[PATCH v4 3/5] media: platform: mediatek: isp_30: add mediatek ISP3.0 sensor interface
Sakari Ailus
sakari.ailus at iki.fi
Thu Feb 15 01:21:01 PST 2024
Hi Julien,
Thanks for the patch.
On Wed, Jan 10, 2024 at 03:14:40PM +0100, Julien Stephan wrote:
> From: Louis Kuo <louis.kuo at mediatek.com>
>
> This will add the mediatek ISP3.0 seninf (sensor interface) driver found
> on several Mediatek SoCs such as the mt8365.
>
> Then seninf module has 4 physical CSI-2 inputs. Depending on the soc they
> may not be all connected.
>
> Signed-off-by: Louis Kuo <louis.kuo at mediatek.com>
> Signed-off-by: Phi-bang Nguyen <pnguyen at baylibre.com>
> Signed-off-by: Florian Sylvestre <fsylvestre at baylibre.com>
> Co-developed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> Signed-off-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
> Co-developed-by: Julien Stephan <jstephan at baylibre.com>
> Signed-off-by: Julien Stephan <jstephan at baylibre.com>
> ---
> MAINTAINERS | 1 +
> drivers/media/platform/mediatek/Kconfig | 1 +
> drivers/media/platform/mediatek/Makefile | 1 +
> drivers/media/platform/mediatek/isp/Kconfig | 2 +
> drivers/media/platform/mediatek/isp/Makefile | 3 +
> .../platform/mediatek/isp/isp_30/Kconfig | 16 +
> .../platform/mediatek/isp/isp_30/Makefile | 3 +
> .../mediatek/isp/isp_30/seninf/Makefile | 5 +
> .../mediatek/isp/isp_30/seninf/mtk_seninf.c | 1488 +++++++++++++++++
> .../isp/isp_30/seninf/mtk_seninf_reg.h | 112 ++
> 10 files changed, 1632 insertions(+)
> create mode 100644 drivers/media/platform/mediatek/isp/Kconfig
> create mode 100644 drivers/media/platform/mediatek/isp/Makefile
> create mode 100644 drivers/media/platform/mediatek/isp/isp_30/Kconfig
> create mode 100644 drivers/media/platform/mediatek/isp/isp_30/Makefile
> create mode 100644 drivers/media/platform/mediatek/isp/isp_30/seninf/Makefile
> create mode 100644 drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf.c
> create mode 100644 drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf_reg.h
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 3ea2158864e1..52d200d5e36c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13618,6 +13618,7 @@ M: Andy Hsieh <andy.hsieh at mediatek.com>
> S: Supported
> F: Documentation/devicetree/bindings/media/mediatek,mt8365-camsv.yaml
> F: Documentation/devicetree/bindings/media/mediatek,mt8365-seninf.yaml
> +F: drivers/media/platform/mediatek/isp/isp_30/seninf/*
>
> MEDIATEK SMI DRIVER
> M: Yong Wu <yong.wu at mediatek.com>
> diff --git a/drivers/media/platform/mediatek/Kconfig b/drivers/media/platform/mediatek/Kconfig
> index 84104e2cd024..4e0a5a43f35e 100644
> --- a/drivers/media/platform/mediatek/Kconfig
> +++ b/drivers/media/platform/mediatek/Kconfig
> @@ -7,3 +7,4 @@ source "drivers/media/platform/mediatek/mdp/Kconfig"
> source "drivers/media/platform/mediatek/vcodec/Kconfig"
> source "drivers/media/platform/mediatek/vpu/Kconfig"
> source "drivers/media/platform/mediatek/mdp3/Kconfig"
> +source "drivers/media/platform/mediatek/isp/Kconfig"
> diff --git a/drivers/media/platform/mediatek/Makefile b/drivers/media/platform/mediatek/Makefile
> index 38e6ba917fe5..695f05f525a6 100644
> --- a/drivers/media/platform/mediatek/Makefile
> +++ b/drivers/media/platform/mediatek/Makefile
> @@ -4,3 +4,4 @@ obj-y += mdp/
> obj-y += vcodec/
> obj-y += vpu/
> obj-y += mdp3/
> +obj-y += isp/
> diff --git a/drivers/media/platform/mediatek/isp/Kconfig b/drivers/media/platform/mediatek/isp/Kconfig
> new file mode 100644
> index 000000000000..708b9a6660d2
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/Kconfig
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +source "drivers/media/platform/mediatek/isp/isp_30/Kconfig"
> diff --git a/drivers/media/platform/mediatek/isp/Makefile b/drivers/media/platform/mediatek/isp/Makefile
> new file mode 100644
> index 000000000000..a81ab33d0dd3
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/Makefile
> @@ -0,0 +1,3 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +
> +obj-y += isp_30/
> diff --git a/drivers/media/platform/mediatek/isp/isp_30/Kconfig b/drivers/media/platform/mediatek/isp/isp_30/Kconfig
> new file mode 100644
> index 000000000000..9791312589fb
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/isp_30/Kconfig
> @@ -0,0 +1,16 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +config MTK_SENINF30
> + tristate "MediaTek ISP3.0 SENINF driver"
> + depends on VIDEO_V4L2_SUBDEV_API
> + depends on MEDIA_CAMERA_SUPPORT
> + depends on ARCH_MEDIATEK || COMPILE_TEST
> + depends on OF
> + select V4L2_FWNODE
> + default n
> + help
> + This driver provides a MIPI CSI-2 receiver interface to connect
> + an external camera module with MediaTek ISP3.0. It is able to handle
> + multiple cameras at the same time.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called mtk-seninf.
> diff --git a/drivers/media/platform/mediatek/isp/isp_30/Makefile b/drivers/media/platform/mediatek/isp/isp_30/Makefile
> new file mode 100644
> index 000000000000..ac3142de4739
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/isp_30/Makefile
> @@ -0,0 +1,3 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +obj-$(CONFIG_MTK_SENINF30) += seninf/
> diff --git a/drivers/media/platform/mediatek/isp/isp_30/seninf/Makefile b/drivers/media/platform/mediatek/isp/isp_30/seninf/Makefile
> new file mode 100644
> index 000000000000..f28480d6d6c3
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/isp_30/seninf/Makefile
> @@ -0,0 +1,5 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +mtk-seninf-objs += mtk_seninf.o
> +
> +obj-$(CONFIG_MTK_SENINF30) += mtk-seninf.o
> diff --git a/drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf.c b/drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf.c
> new file mode 100644
> index 000000000000..67b2c697d9ca
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf.c
> @@ -0,0 +1,1488 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2022 MediaTek Inc.
