[PATCH v2 2/2] arm64: dts: mediatek: add Kontron 3.5"-SBC-i1200
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Mon Feb 19 02:00:34 PST 2024
Il 19/02/24 09:44, Michael Walle ha scritto:
> Add basic support for the Kontron 3.5" single board computer featuring a
> Mediatek i1200 SoC (MT8395/MT8195).
>
> Signed-off-by: Michael Walle <mwalle at kernel.org>
> ---
> v2:
> - none
>
> arch/arm64/boot/dts/mediatek/Makefile | 1 +
> .../mediatek/mt8395-kontron-3-5-sbc-i1200.dts | 1091 +++++++++++++++++
> 2 files changed, 1092 insertions(+)
> create mode 100644 arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts
>
> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> index 37b4ca3a87c9..697b6b5de3cb 100644
> --- a/arch/arm64/boot/dts/mediatek/Makefile
> +++ b/arch/arm64/boot/dts/mediatek/Makefile
> @@ -76,5 +76,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-genio-1200-evk.dtb
> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-kontron-3-5-sbc-i1200.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-radxa-nio-12l.dtb
> dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
> diff --git a/arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts b/arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts
> new file mode 100644
> index 000000000000..0c634bc8776c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/mediatek/mt8395-kontron-3-5-sbc-i1200.dts
> @@ -0,0 +1,1091 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Copyright (C) 2024 Kontron Europe GmbH
> + *
> + * Author: Michael Walle <mwalle at kernel.org>
> + */
> +/dts-v1/;
> +
> +#include "mt8195.dtsi"
> +#include "mt6359.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
> +#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
> +#include <dt-bindings/spmi/spmi.h>
> +
> +/ {
> + model = "Kontron 3.5\"-SBC-i1200";
> + compatible = "kontron,3-5-sbc-i1200", "mediatek,mt8395", "mediatek,mt8195";
> +
> + aliases {
> + mmc0 = &mmc0;
> + mmc1 = &mmc1;
> + serial0 = &uart1;
> + serial1 = &uart2;
> + serial2 = &uart3;
> + serial3 = &uart4;
> + serial4 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + firmware {
> + optee {
> + compatible = "linaro,optee-tz";
> + method = "smc";
> + };
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&gpio_keys_pins>;
> +
> + key-0 {
> + gpios = <&pio 106 GPIO_ACTIVE_LOW>;
> + label = "volume_up";
> + linux,code = <KEY_VOLUMEUP>;
> + wakeup-source;
> + debounce-interval = <15>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_pins>;
> +
> + led-0 {
> + gpios = <&pio 107 GPIO_ACTIVE_HIGH>;
> + default-state = "keep";
> + function = LED_FUNCTION_POWER;
> + color = <LED_COLOR_ID_GREEN>;
> + };
> + };
> +
> + memory at 40000000 {
> + device_type = "memory";
> + reg = <0 0x40000000 0x0 0x80000000>;
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /*
> + * 12 MiB reserved for OP-TEE (BL32)
> + * +-----------------------+ 0x43e0_0000
> + * | SHMEM 2MiB |
> + * +-----------------------+ 0x43c0_0000
> + * | | TA_RAM 8MiB |
> + * + TZDRAM +--------------+ 0x4340_0000
> + * | | TEE_RAM 2MiB |
> + * +-----------------------+ 0x4320_0000
> + */
> + optee_reserved: optee at 43200000 {
> + no-map;
> + reg = <0 0x43200000 0 0x00c00000>;
