};
>  
> +		camsv1: camsv at 15050000 {
> +			compatible = "mediatek,mt8365-camsv";
> +			reg = <0 0x15050000 0 0x0040>,
> +			      <0 0x15050208 0 0x0020>,
> +			      <0 0x15050400 0 0x0100>;
> +			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&camsys CLK_CAM>,
> +				 <&camsys CLK_CAMTG>,
> +				 <&camsys CLK_CAMSV0>;
> +			clock-names = "cam", "camtg", "camsv";
> +			iommus = <&iommu M4U_PORT_CAM_IMGO>;
> +			mediatek,larb = <&larb2>;
> +			power-domains = <&spm MT8365_POWER_DOMAIN_CAM>;
> +			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				port at 0 {
> +					reg = <0>;
> +					camsv1_endpoint: endpoint {
> +						remote-endpoint =
> +							<&seninf_camsv1_endpoint>;

I think you can keep this on a single line. Same below.

> +					};
> +				};
> +			};
> +		};
> +
> +		camsv2: camsv at 15050800 {
> +			compatible = "mediatek,mt8365-camsv";
> +			reg = <0 0x15050800 0 0x0040>,
> +			      <0 0x15050228 0 0x0020>,
> +			      <0 0x15050C00 0 0x0100>;

Lower-case hex constants.

> +			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&camsys CLK_CAM>,
> +				 <&camsys CLK_CAMTG>,
> +				 <&camsys CLK_CAMSV1>;
> +			clock-names = "cam", "camtg", "camsv";
> +			iommus = <&iommu M4U_PORT_CAM_IMGO>;
> +

Nitpicking, camsv doesn't have a blank line here. I'm fine either way,
but please do the same for both nodes.

> +			mediatek,larb = <&larb2>;
> +			power-domains = <&spm MT8365_POWER_DOMAIN_CAM>;
> +			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				port at 0 {
> +					reg = <0>;
> +					camsv2_endpoint: endpoint {
> +						remote-endpoint =
> +							<&seninf_camsv2_endpoint>;
> +					};
> +				};
> +			};
> +		};
> +
> +		seninf: seninf at 15040000 {

This should go before the two camsv instances to keep nodes sorted by
address. The camsv1, camsv2 and seninf nodes need to be moved further
down for the same reason.

> +			compatible = "mediatek,mt8365-seninf";
> +			reg = <0 0x15040000 0 0x6000>;
> +			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_LOW>;
> +			clocks = <&camsys CLK_CAM_SENIF>,
> +				 <&topckgen CLK_TOP_SENIF_SEL>;
> +			clock-names = "camsys", "top_mux";
> +
> +			power-domains = <&spm MT8365_POWER_DOMAIN_CAM>;
> +
> +			phys = <&mipi_csi0 PHY_TYPE_DPHY>, <&mipi_csi1>;
> +			phy-names = "csi0", "csi1";
> +
> +			status = "disabled";
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				port at 0 {
> +					reg = <0>;
> +				};
> +
> +				port at 1 {
> +					reg = <1>;
> +				};
> +
> +				port at 2 {
> +					reg = <2>;
> +				};
> +
> +				port at 3 {
> +					reg = <3>;
> +				};
> +
> +				port at 4 {
> +					reg = <4>;
> +					seninf_camsv1_endpoint: endpoint {
> +						remote-endpoint =
> +							<&camsv1_endpoint>;
> +					};
> +				};
> +
> +				port at 5 {
> +					reg = <5>;
> +					seninf_camsv2_endpoint: endpoint {
> +						remote-endpoint =
> +							<&camsv2_endpoint>;
> +					};
> +				};
> +			};
> +		};
> +
> +		mipi_csi0: mipi-csi0 at 11c10000 {
> +			compatible = "mediatek,mt8365-csi-rx";
> +			reg = <0 0x11C10000 0 0x2000>;

Lower-case hex constants.

> +			status = "disabled";
> +			num-lanes = <4>;
> +			#phy-cells = <1>;
> +		};
> +
> +		mipi_csi1: mipi-csi1 at 11c12000 {
> +			compatible = "mediatek,mt8365-csi-rx";
> +			reg = <0 0x11C12000 0 0x2000>;

Lower-case hex constants.

Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>

> +			phy-type = <PHY_TYPE_DPHY>;
> +			status = "disabled";
> +			num-lanes = <4>;
> +			#phy-cells = <0>;
> +		};
> +
>  		u3phy: t-phy at 11cc0000 {
>  			compatible = "mediatek,mt8365-tphy", "mediatek,generic-tphy-v2";
>  			#address-cells = <1>;

-- 
Regards,

Laurent Pinchart