> + */
> +#include <linux/bitfield.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/module.h>
> +#include <linux/of_graph.h>
> +#include <linux/of_platform.h>
> +#include <linux/phy/phy.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/videodev2.h>
> +#include <media/media-device.h>
> +#include <media/media-entity.h>
> +#include <media/v4l2-async.h>
> +#include <media/v4l2-common.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-dev.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-event.h>
> +#include <media/v4l2-fwnode.h>
> +#include <media/v4l2-mc.h>
> +#include <media/v4l2-subdev.h>
> +
> +#include "mtk_seninf_reg.h"
> +
> +#define SENINF_TIMESTAMP_STEP 0x67
> +#define SENINF_SETTLE_DELAY 0x15
> +#define SENINF_HS_TRAIL_PARAMETER 0x8
> +
> +#define SENINF_MAX_NUM_INPUTS 4
> +#define SENINF_MAX_NUM_OUTPUTS 6
> +#define SENINF_MAX_NUM_MUXES 6
> +#define SENINF_MAX_NUM_PADS (SENINF_MAX_NUM_INPUTS + \
> + SENINF_MAX_NUM_OUTPUTS)
> +
> +#define SENINF_DEFAULT_BUS_FMT MEDIA_BUS_FMT_SGRBG10_1X10
> +#define SENINF_DEFAULT_WIDTH 1920
> +#define SENINF_DEFAULT_HEIGHT 1080
> +
> +#define SENINF_PAD_10BIT 0
> +
> +#define SENINF_TEST_MODEL 0
> +#define SENINF_NORMAL_MODEL 1
> +#define SENINF_ALL_ERR_IRQ_EN 0x7f
> +#define SENINF_IRQ_CLR_SEL 0x80000000
> +
> +#define SENINF_MIPI_SENSOR 0x8
> +
> +#define MTK_CSI_MAX_LANES 4
> +
> +/* Port number in the device tree. */
> +enum mtk_seninf_port {
> + CSI_PORT_0 = 0, /* 4D1C or 2D1C */
> + CSI_PORT_1, /* 4D1C */
> + CSI_PORT_2, /* 4D1C */
> + CSI_PORT_0B, /* 2D1C */
> +};
> +
> +enum mtk_seninf_id {
> + SENINF_1 = 0,
> + SENINF_2 = 1,
> + SENINF_3 = 2,
> + SENINF_5 = 4,
> +};
> +
> +static const u32 port_to_seninf_id[] = {
> + [CSI_PORT_0] = SENINF_1,
> + [CSI_PORT_1] = SENINF_3,
> + [CSI_PORT_2] = SENINF_5,
> + [CSI_PORT_0B] = SENINF_2,
> +};
> +
> +enum mtk_seninf_phy_mode {
> + SENINF_PHY_MODE_NONE,
> + SENINF_PHY_MODE_4D1C,
> + SENINF_PHY_MODE_2D1C,
> +};
> +
> +enum mtk_seninf_format_flag {
> + MTK_SENINF_FORMAT_BAYER = BIT(0),
> + MTK_SENINF_FORMAT_DPCM = BIT(1),
> + MTK_SENINF_FORMAT_JPEG = BIT(2),
> + MTK_SENINF_FORMAT_INPUT_ONLY = BIT(3),
> +};
> +
> +/**
> + * struct mtk_seninf_conf - Model-specific SENINF parameters
> + * @model: Model description
> + * @nb_inputs: Number of SENINF inputs
> + * @nb_muxes: Number of SENINF MUX (FIFO) instances
> + * @nb_outputs: Number of outputs (to CAM and CAMSV instances)
> + */
> +struct mtk_seninf_conf {
> + const char *model;
> + u8 nb_inputs;
> + u8 nb_muxes;
> + u8 nb_outputs;
> +};
> +
> +/**
> + * struct mtk_seninf_format_info - Information about media bus formats
> + * @code: V4L2 media bus code
> + * @flags: Flags describing the format, as a combination of MTK_SENINF_FORMAT_*
> + */
> +struct mtk_seninf_format_info {
> + u32 code;
> + u32 flags;
> +};
> +
> +/**
> + * struct mtk_seninf_input - SENINF input block
> + * @pad: DT port and media entity pad number
> + * @seninf_id: SENINF hardware instance ID
> + * @base: Memory mapped I/O based address
> + * @seninf: Back pointer to the mtk_seninf
> + * @phy: PHY connected to the input
> + * @phy_mode: PHY operation mode (NONE when the input is not connected)
> + * @bus: CSI-2 bus configuration from DT
> + * @source_sd: Source subdev connected to the input
> + */
> +struct mtk_seninf_input {
> + enum mtk_seninf_port pad;
> + enum mtk_seninf_id seninf_id;
> + void __iomem *base;
> + struct mtk_seninf *seninf;
> +
> + struct phy *phy;
> + enum mtk_seninf_phy_mode phy_mode;
> +
> + struct v4l2_mbus_config_mipi_csi2 bus;
> +
> + struct v4l2_subdev *source_sd;
> +};
> +
> +/**
> + * struct mtk_seninf_mux - SENINF MUX channel
> + * @pad: DT port and media entity pad number
> + * @mux_id: MUX hardware instance ID
> + * @base: Memory mapped I/O based address
> + * @seninf: Back pointer to the mtk_seninf
> + */
> +struct mtk_seninf_mux {
> + unsigned int pad;
> + unsigned int mux_id;
> + void __iomem *base;
> + struct mtk_seninf *seninf;
> +};
> +
> +/**
> + * struct mtk_seninf - Top-level SENINF device
> + * @dev: The (platform) device
> + * @phy: PHYs at the SENINF inputs
> + * @num_clks: Number of clocks in the clks array
> + * @clks: Clocks
> + * @base: Memory mapped I/O base address
> + * @media_dev: Media controller device
> + * @v4l2_dev: V4L2 device
> + * @subdev: V4L2 subdevice
> + * @pads: Media entity pads
> + * @notifier: V4L2 async notifier for source subdevs
> + * @ctrl_handler: V4L2 controls handler
> + * @source_format: Active format on the source pad
> + * @inputs: Array of SENINF inputs
> + * @muxes: Array of MUXes
> + * @conf: Model-specific SENINF parameters
> + * @is_testmode: Whether or not the test pattern generator is enabled
> + */
> +struct mtk_seninf {
> + struct device *dev;
> + struct phy *phy[5];
> + unsigned int num_clks;
> + struct clk_bulk_data *clks;
> + void __iomem *base;
> +
> + struct media_device media_dev;
> + struct v4l2_device v4l2_dev;
> + struct v4l2_subdev subdev;
> + struct media_pad pads[SENINF_MAX_NUM_PADS];
> + struct v4l2_async_notifier notifier;
> + struct v4l2_ctrl_handler ctrl_handler;
> +
> + struct mtk_seninf_input inputs[SENINF_MAX_NUM_INPUTS];
> + struct mtk_seninf_mux muxes[SENINF_MAX_NUM_MUXES];
> +
> + const struct mtk_seninf_conf *conf;
> +
> + bool is_testmode;
> +};
> +
> +inline struct mtk_seninf *sd_to_mtk_seninf(struct v4l2_subdev *sd)
> +{
> + return container_of(sd, struct mtk_seninf, subdev);
> +}
> +
> +static inline bool mtk_seninf_pad_is_sink(struct mtk_seninf *priv,
> + unsigned int pad)
> +{
> + return pad < priv->conf->nb_inputs;
It'd be a bit cleaner to test pad flags instead.