> + };
> +
> + scp_mem: memory at 50000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x50000000 0 0x2900000>;
> + no-map;
> + };
> +
> + vpu_mem: memory at 53000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x53000000 0 0x1400000>; /* 20 MB */
> + };
> +
> + /* 2 MiB reserved for ARM Trusted Firmware (BL31) */
> + bl31_secmon_mem: memory at 54600000 {
> + no-map;
> + reg = <0 0x54600000 0x0 0x200000>;
> + };
> +
> + snd_dma_mem: memory at 60000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x60000000 0 0x1100000>;
> + no-map;
> + };
> +
> + apu_mem: memory at 62000000 {
> + compatible = "shared-dma-pool";
> + reg = <0 0x62000000 0 0x1400000>; /* 20 MB */
> + };
> + };
> +
> + thermal_sensor0: thermal-sensor-0 {
> + compatible = "generic-adc-thermal";
> + #thermal-sensor-cells = <0>;
> + io-channels = <&auxadc 0>;
> + io-channel-names = "sensor-channel";
> + temperature-lookup-table = <(-25000) 1474
> + (-20000) 1374
> + (-15000) 1260
> + (-10000) 1134
> + (-5000) 1004
> + 0 874
> + 5000 750
> + 10000 635
> + 15000 532
> + 20000 443
> + 25000 367
> + 30000 303
> + 35000 250
> + 40000 206
> + 45000 170
> + 50000 141
> + 55000 117
> + 60000 97
> + 65000 81
> + 70000 68
> + 75000 57
> + 80000 48
> + 85000 41
> + 90000 35
> + 95000 30
> + 100000 25
> + 105000 22
> + 110000 19
> + 115000 16
> + 120000 14
> + 125000 12
> + 130000 10
> + 135000 9
> + 140000 8
> + 145000 7
> + 150000 6>;
> + };
> +
> + thermal_sensor1: thermal-sensor-1 {
> + compatible = "generic-adc-thermal";
> + #thermal-sensor-cells = <0>;
> + io-channels = <&auxadc 1>;
> + io-channel-names = "sensor-channel";
> + temperature-lookup-table = <(-25000) 1474
> + (-20000) 1374
> + (-15000) 1260
> + (-10000) 1134
> + (-5000) 1004
> + 0 874
> + 5000 750
> + 10000 635
> + 15000 532
> + 20000 443
> + 25000 367
> + 30000 303
> + 35000 250
> + 40000 206
> + 45000 170
> + 50000 141
> + 55000 117
> + 60000 97
> + 65000 81
> + 70000 68
> + 75000 57
> + 80000 48
> + 85000 41
> + 90000 35
> + 95000 30
> + 100000 25
> + 105000 22
> + 110000 19
> + 115000 16
> + 120000 14
> + 125000 12
> + 130000 10
> + 135000 9
> + 140000 8
> + 145000 7
> + 150000 6>;
> + };
> +
> + thermal_sensor2: thermal-sensor-2 {
> + compatible = "generic-adc-thermal";
> + #thermal-sensor-cells = <0>;
> + io-channels = <&auxadc 2>;
> + io-channel-names = "sensor-channel";
> + temperature-lookup-table = <(-25000) 1474
> + (-20000) 1374
> + (-15000) 1260
> + (-10000) 1134
> + (-5000) 1004
> + 0 874
> + 5000 750
> + 10000 635
> + 15000 532
> + 20000 443
> + 25000 367
> + 30000 303
> + 35000 250
> + 40000 206
> + 45000 170
> + 50000 141
> + 55000 117
> + 60000 97
> + 65000 81
> + 70000 68
> + 75000 57
> + 80000 48
> + 85000 41
> + 90000 35
> + 95000 30
> + 100000 25
> + 105000 22
> + 110000 19
> + 115000 16
> + 120000 14
> + 125000 12
> + 130000 10
> + 135000 9
> + 140000 8
> + 145000 7
> + 150000 6>;
> + };
> +};
> +
> +&auxadc {
> + status = "okay";
> +};
> +
> +ð {
> + phy-mode ="rgmii-id";
> + phy-handle = <ðernet_phy0>;
> + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>;
> + snps,reset-delays-us = <0 10000 80000>;
snps,reset-delays-us and snps,reset-gpio are deprecated.