> +}
> +
> +static inline bool mtk_seninf_pad_is_source(struct mtk_seninf *priv,
> + unsigned int pad)
> +{
> + return !mtk_seninf_pad_is_sink(priv, pad);
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * Formats
> + */
> +
> +static const struct mtk_seninf_format_info mtk_seninf_formats[] = {
> + {
> + .code = MEDIA_BUS_FMT_SBGGR8_1X8,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGBRG8_1X8,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGRBG8_1X8,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SRGGB8_1X8,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGRBG10_1X10,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SRGGB10_1X10,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SBGGR10_1X10,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGBRG10_1X10,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SBGGR12_1X12,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGBRG12_1X12,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGRBG12_1X12,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SRGGB12_1X12,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SBGGR14_1X14,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGBRG14_1X14,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGRBG14_1X14,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SRGGB14_1X14,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SBGGR16_1X16,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGBRG16_1X16,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SGRBG16_1X16,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_SRGGB16_1X16,
> + .flags = MTK_SENINF_FORMAT_BAYER,
> + }, {
> + .code = MEDIA_BUS_FMT_UYVY8_1X16,
> + }, {
> + .code = MEDIA_BUS_FMT_VYUY8_1X16,
> + }, {
> + .code = MEDIA_BUS_FMT_YUYV8_1X16,
> + }, {
> + .code = MEDIA_BUS_FMT_YVYU8_1X16,
> + }, {
> + .code = MEDIA_BUS_FMT_JPEG_1X8,
> + .flags = MTK_SENINF_FORMAT_JPEG,
> + }, {
> + .code = MEDIA_BUS_FMT_S5C_UYVY_JPEG_1X8,
> + .flags = MTK_SENINF_FORMAT_JPEG,
> + },
> + /* Keep the input-only formats last. */
> + {
> + .code = MEDIA_BUS_FMT_SGRBG10_DPCM8_1X8,
> + .flags = MTK_SENINF_FORMAT_DPCM | MTK_SENINF_FORMAT_INPUT_ONLY,
> + }, {
> + .code = MEDIA_BUS_FMT_SRGGB10_DPCM8_1X8,
> + .flags = MTK_SENINF_FORMAT_DPCM | MTK_SENINF_FORMAT_INPUT_ONLY,
> + }, {
> + .code = MEDIA_BUS_FMT_SBGGR10_DPCM8_1X8,
> + .flags = MTK_SENINF_FORMAT_DPCM | MTK_SENINF_FORMAT_INPUT_ONLY,
> + }, {
> + .code = MEDIA_BUS_FMT_SGBRG10_DPCM8_1X8,
> + .flags = MTK_SENINF_FORMAT_DPCM | MTK_SENINF_FORMAT_INPUT_ONLY,
> + }
> +};
> +
> +static const struct mtk_seninf_format_info *mtk_seninf_format_info(u32 code)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < ARRAY_SIZE(mtk_seninf_formats); ++i) {
> + if (mtk_seninf_formats[i].code == code)
> + return &mtk_seninf_formats[i];
> + }
> +
> + return NULL;
> +}
> +
> +static void __mtk_seninf_update(struct mtk_seninf *priv, u32 reg,
> + u32 mask, u32 value)
> +{
> + u32 val = readl(priv->base + reg);
> +
> + writel((val & ~mask) | (value & mask), priv->base + reg);
> +}
> +
> +#define mtk_seninf_update(priv, reg, field, val) \
> + __mtk_seninf_update(priv, reg, reg##_##field, \
Please align the backslashes.
> + FIELD_PREP(reg##_##field, val))
> +
> +static void __mtk_seninf_input_update(struct mtk_seninf_input *input, u32 reg,
> + u32 mask, u32 value)
> +{
> + u32 val = readl(input->base + reg);
> +
> + writel((val & ~mask) | (value & mask), input->base + reg);
> +}
> +
> +#define mtk_seninf_input_update(input, reg, field, val) \
> + __mtk_seninf_input_update(input, reg, reg##_##field, \
> + FIELD_PREP(reg##_##field, val))
> +
> +static u32 mtk_seninf_mux_read(struct mtk_seninf_mux *mux, u32 reg)
> +{
> + return readl(mux->base + reg);
> +}
> +
> +static void mtk_seninf_mux_write(struct mtk_seninf_mux *mux, u32 reg,
> + u32 value)
> +{
> + writel(value, mux->base + reg);
> +}
> +
> +static void __mtk_seninf_mux_update(struct mtk_seninf_mux *mux, u32 reg,
> + u32 mask, u32 value)
> +{
> + u32 val = mtk_seninf_mux_read(mux, reg);
> +
> + mtk_seninf_mux_write(mux, reg, (val & ~mask) | (value & mask));
> +}
> +
> +#define mtk_seninf_mux_update(mux, reg, field, val) \
> + __mtk_seninf_mux_update(mux, reg, reg##_##field, \
> + FIELD_PREP(reg##_##field, val))
> +
> +/* -----------------------------------------------------------------------------
> + * Hardware Configuration
> + *
> + * The SENINF is the camera sensor interface. On the input side it contains
> + * input channels (also named SENINF), each made of a CSI-2 receiver, an
> + * interface for parallel sensors, and a test pattern generator. The inputs are
> + * routed through a N:M crossbar switch (TOP MUX) to VC/DT filters with a FIFO
> + * (MUX). The MUX are routed to another N:M crossbar switch (CAM MUX), whose
> + * output is then connected to other IP cores.
> + *
> + * +-------------------------------------------------------+
> + * | SENINF |
> + * | |
> + * +-------+ | +----------+ TOP MUX |
> + * | | | | SENINF | |\ CAM MUX |
> + * | D-PHY | ---> | CSI-2 RX | ---> | | +------------+ |\ |
> + * | | | | TPG | -> | | ---> | MUX (FIFO) | ---> | | ---> CAMSV
> + * +-------+ | +----------+ -> | | +------------+ -> | | |
> + * | |/ -> | | |
> + * | |/ |
> + * | |
> + * ... | ... ... --->
> + * | |
> + * | |
> + * +-------------------------------------------------------+
> + *
> + * The number of PHYs, SENINF and MUX differ between SoCs. MT8167 has a single
> + * MUX and thus no output CAM MUX crossbar switch.
> + */
> +
> +static void mtk_seninf_csi2_setup_phy(struct mtk_seninf *priv)
> +{
> + /* CSI0 */
> + if (priv->inputs[CSI_PORT_0].phy) {
> + struct mtk_seninf_input *input = &priv->inputs[CSI_PORT_0];
> +
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI0,
> + DPHY_MODE, 0 /* 4D1C*/);
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI0,
> + CK_SEL_1, input->bus.clock_lane);
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI0,
> + CK_SEL_2, 2);
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI0,
> + PHY_SENINF_LANE_MUX_CSI0_EN, 1);
> + }
> +
> + /* CSI1 */
> + if (priv->inputs[CSI_PORT_1].phy) {
> + struct mtk_seninf_input *input = &priv->inputs[CSI_PORT_1];
> +
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI1,
> + DPHY_MODE, 0 /* 4D1C */);
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI1,
> + CK_SEL_1, input->bus.clock_lane);
> + mtk_seninf_update(priv, SENINF_TOP_PHY_SENINF_CTL_CSI1,
> + PHY_SENINF_LANE_MUX_CSI1_EN, 1);
> + }
> +}
> +
> +static void mtk_seninf_input_setup_csi2_rx(struct mtk_seninf_input *input)
> +{
> + unsigned int lanes[MTK_CSI_MAX_LANES] = { };
> + unsigned int i;
> +
> + /*
> + * Configure data lane muxing. In 2D1C mode, lanes 0 to 2 correspond to
> + * CSIx[AB]_L{0,1,2}, and in 4D1C lanes 0 to 5 correspond to
> + * CSIxA_L{0,1,2}, CSIxB_L{0,1,2}.
> + *
> + * The clock lane must be skipped when calculating the index of the
> + * physical data lane. For instance, in 4D1C mode, the sensor clock
> + * lane is typically connected to lane 2 (CSIxA_L2), and the sensor
> + * data lanes 0-3 to lanes 1 (CSIxA_L1), 3 (CSIxB_L0), 0 (CSIxA_L0) and
> + * 4 (CSIxB_L1). The when skipping the clock lane, the data lane
> + * indices become 1, 2, 0 and 3.
> + */
> + for (i = 0; i < input->bus.num_data_lanes; ++i) {
> + lanes[i] = input->bus.data_lanes[i];
> + if (lanes[i] > input->bus.clock_lane)
> + lanes[i]--;
> + }
> +
> + mtk_seninf_input_update(input, MIPI_RX_CON24_CSI0, CSI0_BIST_LN0_MUX, lanes[0]);
> + mtk_seninf_input_update(input, MIPI_RX_CON24_CSI0, CSI0_BIST_LN1_MUX, lanes[1]);
> + mtk_seninf_input_update(input, MIPI_RX_CON24_CSI0, CSI0_BIST_LN2_MUX, lanes[2]);
> + mtk_seninf_input_update(input, MIPI_RX_CON24_CSI0, CSI0_BIST_LN3_MUX, lanes[3]);
> +}
> +
> +static void mtk_seninf_input_setup_csi2(struct mtk_seninf_input *input,
> + struct v4l2_subdev_state *state)
> +{
> + const struct mtk_seninf_format_info *fmtinfo;
> + const struct v4l2_mbus_framefmt *format;
> + unsigned int num_data_lanes = input->bus.num_data_lanes;
> + unsigned int val = 0;
u32?
> +
> + format = v4l2_subdev_state_get_stream_format(state, input->pad, 0);
> + fmtinfo = mtk_seninf_format_info(format->code);
> +
> + /* Configure timestamp */
> + writel(SENINF_TIMESTAMP_STEP, input->base + SENINF_TG1_TM_STP);
> +
> + /* HQ */
> + writel(0x0, input->base + SENINF_TG1_PH_CNT);
> + writel(0x10001, input->base + SENINF_TG1_SEN_CK);
> +
> + /* First Enable Sensor interface and select pad (0x1a04_0200) */
> + mtk_seninf_input_update(input, SENINF_CTRL, SENINF_EN, 1);
> + mtk_seninf_input_update(input, SENINF_CTRL, PAD2CAM_DATA_SEL, SENINF_PAD_10BIT);
> + mtk_seninf_input_update(input, SENINF_CTRL, SENINF_SRC_SEL, 0);
> + mtk_seninf_input_update(input, SENINF_CTRL_EXT, SENINF_CSI2_IP_EN, 1);
> + mtk_seninf_input_update(input, SENINF_CTRL_EXT, SENINF_NCSI2_IP_EN, 0);
> +
> + /* DPCM Enable */
> + if (fmtinfo->flags & MTK_SENINF_FORMAT_DPCM)
> + val = SENINF_CSI2_DPCM_DI_2A_DPCM_EN;
> + else
> + val = SENINF_CSI2_DPCM_DI_30_DPCM_EN;
> + writel(val, input->base + SENINF_CSI2_DPCM);
> +
> + /* Settle delay */
> + mtk_seninf_input_update(input, SENINF_CSI2_LNRD_TIMING,
> + DATA_SETTLE_PARAMETER, SENINF_SETTLE_DELAY);
> +
> + /* HQ */
> + writel(0x10, input->base + SENINF_CSI2_LNRC_FSM);
> +
> + /* CSI2 control */
> + val = readl(input->base + SENINF_CSI2_CTL)
> + | (FIELD_PREP(SENINF_CSI2_CTL_ED_SEL, DATA_HEADER_ORDER_DI_WCL_WCH)
> + | SENINF_CSI2_CTL_CLOCK_LANE_EN | (BIT(num_data_lanes) - 1));
These two lines should be aligned right of "= ", not at it.
> + writel(val, input->base + SENINF_CSI2_CTL);
> +
> + mtk_seninf_input_update(input, SENINF_CSI2_RESYNC_MERGE_CTL,
> + BYPASS_LANE_RESYNC, 0);
> + mtk_seninf_input_update(input, SENINF_CSI2_RESYNC_MERGE_CTL, CDPHY_SEL, 0);
> + mtk_seninf_input_update(input, SENINF_CSI2_RESYNC_MERGE_CTL,
> + CPHY_LANE_RESYNC_CNT, 3);
> + mtk_seninf_input_update(input, SENINF_CSI2_MODE, CSR_CSI2_MODE, 0);
> + mtk_seninf_input_update(input, SENINF_CSI2_MODE, CSR_CSI2_HEADER_LEN, 0);
> + mtk_seninf_input_update(input, SENINF_CSI2_DPHY_SYNC, SYNC_SEQ_MASK_0, 0xff00);
> + mtk_seninf_input_update(input, SENINF_CSI2_DPHY_SYNC, SYNC_SEQ_PAT_0, 0x001d);
> +
> + mtk_seninf_input_update(input, SENINF_CSI2_CTL, CLOCK_HS_OPTION, 0);
> + mtk_seninf_input_update(input, SENINF_CSI2_CTL, HSRX_DET_EN, 0);
> + mtk_seninf_input_update(input, SENINF_CSI2_CTL, HS_TRAIL_EN, 1);
> + mtk_seninf_input_update(input, SENINF_CSI2_HS_TRAIL, HS_TRAIL_PARAMETER,
> + SENINF_HS_TRAIL_PARAMETER);
> +
> + /* Set debug port to output packet number */
> + mtk_seninf_input_update(input, SENINF_CSI2_DGB_SEL, DEBUG_EN, 1);
> + mtk_seninf_input_update(input, SENINF_CSI2_DGB_SEL, DEBUG_SEL, 0x1a);
> +
> + /* HQ */
> + writel(0xfffffffe, input->base + SENINF_CSI2_SPARE0);
> +
> + /* Enable CSI2 IRQ mask */
> + /* Turn on all interrupt */
> + writel(0xffffffff, input->base + SENINF_CSI2_INT_EN);
> + /* Write clear CSI2 IRQ */
> + writel(0xffffffff, input->base + SENINF_CSI2_INT_STATUS);
> + /* Enable CSI2 Extend IRQ mask */
> + /* Turn on all interrupt */
> + mtk_seninf_input_update(input, SENINF_CTRL, CSI2_SW_RST, 1);
> + udelay(1);
> + mtk_seninf_input_update(input, SENINF_CTRL, CSI2_SW_RST, 0);
> +}
> +
> +static void mtk_seninf_mux_setup(struct mtk_seninf_mux *mux,
> + struct mtk_seninf_input *input,
> + struct v4l2_subdev_state *state)
> +{
> + const struct mtk_seninf_format_info *fmtinfo;
> + const struct v4l2_mbus_framefmt *format;
> + unsigned int pix_sel_ext;
> + unsigned int pix_sel;
> + unsigned int hs_pol = 0;
> + unsigned int vs_pol = 0;
> + unsigned int val;
> + u32 rst_mask;
> +
> + format = v4l2_subdev_state_get_stream_format(state, input->pad, 0);
> + fmtinfo = mtk_seninf_format_info(format->code);
> +
> + /* Enable mux */
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_MUX_EN, 1);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_SRC_SEL, SENINF_MIPI_SENSOR);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL_EXT, SENINF_SRC_SEL_EXT, SENINF_NORMAL_MODEL);
Could you run
./scripts/checkpatch.pl --strict --max-line-length=80
on the set?