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <ð_default_pins>;
> + pinctrl-1 = <ð_sleep_pins>;
> + status = "okay";
> +
> + mdio {
> + ethernet_phy0: ethernet-phy at 1 {
compatible = "is there any applicable compatible?"
P.S.: if you've got the usual rtl8211f, should be "ethernet-phy-id001c.c916"
reg = <0x1>;
interrupts-extended = <&pio 94 IRQ_TYPE_LEVEL_LOW>;
reset-assert-us = <10000>;
reset-deassert-us = <80000>;
reset-gpios = <&pio 93 GPIO_ACTIVE_HIGH>;
> + reg = <0x1>;
> + interrupts-extended = <&pio 94 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> +&gpu {
> + status = "okay";
> + mali-supply = <&mt6315_7_vbuck1>;
> +};
> +
> +&i2c2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c2_pins>;
> + clock-frequency = <400000>;
> + status = "okay";
Are i2c2,3,4 exposed as pins somewhere? If they are, can you please put a
comment saying so?
This is not mandatory, but IMO it's nice to have as a kind of documentation.
> +};
> +
> +&i2c3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c3_pins>;
> + clock-frequency = <100000>;
> + status = "okay";
> +};
> +
> +&i2c4 {
> + clock-frequency = <100000>;
> + pinctrl-0 = <&i2c4_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +};
> +
> +&i2c6 {
> + clock-frequency = <400000>;
> + pinctrl-0 = <&i2c6_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> +
> + mt6360: pmic at 34 {
> + compatible = "mediatek,mt6360";
> + reg = <0x34>;
> + interrupt-controller;
> + interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
> + interrupt-names = "IRQB";
#interrupt-cells = <1>;
> +
> + charger {
> + compatible = "mediatek,mt6360-chg";
> + richtek,vinovp-microvolt = <14500000>;
> +
> + otg_vbus_regulator: usb-otg-vbus-regulator {
> + regulator-compatible = "usb-otg-vbus";
The regulator-compatible property is deprecated. Please don't use it.
> + regulator-name = "usb-otg-vbus";
> + regulator-min-microvolt = <4425000>;
> + regulator-max-microvolt = <5825000>;
> + };
> + };
> +
> + regulator {
> + compatible = "mediatek,mt6360-regulator";
> + LDO_VIN3-supply = <&mt6360_buck2>;
> +
> + mt6360_buck1: buck1 {
> + regulator-compatible = "BUCK1";
same here and everywhere else.
> + regulator-name = "mt6360,buck1";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP
> + MT6360_OPMODE_ULP>;
> + regulator-always-on;
> + };
> +
> + mt6360_buck2: buck2 {
> + regulator-compatible = "BUCK2";
> + regulator-name = "mt6360,buck2";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP
> + MT6360_OPMODE_ULP>;
> + regulator-always-on;
> + };
> +
> + mt6360_ldo1: ldo1 {
> + regulator-compatible = "LDO1";
> + regulator-name = "mt6360,ldo1";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP>;
> + };
> +
> + mt6360_ldo2: ldo2 {
> + regulator-compatible = "LDO2";
> + regulator-name = "mt6360,ldo2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP>;
> + };
> +
> + mt6360_ldo3: ldo3 {
> + regulator-compatible = "LDO3";
> + regulator-name = "mt6360,ldo3";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP>;
> + };
> +
> + mt6360_ldo5: ldo5 {
> + regulator-compatible = "LDO5";
> + regulator-name = "mt6360,ldo5";
> + regulator-min-microvolt = <2700000>;
> + regulator-max-microvolt = <3600000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP>;
> + };
> +
> + mt6360_ldo6: ldo6 {
> + regulator-compatible = "LDO6";
> + regulator-name = "mt6360,ldo6";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <2100000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP>;
> + };
> +
> + mt6360_ldo7: ldo7 {
> + regulator-compatible = "LDO7";
> + regulator-name = "mt6360,ldo7";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <2100000>;
> + regulator-allowed-modes = <MT6360_OPMODE_NORMAL
> + MT6360_OPMODE_LP>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&mmc0 {
This is not wrong, but can we please keep the ordering consistent between boards?