There are probably reasons to do otherwise for e.g. register definitions or
where you really can't do that without breaking other CodingStyle rules.
> +
> + pix_sel_ext = 0;
> + pix_sel = 1;
These local variables are redundant.
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL_EXT, SENINF_PIX_SEL_EXT, pix_sel_ext);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_PIX_SEL, pix_sel);
> +
> + if (fmtinfo->flags & MTK_SENINF_FORMAT_JPEG) {
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_FULL_WR_EN, 0);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_FLUSH_EN,
> + FIFO_FLUSH_EN_JPEG_2_PIXEL_MODE);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_PUSH_EN,
> + FIFO_PUSH_EN_JPEG_2_PIXEL_MODE);
> + } else {
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_FULL_WR_EN, 2);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_FLUSH_EN,
> + FIFO_FLUSH_EN_NORMAL_MODE);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_PUSH_EN,
> + FIFO_PUSH_EN_NORMAL_MODE);
> + }
> +
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_HSYNC_POL, hs_pol);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_VSYNC_POL, vs_pol);
Same for vs_pol. Or should you get the value from the endpoint?
> +
> + val = mtk_seninf_mux_read(mux, SENINF_MUX_CTRL);
> + rst_mask = SENINF_MUX_CTRL_SENINF_IRQ_SW_RST | SENINF_MUX_CTRL_SENINF_MUX_SW_RST;
> +
> + mtk_seninf_mux_write(mux, SENINF_MUX_CTRL, val | rst_mask);
> + mtk_seninf_mux_write(mux, SENINF_MUX_CTRL, val & ~rst_mask);
> +
> + /* HQ */
> + mtk_seninf_mux_write(mux, SENINF_MUX_SPARE, 0xc2000);
> +}
> +
> +static void mtk_seninf_top_mux_setup(struct mtk_seninf *priv,
> + enum mtk_seninf_id seninf_id,
> + struct mtk_seninf_mux *mux)
> +{
> + unsigned int val;
> +
> + /*
> + * Use the top mux (from SENINF input to MUX) to configure routing, and
> + * hardcode a 1:1 mapping from the MUX instances to the SENINF outputs.
> + */
> + val = readl(priv->base + SENINF_TOP_MUX_CTRL)
> + & ~(0xf << (mux->mux_id * 4));
Alignment.
> + val |= (seninf_id & 0xf) << (mux->mux_id * 4);
> + writel(val, priv->base + SENINF_TOP_MUX_CTRL);
> +
> + writel(0x76541010, priv->base + SENINF_TOP_CAM_MUX_CTRL);
What does this do? A comment would be nice, and even nicer it would be to
have a macro (or macros) for constructing this magic number using them.
> +}
> +
> +static void seninf_enable_test_pattern(struct mtk_seninf *priv,
> + struct v4l2_subdev_state *state)
> +{
> + struct mtk_seninf_input *input = &priv->inputs[CSI_PORT_0];
> + struct mtk_seninf_mux *mux = &priv->muxes[0];
> + const struct mtk_seninf_format_info *fmtinfo;
> + const struct v4l2_mbus_framefmt *format;
> + unsigned int val;
> + unsigned int pix_sel_ext;
> + unsigned int pix_sel;
> + unsigned int hs_pol = 0;
> + unsigned int vs_pol = 0;
> + unsigned int seninf = 0;
> + unsigned int tm_size = 0;
> + unsigned int mux_id = mux->mux_id;
> +
> + format = v4l2_subdev_state_get_stream_format(state, priv->conf->nb_inputs, 0);
> + fmtinfo = mtk_seninf_format_info(format->code);
> +
> + mtk_seninf_update(priv, SENINF_TOP_CTRL, MUX_LP_MODE, 0);
> +
> + mtk_seninf_update(priv, SENINF_TOP_CTRL, SENINF_PCLK_EN, 1);
> + mtk_seninf_update(priv, SENINF_TOP_CTRL, SENINF2_PCLK_EN, 1);
> +
> + mtk_seninf_input_update(input, SENINF_CTRL, SENINF_EN, 1);
> + mtk_seninf_input_update(input, SENINF_CTRL, SENINF_SRC_SEL, 1);
> + mtk_seninf_input_update(input, SENINF_CTRL_EXT,
> + SENINF_TESTMDL_IP_EN, 1);
> +
> + mtk_seninf_input_update(input, SENINF_TG1_TM_CTL, TM_EN, 1);
> + mtk_seninf_input_update(input, SENINF_TG1_TM_CTL, TM_PAT, 0xc);
> + mtk_seninf_input_update(input, SENINF_TG1_TM_CTL, TM_VSYNC, 4);
> + mtk_seninf_input_update(input, SENINF_TG1_TM_CTL, TM_DUMMYPXL, 0x28);
> +
> + if (fmtinfo->flags & MTK_SENINF_FORMAT_BAYER)
> + mtk_seninf_input_update(input, SENINF_TG1_TM_CTL, TM_FMT, 0x0);
> + else
> + mtk_seninf_input_update(input, SENINF_TG1_TM_CTL, TM_FMT, 0x1);
> +
> + tm_size = FIELD_PREP(SENINF_TG1_TM_SIZE_TM_LINE, format->height + 8);
> + switch (format->code) {
> + case MEDIA_BUS_FMT_UYVY8_1X16:
> + case MEDIA_BUS_FMT_VYUY8_1X16:
> + case MEDIA_BUS_FMT_YUYV8_1X16:
> + case MEDIA_BUS_FMT_YVYU8_1X16:
> + tm_size |= FIELD_PREP(SENINF_TG1_TM_SIZE_TM_PXL, format->width * 2);
> + break;
> + default:
> + tm_size |= FIELD_PREP(SENINF_TG1_TM_SIZE_TM_PXL, format->width);
> + break;
> + }
> + writel(tm_size, input->base + SENINF_TG1_TM_SIZE);
> +
> + writel(TEST_MODEL_CLK_DIVIDED_CNT, input->base + SENINF_TG1_TM_CLK);
> + writel(TIME_STAMP_DIVIDER, input->base + SENINF_TG1_TM_STP);
> +
> + /* Set top mux */
> + val = (readl(priv->base + SENINF_TOP_MUX_CTRL) & (~(0xf << (mux_id * 4)))) |
> + ((seninf & 0xf) << (mux_id * 4));
> + writel(val, priv->base + SENINF_TOP_MUX_CTRL);
> +
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_MUX_EN, 1);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL_EXT,
> + SENINF_SRC_SEL_EXT, SENINF_TEST_MODEL);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_SRC_SEL, 1);
> +
> + pix_sel_ext = 0;
> + pix_sel = 1;
> +
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL_EXT,
> + SENINF_PIX_SEL_EXT, pix_sel_ext);
> +
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_PIX_SEL, pix_sel);
> +
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_PUSH_EN, 0x1f);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_FLUSH_EN, 0x1b);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, FIFO_FULL_WR_EN, 2);
> +
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_HSYNC_POL, hs_pol);
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_VSYNC_POL, vs_pol);
These seem to be redundant.