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&mmc0_default_pins>;
pinctrl-1 = <&mmc0_uhs_pins>;
bus-width = <8>;
max-frequency = <200000000>;
hs400-ds-delay = <0x14c11>;
cap-mmc-highspeed;
cap-mmc-hw-reset;
mmc-hs200-1_8v;
mmc-hs400-1_8v;
no-sdio;
no-sd;
non-removable;
vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
vqmmc-supply = <&mt6359_vufs_ldo_reg>;
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc0_default_pins>;
> + pinctrl-1 = <&mmc0_uhs_pins>;
> + bus-width = <8>;
> + max-frequency = <200000000>;
> + cap-mmc-highspeed;
> + mmc-hs200-1_8v;
> + mmc-hs400-1_8v;
> + cap-mmc-hw-reset;
> + no-sdio;
> + no-sd;
> + hs400-ds-delay = <0x14c11>;
> + vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
> + vqmmc-supply = <&mt6359_vufs_ldo_reg>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&mmc1 {
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc1_default_pins>;
> + pinctrl-1 = <&mmc1_uhs_pins>;
> + cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
> + bus-width = <4>;
> + max-frequency = <200000000>;
> + cap-sd-highspeed;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + vmmc-supply = <&mt6360_ldo5>;
> + vqmmc-supply = <&mt6360_ldo3>;
Does mmc1 support eMMC and SDIO?
If not, no-mmc; no-sdio;
> + status = "okay";
> +};
> +
> +&mt6359_vbbck_ldo_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vcore_buck_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vgpu11_buck_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vproc1_buck_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vproc2_buck_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vpu_buck_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vrf12_ldo_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vsram_md_ldo_reg {
> + regulator-always-on;
> +};
> +
> +&mt6359_vsram_others_ldo_reg {
> + regulator-always-on;
> +};
> +
> +&nor_flash {
> + pinctrl-names = "default";
> + pinctrl-0 = <&nor_pins_default>;
> + status = "okay";
> +
> + flash at 0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <52000000>;
> + spi-rx-bus-width = <2>;
> + spi-tx-bus-width = <2>;
> + };
> +};
> +
> +&pcie0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie0_pins_default>;
> + status = "okay";
> +};
> +
> +&pcie1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie1_pins_default>;
> + status = "okay";
> +};
> +
> +&pciephy {
> + status = "okay";
> +};
> +
> +&pio {
> + eth_default_pins: eth-default-pins {
> + pins-txd {
> + pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>,
> + <PINMUX_GPIO78__FUNC_GBE_TXD2>,
> + <PINMUX_GPIO79__FUNC_GBE_TXD1>,
> + <PINMUX_GPIO80__FUNC_GBE_TXD0>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + };
> +
> + pins-rxd {
> + pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>,
> + <PINMUX_GPIO82__FUNC_GBE_RXD2>,
> + <PINMUX_GPIO83__FUNC_GBE_RXD1>,
> + <PINMUX_GPIO84__FUNC_GBE_RXD0>;
> + };
> +
> + pins-cc {
> + pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>,
> + <PINMUX_GPIO86__FUNC_GBE_RXC>,
> + <PINMUX_GPIO87__FUNC_GBE_RXDV>,
> + <PINMUX_GPIO88__FUNC_GBE_TXEN>;
> + drive-strength = <MTK_DRIVE_8mA>;
s/MTK_DRIVE//g
s/mA//g
drive-strength = <8>;
Please, here and everywhere else, for all values - let's stop using those
MTK_DRIVE_(x)mA definitions, they're just defined as (x), where anyway
the drive-strength property is in milliamps by default.
We don't need these definitions.
> + };
> +
> + pins-mdio {
> + pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>,
> + <PINMUX_GPIO90__FUNC_GBE_MDIO>;
> + input-enable;
> + };
> +
> + pins-power {
> + pinmux = <PINMUX_GPIO91__FUNC_GPIO91>,
> + <PINMUX_GPIO92__FUNC_GPIO92>;
> + output-high;
> + };
> +
> + pins-reset {
> + pinmux = <PINMUX_GPIO93__FUNC_GPIO93>;
> + output-high;
> + };
> +
> + pins-interrupt {
> + pinmux = <PINMUX_GPIO94__FUNC_GPIO94>;
> + input-enable;
> + };
> + };
> +
> + eth_sleep_pins: eth-sleep-pins {
> + pins-txd {
> + pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
> + <PINMUX_GPIO78__FUNC_GPIO78>,
> + <PINMUX_GPIO79__FUNC_GPIO79>,
> + <PINMUX_GPIO80__FUNC_GPIO80>;
> + };
> + pins-cc {
> + pinmux = <PINMUX_GPIO85__FUNC_GPIO85>,
> + <PINMUX_GPIO88__FUNC_GPIO88>,
> + <PINMUX_GPIO87__FUNC_GPIO87>,
> + <PINMUX_GPIO86__FUNC_GPIO86>;
> + };
> + pins-rxd {
> + pinmux = <PINMUX_GPIO81__FUNC_GPIO81>,
> + <PINMUX_GPIO82__FUNC_GPIO82>,
> + <PINMUX_GPIO83__FUNC_GPIO83>,
> + <PINMUX_GPIO84__FUNC_GPIO84>;
> + };
> + pins-mdio {
> + pinmux = <PINMUX_GPIO89__FUNC_GPIO89>,
> + <PINMUX_GPIO90__FUNC_GPIO90>;
> + input-disable;
> + bias-disable;
> + };
> + };
> +
> + gpio_keys_pins: gpio-keys-pins {
> + pins {
> + pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
> + input-enable;
> + };
> + };
> +
> + i2c2_pins: i2c2-default-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO12__FUNC_SDA2>,
> + <PINMUX_GPIO13__FUNC_SCL2>;
> + bias-pull-up;
> + };
> + };
> +
> + i2c3_pins: i2c3-pins {
> + pins {
> + pinmux = <PINMUX_GPIO14__FUNC_SDA3>,
> + <PINMUX_GPIO15__FUNC_SCL3>;
> + bias-pull-up;
> + };
> + };
> +
> + i2c4_pins: i2c4-pins {
> + pins {
> + pinmux = <PINMUX_GPIO16__FUNC_SDA4>,
> + <PINMUX_GPIO17__FUNC_SCL4>;
> + bias-pull-up;
> + };
> + };
> +
> + i2c6_pins: i2c6-pins {
> + pins {
> + pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
> + <PINMUX_GPIO26__FUNC_SCL6>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc0_default_pins: mmc0-default-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_6mA>;
drive-strength = <6>; etc :-)
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
> + <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
> + <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
> + <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
> + <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
> + <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
> + <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
> + <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
> + <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-rst {
> + pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
> + drive-strength = <MTK_DRIVE_6mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + mmc0_uhs_pins: mmc0-uhs-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
> + <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
> + <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
> + <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
> + <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
> + <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
> + <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
> + <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
> + <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-ds {
> + pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-rst {
> + pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + mmc1_default_pins: mmc1-default-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
> + <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-insert {
> + pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
> + bias-pull-up;
> + };
> + };
MMC1 UHS and DEFAULT are exactly the same, you don't need to define those twice.