> + mtk_seninf_mux_update(mux, SENINF_MUX_CTRL, SENINF_HSYNC_MASK, 1);
> +
> + mtk_seninf_mux_write(mux, SENINF_MUX_INTEN,
> + SENINF_IRQ_CLR_SEL | SENINF_ALL_ERR_IRQ_EN);
> +
> + mtk_seninf_mux_write(mux, SENINF_MUX_CTRL,
> + mtk_seninf_mux_read(mux, SENINF_MUX_CTRL) |
> + SENINF_MUX_CTRL_SENINF_IRQ_SW_RST |
> + SENINF_MUX_CTRL_SENINF_MUX_SW_RST);
> + udelay(1);
> + mtk_seninf_mux_write(mux, SENINF_MUX_CTRL,
> + mtk_seninf_mux_read(mux, SENINF_MUX_CTRL) &
> + ~(SENINF_MUX_CTRL_SENINF_IRQ_SW_RST |
> + SENINF_MUX_CTRL_SENINF_MUX_SW_RST));
> +
> + //check this
/* comment */
> + writel(0x76540010, priv->base + SENINF_TOP_CAM_MUX_CTRL);
> +
> + dev_dbg(priv->dev, "%s: OK\n", __func__);
This can certainly be removed.
> +}
> +
> +static void mtk_seninf_start(struct mtk_seninf *priv,
> + struct v4l2_subdev_state *state,
> + struct mtk_seninf_input *input,
> + struct mtk_seninf_mux *mux)
> +{
> + phy_power_on(input->phy);
> +
> + mtk_seninf_input_setup_csi2_rx(input);
> + mtk_seninf_input_setup_csi2(input, state);
> +
> + mtk_seninf_mux_setup(mux, input, state);
> + mtk_seninf_top_mux_setup(priv, input->seninf_id, mux);
> +}
> +
> +static void mtk_seninf_stop(struct mtk_seninf *priv,
> + struct mtk_seninf_input *input)
> +{
> + unsigned int val;
> +
> + /* Disable CSI2(2.5G) first */
> + val = readl(input->base + SENINF_CSI2_CTL);
> + val &= ~(SENINF_CSI2_CTL_CLOCK_LANE_EN |
> + SENINF_CSI2_CTL_DATA_LANE3_EN |
> + SENINF_CSI2_CTL_DATA_LANE2_EN |
> + SENINF_CSI2_CTL_DATA_LANE1_EN |
> + SENINF_CSI2_CTL_DATA_LANE0_EN);
> + writel(val, input->base + SENINF_CSI2_CTL);
> +
> + if (!priv->is_testmode)
> + phy_power_off(input->phy);
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * V4L2 Controls
> + */
> +
> +static int seninf_set_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct mtk_seninf *priv = container_of(ctrl->handler,
> + struct mtk_seninf, ctrl_handler);
> +
> + switch (ctrl->id) {
> + case V4L2_CID_TEST_PATTERN:
> + priv->is_testmode = !!ctrl->val;
You could instead store the pointer to the control and use ctrl->val where
you need this.
> + break;
> + }
> +
> + return 0;
> +}
> +
> +static const struct v4l2_ctrl_ops seninf_ctrl_ops = {
> + .s_ctrl = seninf_set_ctrl,
> +};
> +
> +static const char *const seninf_test_pattern_menu[] = {
> + "No test pattern",
> + "Static horizontal color bars",
> +};
> +
> +static int seninf_initialize_controls(struct mtk_seninf *priv)
> +{
> + struct v4l2_ctrl_handler *handler;
> + int ret;
> +
> + handler = &priv->ctrl_handler;
> + ret = v4l2_ctrl_handler_init(handler, 2);
> + if (ret)
> + return ret;
> +
> + v4l2_ctrl_new_std_menu_items(handler, &seninf_ctrl_ops,
> + V4L2_CID_TEST_PATTERN,
> + ARRAY_SIZE(seninf_test_pattern_menu) - 1,
> + 0, 0, seninf_test_pattern_menu);
> +
> + priv->is_testmode = false;
> +
> + if (handler->error) {
> + ret = handler->error;
> + dev_err(priv->dev,
> + "Failed to init controls(%d)\n", ret);
> + v4l2_ctrl_handler_free(handler);
> + return ret;
> + }
> +
> + priv->subdev.ctrl_handler = handler;
> +
> + return 0;
> +}
> +
> +/* -----------------------------------------------------------------------------
> + * V4L2 Subdev Operations
> + */
> +static int seninf_s_stream(struct v4l2_subdev *sd, unsigned int source_pad,
> + int on)
> +{
> + struct mtk_seninf *priv = sd_to_mtk_seninf(sd);
> + struct v4l2_subdev_state *state;
> + struct mtk_seninf_input *input;
> + struct mtk_seninf_mux *mux;
> + struct v4l2_subdev *source;
> + u32 sink_pad;
> + int ret;
> +
> + /* Stream control can only operate on source pads. */
> + if (source_pad < priv->conf->nb_inputs ||
> + source_pad >= priv->conf->nb_inputs + priv->conf->nb_outputs)
> + return -EINVAL;
> +
> + /*
> + * Locate the SENINF input and MUX for the source pad.
> + *
> + * Hardcode a 1:1 mapping of MUX instances to SENINF
> + * outputs to match the TOP_CAM_MUX configuration in
> + * mtk_seninf_top_mux_setup().
> + */
> + state = v4l2_subdev_lock_and_get_active_state(&priv->subdev);
> + if (!state)
> + return -EPIPE;
> +
> + ret = v4l2_subdev_routing_find_opposite_end(&state->routing, source_pad, 0, &sink_pad,
> + NULL);
> + if (ret) {
> + dev_dbg(priv->dev, "No sink pad routed to source pad %u\n", source_pad);
> + goto unlock;
> + }
> +
> + input = &priv->inputs[sink_pad];
> + mux = &priv->muxes[source_pad - priv->conf->nb_inputs];
> +
> + if (!on) {
> + if (!priv->is_testmode) {
> + source = input->source_sd;
> + ret = v4l2_subdev_call(source, video, s_stream, 0);
> + if (ret)
> + dev_err(priv->dev,
> + "failed to stop source %s: %d\n",
> + source->entity.name, ret);
> + }
> +
> + mtk_seninf_stop(priv, input);
> + pm_runtime_put(priv->dev);
> + goto unlock;
> + }
> +
> + ret = pm_runtime_get_sync(priv->dev);
> + if (ret < 0) {
> + dev_err(priv->dev, "Failed to pm_runtime_get_sync: %d\n", ret);
> + pm_runtime_put_noidle(priv->dev);
> + goto unlock;
> + }
> +
> + /* If test mode is enabled, just enable the test pattern generator. */
> + if (priv->is_testmode) {
> + seninf_enable_test_pattern(priv, state);
> + ret = 0;
> + goto unlock;
> + }
> +
> + /* Start the SENINF first and then the source. */
> + mtk_seninf_start(priv, state, input, mux);
> +
> + source = input->source_sd;
> + ret = v4l2_subdev_call(source, video, s_stream, 1);
> + if (ret) {
> + dev_err(priv->dev, "failed to start source %s: %d\n",
> + source->entity.name, ret);
> + mtk_seninf_stop(priv, input);
> + pm_runtime_put(priv->dev);
> + }
> +
> +unlock:
> + v4l2_subdev_unlock_state(state);
> + return ret;
> +};
> +
> +static int seninf_enable_streams(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state, u32 pad,
> + u64 streams_mask)
> +{
> + return seninf_s_stream(sd, pad, 1);
> +}
> +
> +static int seninf_disable_streams(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state, u32 pad,
> + u64 streams_mask)
> +{
> + return seninf_s_stream(sd, pad, 0);
> +}
> +
> +static const struct v4l2_mbus_framefmt mtk_seninf_default_fmt = {
> + .code = SENINF_DEFAULT_BUS_FMT,
> + .width = SENINF_DEFAULT_WIDTH,
> + .height = SENINF_DEFAULT_HEIGHT,
> + .field = V4L2_FIELD_NONE,
> + .colorspace = V4L2_COLORSPACE_SRGB,
> + .xfer_func = V4L2_XFER_FUNC_DEFAULT,
> + .ycbcr_enc = V4L2_YCBCR_ENC_DEFAULT,
> + .quantization = V4L2_QUANTIZATION_DEFAULT,
> +};
> +
> +static int __seninf_set_routing(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + struct v4l2_subdev_krouting *routing)
> +{
> + int ret;
> +
> + ret = v4l2_subdev_routing_validate(sd, routing, V4L2_SUBDEV_ROUTING_ONLY_1_TO_1);
> + if (ret)
> + return ret;
> +
> + ret = v4l2_subdev_set_routing_with_fmt(sd, state, routing,
> + &mtk_seninf_default_fmt);
return ...;
> +
> + if (ret)
> + return ret;
> +
> + return 0;
> +}
> +
> +static int seninf_init_cfg(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state)
> +{
> + struct mtk_seninf *priv = sd_to_mtk_seninf(sd);
> + struct v4l2_subdev_route routes[SENINF_MAX_NUM_OUTPUTS] = { };
> + struct v4l2_subdev_krouting routing = {
> + .routes = routes,
> + };
> + unsigned int i;
> +
> + /*
> + * Initialize one route for supported source pads.
> + * It is a single route from the first sink pad to the source pad,
> + * while on SENINF 5.0 the routing table will map sink pads to source
> + * pads connected to CAMSV 1:1 (skipping the first two source pads
> + * connected to the CAM instances).
> + */
> + routing.num_routes = priv->conf->nb_outputs;
You can do this assignment in the declaration.
> +
> + for (i = 0; i < routing.num_routes; i++) {
> + struct v4l2_subdev_route *route = &routes[i];
> +
> + route->sink_pad = i;
> + route->sink_stream = 0;
> + route->source_pad = priv->conf->nb_inputs + i;
> + route->source_stream = 0;
> + route->flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE;
> + }
> +
> + return __seninf_set_routing(sd, state, &routing);
> +}
> +
> +static int seninf_enum_mbus_code(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + struct v4l2_subdev_mbus_code_enum *code)
> +{
> + const struct mtk_seninf_format_info *fmtinfo;
> + struct mtk_seninf *priv = sd_to_mtk_seninf(sd);
> +
> + if (code->index >= ARRAY_SIZE(mtk_seninf_formats))
> + return -EINVAL;
> +
> + fmtinfo = &mtk_seninf_formats[code->index];
> + if (fmtinfo->flags & MTK_SENINF_FORMAT_INPUT_ONLY &&
> + mtk_seninf_pad_is_source(priv, code->pad))
> + return -EINVAL;
> +
> + code->code = fmtinfo->code;
> +
> + return 0;
> +}
> +
> +static int seninf_set_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + struct v4l2_subdev_format *fmt)
> +{
> + struct mtk_seninf *priv = sd_to_mtk_seninf(sd);
> + const struct mtk_seninf_format_info *fmtinfo;
> + struct v4l2_mbus_framefmt *format;
> +
> + /*
> + * TODO (?): We should disallow setting formats on the source pad
> + * completely, as the SENINF can't perform any processing. This would
> + * however break usage of the test pattern generator, as there would be
> + * no way to configure formats at all when no active input is selected.
> + */
Could you instead expose the TPG as a new sub-device? We'll have internal
pads, too, in the future.
> +
> + /*
> + * Default to the first format if the requested media bus code isn't
> + * supported.