Here's how we can clean up this block:
mmc1_default_pins: mmc1-default-pins {
pins-clk {
pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
drive-strength = <8>;
};
pins-cmd-dat {
pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
<PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
<PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
<PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
<PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
drive-strength = <8>;
input-enable;
};
};
mmc1_pins_detect: mmc1-detect-pins {
pins-insert {
pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
bias-pull-up;
};
};
&mmc1 {
pinctrl-names = "default", "state_uhs";
pinctrl-0 = <&mmc1_default_pins>, <&mmc1_pins_detect>;
pinctrl-1 = <&mmc1_default_pins>;
....
}
> +
> + mmc1_uhs_pins: mmc1-uhs-pins {
> + pins-clk {
> + pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
> + <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
> + input-enable;
> + drive-strength = <MTK_DRIVE_8mA>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + nor_pins_default: nor-default-pins {
> + pins-ck-io {
> + pinmux = <PINMUX_GPIO142__FUNC_SPINOR_IO0>,
> + <PINMUX_GPIO141__FUNC_SPINOR_CK>,
> + <PINMUX_GPIO143__FUNC_SPINOR_IO1>;
> + drive-strength = <6>;
> + bias-pull-down;
> + };
> +
> + pins-cs {
> + pinmux = <PINMUX_GPIO140__FUNC_SPINOR_CS>;
> + drive-strength = <6>;
> + bias-pull-up;
> + };
> + };
> +
> + pcie0_pins_default: pcie0-default-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO19__FUNC_WAKEN>,
> + <PINMUX_GPIO20__FUNC_PERSTN>,
> + <PINMUX_GPIO21__FUNC_CLKREQN>;
> + bias-pull-up;
> + };
> + };
> +
> + pcie1_pins_default: pcie1-default-pins {
> + pins-bus {
> + pinmux = <PINMUX_GPIO0__FUNC_PERSTN_1>,
> + <PINMUX_GPIO1__FUNC_CLKREQN_1>,
> + <PINMUX_GPIO2__FUNC_WAKEN_1>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> + };
> +
> + led_pins: led-pins {
> + pins-power-en {
> + pinmux = <PINMUX_GPIO107__FUNC_GPIO107>;
> + output-high;
> + };
> + };
> +
> + spi0_pins: spi0-default-pins {
> + pins-cs-mosi-clk {
> + pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>,
> + <PINMUX_GPIO134__FUNC_SPIM0_MO>,
> + <PINMUX_GPIO133__FUNC_SPIM0_CLK>;
> + bias-disable;
> + };
> +
> + pins-miso {
> + pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>;
> + bias-pull-down;
> + };
> + };
> +
> + spi1_pins: spi1-default-pins {
> + pins-cs-mosi-clk {
> + pinmux = <PINMUX_GPIO136__FUNC_SPIM1_CSB>,
> + <PINMUX_GPIO138__FUNC_SPIM1_MO>,
> + <PINMUX_GPIO137__FUNC_SPIM1_CLK>;
> + bias-disable;
> + };
> +
> + pins-miso {
> + pinmux = <PINMUX_GPIO139__FUNC_SPIM1_MI>;
> + bias-pull-down;
> + };
> + };
> +
> + uart0_pins: uart0-pins {
> + pins_rx {
No underscores, please.
> + pinmux = <PINMUX_GPIO99__FUNC_URXD0>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins_tx {
> + pinmux = <PINMUX_GPIO98__FUNC_UTXD0>;
> + };
> + };
> +
> + uart1_pins: uart1-pins {
> + pins_rx {
> + pinmux = <PINMUX_GPIO103__FUNC_URXD1>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins_tx {
> + pinmux = <PINMUX_GPIO102__FUNC_UTXD1>;
> + };
> +
> + pins_rts {
> + pinmux = <PINMUX_GPIO100__FUNC_URTS1>;
> + output-enable;
Are you really sure that you need output-enable here?!
RTS is not an output buffer....
I don't think you do. Please double check.
> + };
> +
> + pins_cts {
> + pinmux = <PINMUX_GPIO101__FUNC_UCTS1>;
> + input-enable;
> + };
> + };
> +
> + uart2_pins: uart2-pins {
> + pins_rx {
> + pinmux = <PINMUX_GPIO68__FUNC_URXD2>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins_tx {
> + pinmux = <PINMUX_GPIO67__FUNC_UTXD2>;
> + };
> +
> + pins_rts {
> + pinmux = <PINMUX_GPIO66__FUNC_URTS2>;
> + output-enable;
> + };
> +
> + pins_cts {
> + pinmux = <PINMUX_GPIO65__FUNC_UCTS2>;
> + input-enable;
> + };
> + };
> +
> + uart3_pins: uart3-pins {
> + pins_rx {
> + pinmux = <PINMUX_GPIO5__FUNC_URXD3>;
> + input-enable;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins_tx {
> + pinmux = <PINMUX_GPIO4__FUNC_UTXD3>;
> + };
> + };
> +
> + uart4_pins: uart4-pins {
> + pins_rx {
> + pinmux = <PINMUX_GPIO7__FUNC_URXD4>;
> + input-enable;
> + bias-pull-up;
> + };
> +
> + pins_tx {
> + pinmux = <PINMUX_GPIO6__FUNC_UTXD4>;
> + };
> + };
> +};
> +
> +&pmic {
> + interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
> +};
> +
> +&scp {
> + memory-region = <&scp_mem>;
> + status = "okay";
> +};
> +
> +&spmi {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + mt6315 at 6 {
> + compatible = "mediatek,mt6315-regulator";
> + reg = <0x6 SPMI_USID>;
> +
> + regulators {
> + mt6315_6_vbuck1: vbuck1 {
> + regulator-compatible = "vbuck1";
We should check if we can avoid using regulator-compatible on mt6315 as well...
I honestly never checked if this is possible, but I think it is.
Eventually, if you can check and verify that it's not needed, we should even
remove that from all devicetrees, but that's not entirely relevant for this
patch anyway.
I'm just saying my plans out loud :-)
> + regulator-name = "Vbcpu";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1193750>;
> + regulator-enable-ramp-delay = <256>;
> + regulator-ramp-delay = <6250>;
> + regulator-allowed-modes = <0 1 2>;
> + regulator-always-on;
> + };
> + };
> + };
> +
> + mt6315 at 7 {
> + compatible = "mediatek,mt6315-regulator";
> + reg = <0x7 SPMI_USID>;
> +
> + regulators {
> + mt6315_7_vbuck1: vbuck1 {
> + regulator-compatible = "vbuck1";
> + regulator-name = "Vgpu";
> + regulator-min-microvolt = <625000>;
> + regulator-max-microvolt = <1193750>;
> + regulator-enable-ramp-delay = <256>;
> + regulator-ramp-delay = <6250>;
> + regulator-allowed-modes = <0 1 2>;
> + regulator-always-on;
> + };
> + };
> + };
> +};
> +
> +&spi0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi0_pins>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> +
> + tpm: tpm at 0 {
> + compatible = "infineon,slb9670";
> + reg = <0>;
> + spi-max-frequency = <18500000>;
> + };
> +};
> +
> +&spi1 {
Same as before, is this exposed somewhere? If it is, can we please get a comment in
here advertising so?
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi1_pins>;
> + mediatek,pad-select = <0>;
> + status = "okay";
> +};
> +
> +&thermal_zones {
> + board0-thermal {
"board0" is a bit generic, is that on purpose?
If this is a fixed placement sensor, you could name this something like
pcb-bottom-thermal pcb-left-thermal skin-thermal board-soc-thermal
etc etc etc :-)
> + polling-delay = <1000>; /* milliseconds */
> + polling-delay-passive = <0>; /* milliseconds */
> + thermal-sensors = <&thermal_sensor0>;
> +
> + trips {
> + trip-alert {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + trip-crit {
> + temperature = <95000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + board1-thermal {
> + polling-delay = <1000>; /* milliseconds */
> + polling-delay-passive = <0>; /* milliseconds */
> + thermal-sensors = <&thermal_sensor1>;
> +
> + trips {
> + trip-alert {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + trip-crit {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> +
> + board2-thermal {
> + polling-delay = <1000>; /* milliseconds */
> + polling-delay-passive = <0>; /* milliseconds */
> + thermal-sensors = <&thermal_sensor2>;
> +
> + trips {
> + trip-alert {
> + temperature = <75000>;
> + hysteresis = <2000>;
> + type = "passive";
> + };
> +
> + trip-crit {
> + temperature = <85000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> + };
> +};
> +
> +&uart0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart0_pins>;
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart1_pins>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart2_pins>;
> + uart-has-rtscts;
> + status = "okay";
> +};
> +
> +&uart3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart3_pins>;
> + status = "okay";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_pins>;
> + status = "okay";
> +};
> +
> +/* USB3 */
> +&u3phy0 {
> + status = "okay";
> +};
> +
> +/* PCIe1/USB2 */
> +&u3phy1 {
> + status = "okay";
> +};
> +
> +/* USB2 */
> +&u3phy2 {
> + status = "okay";
> +};
> +
> +/* USB2 */
> +&u3phy3 {
> + status = "okay";
> +};
> +
> +/* USB3 front port */
> +&xhci0 {
It's not gonna work like this. I recently fixed the USB nodes in MT8195 by adding
MTU3 where necessary...
Check mt8195.dtsi - only one XHCI controller isn't placed behind MTU3, and that is
XHCI1 (11290000), while the others are MTU3.
As far as I can see from this DT, it should now instead look like..
&ssusb0 {
dr_mode = "host";
vusb33-supply = <&mt6359_vusb_ldo_reg>;
status = "okay";
};
&ssusb2 {
dr_mode = "host";
vusb33-supply = <&mt6359_vusb_ldo_reg>;
status = "okay";
};
&ssusb3 {
dr_mode = "host";
vusb33-supply = <&mt6359_vusb_ldo_reg>;
status = "okay";
};
&xhci0 {
vbus-supply = <&otg_vbus_regulator>;
status = "okay";
};
&xhci1 {
vusb33-supply = <&mt6359_vusb_ldo_reg>;
vbus is always supplied by something, as otherwise USB won't work - whether this
is an always-on regulator or a passthrough from external supply this doesn't really
matter - you should model a regulator-fixed that provides the 5V VBUS line.
For example:
vbus_fixed: regulator-vbus {
compatible = "regulator-fixed";
regulator-name = "usb-vbus";
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
P.S.: If the rail has a different name, please use that different name. Obviously
that requires you to have schematics at hand, and I don't know if you do: if you
don't, then that regulator-vbus name is just fine.
vbus-supply = <&vbus_fixed>;
mediatek,u3p-dis-msk = <0x1>;
status = "okay";
};
&xhci2 {
vbus-supply = <&vbus_fixed>;
status = "okay";
};
&xhci3 {
vbus-supply = <&vbus_fixed>;
status = "okay";
};
Cheers,
Angelo
> + vusb33-supply = <&mt6359_vusb_ldo_reg>;
> + vbus-supply = <&otg_vbus_regulator>;
> + status = "okay";
> +};
> +
> +/* USB2 M.2 Key-B */
> +&xhci1 {
> + vusb33-supply = <&mt6359_vusb_ldo_reg>;
> + mediatek,u3p-dis-msk = <0x01>;
> + status = "okay";
> +};
> +
> +/* USB2 M.2 Key-E */
> +&xhci2 {
> + vusb33-supply = <&mt6359_vusb_ldo_reg>;
> + status = "okay";
> +};
> +
> +/* USB2 to on-board usb hub */
> +&xhci3 {
> + vusb33-supply = <&mt6359_vusb_ldo_reg>;
> + status = "okay";
> +};
More information about the Linux-mediatek
mailing list