> + */
> + fmtinfo = mtk_seninf_format_info(fmt->format.code);
> + if (!fmtinfo) {
> + fmtinfo = &mtk_seninf_formats[0];
> + fmt->format.code = fmtinfo->code;
> + }
> +
> + /* Interlaced formats are not supported yet. */
> + fmt->format.field = V4L2_FIELD_NONE;
> +
> + /* Store the format. */
> + format = v4l2_subdev_state_get_stream_format(state, fmt->pad, fmt->stream);
> + if (!format)
> + return -EINVAL;
> +
> + *format = fmt->format;
> +
> + if (mtk_seninf_pad_is_source(priv, fmt->pad))
> + return 0;
> +
> + /* Propagate the format to the corresponding source pad. */
> + format = v4l2_subdev_state_get_opposite_stream_format(state, fmt->pad,
> + fmt->stream);
> + if (!format)
> + return -EINVAL;
> +
> + *format = fmt->format;
> +
> + return 0;
> +}
> +
> +static int seninf_set_routing(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + enum v4l2_subdev_format_whence which,
> + struct v4l2_subdev_krouting *routing)
> +{
> + return __seninf_set_routing(sd, state, routing);
> +}
> +
> +static const struct v4l2_subdev_core_ops seninf_subdev_core_ops = {
> + .subscribe_event = v4l2_ctrl_subdev_subscribe_event,
> + .unsubscribe_event = v4l2_event_subdev_unsubscribe,
> +};
> +
> +static const struct v4l2_subdev_pad_ops seninf_subdev_pad_ops = {
> + .init_cfg = seninf_init_cfg,
> + .enum_mbus_code = seninf_enum_mbus_code,
> + .get_fmt = v4l2_subdev_get_fmt,
> + .set_fmt = seninf_set_fmt,
> + .link_validate = v4l2_subdev_link_validate_default,
> + .set_routing = seninf_set_routing,
> + .enable_streams = seninf_enable_streams,
> + .disable_streams = seninf_disable_streams,
> +};
> +
> +static const struct v4l2_subdev_ops seninf_subdev_ops = {
> + .core = &seninf_subdev_core_ops,
> + .pad = &seninf_subdev_pad_ops,
> +};
> +
> +/* -----------------------------------------------------------------------------
> + * Media Entity Operations
> + */
> +
> +static const struct media_entity_operations seninf_media_ops = {
> + .get_fwnode_pad = v4l2_subdev_get_fwnode_pad_1_to_1,
> + .link_validate = v4l2_subdev_link_validate,
> +};
> +
> +/* -----------------------------------------------------------------------------
> + * Async Subdev Notifier
> + */
> +
> +struct mtk_seninf_async_subdev {
> + struct v4l2_async_connection asc;
> + struct mtk_seninf_input *input;
> + unsigned int port;
> +};
> +
> +static int mtk_seninf_fwnode_parse(struct device *dev,
> + unsigned int id)
A better name for "id" would be "port".
> +
> +{
> + static const char * const phy_names[] = { "csi0", "csi1", "csi2", "csi0b"};
> + struct mtk_seninf *priv = dev_get_drvdata(dev);
> + struct fwnode_handle *ep, *fwnode;
> + struct mtk_seninf_input *input;
> + struct mtk_seninf_async_subdev *asd;
> + struct v4l2_fwnode_endpoint vep = {
> + .bus_type = V4L2_MBUS_CSI2_DPHY,
> + };
Fits on a single line.
> + unsigned int port;
> + int ret;
> +
> + ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), id, 0, 0);
> + if (!ep)
> + return 0;
> +
> + fwnode = fwnode_graph_get_remote_endpoint(ep);
> + ret = v4l2_fwnode_endpoint_parse(ep, &vep);
> + if (ret) {
> + dev_err(dev, "Failed to parse %pOF\n", to_of_node(fwnode));
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + asd = v4l2_async_nf_add_fwnode(&priv->notifier, fwnode,
> + struct mtk_seninf_async_subdev);
> + if (IS_ERR(asd)) {
> + ret = PTR_ERR(asd);
> + goto out;
> + }
> +
> + port = vep.base.port;
> + asd->port = port;
> +
> + if (mtk_seninf_pad_is_source(priv, port)) {
> + ret = 0;
> + goto out;
> + }
> +
> + if (vep.bus_type != V4L2_MBUS_CSI2_DPHY) {
As you requested D-PHY, there's no longer need to check it here.
(v4l2_fwnode_endpoint_parse() returns an error otherwise.)
> + dev_err(dev, "Only CSI2 bus type is currently supported\n");
> + ret = -EINVAL;
> + goto out;
> + }
> +
> + input = &priv->inputs[port];
> +
> + input->pad = port;
> + input->seninf_id = port_to_seninf_id[port];
> + input->base = priv->base + 0x1000 * input->seninf_id;
> + input->seninf = priv;
> +
> + input->bus = vep.bus.mipi_csi2;
> +
> + input->phy = devm_phy_get(dev, phy_names[port]);
> + if (IS_ERR(input->phy)) {
> + dev_err(dev, "failed to get phy:%ld\n", PTR_ERR(input->phy));
> + ret = PTR_ERR(input->phy);
> + goto out;
> + }
> + input->phy_mode = SENINF_PHY_MODE_4D1C;
> +
> + asd->input = input;
> +
> + ret = 0;
> +out:
> + fwnode_handle_put(ep);
> + fwnode_handle_put(fwnode);
> + return ret;
> +}
> +
> +static int mtk_seninf_notifier_bound(struct v4l2_async_notifier *notifier,
> + struct v4l2_subdev *sd,
> + struct v4l2_async_connection *asc)
> +{
> + struct mtk_seninf *priv = container_of(notifier, struct mtk_seninf, notifier);
> + struct mtk_seninf_async_subdev *asd =
> + container_of(asc, struct mtk_seninf_async_subdev, asc);
> + struct device_link *link;
> + int ret;
> +
> + dev_dbg(priv->dev, "%s bound to SENINF port %u\n", sd->entity.name, asd->port);
> +
> + if (mtk_seninf_pad_is_sink(priv, asd->port)) {
> + struct mtk_seninf_input *input = asd->input;
> +
> + input->source_sd = sd;
> +
> + link = device_link_add(priv->dev, sd->dev,
> + DL_FLAG_PM_RUNTIME | DL_FLAG_STATELESS);
Could you explain a little why do you need a device link here? Same below
actually.
> + if (!link) {
> + dev_err(priv->dev,
> + "Failed to create device link from source %s\n", sd->name);
> + return -EINVAL;
> + }
> +
> + ret = v4l2_create_fwnode_links_to_pad(sd, &priv->pads[input->pad],
> + MEDIA_LNK_FL_IMMUTABLE |
> + MEDIA_LNK_FL_ENABLED);
> + } else {
> + link = device_link_add(sd->dev, priv->dev,
> + DL_FLAG_PM_RUNTIME | DL_FLAG_STATELESS);
> + if (!link) {
> + dev_err(priv->dev,
> + "Failed to create device link to output %s\n", sd->name);
> + return -EINVAL;
> + }
> +
> + ret = v4l2_create_fwnode_links_to_pad(&priv->subdev,
> + &sd->entity.pads[0],
> + MEDIA_LNK_FL_IMMUTABLE |
> + MEDIA_LNK_FL_ENABLED);
> + }
> + if (ret) {
> + dev_err(priv->dev, "Failed to create links between SENINF port %u and %s (%d)\n",
> + asd->port, sd->entity.name, ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int mtk_seninf_notifier_complete(struct v4l2_async_notifier *notifier)
> +{
> + struct mtk_seninf *priv = container_of(notifier, struct mtk_seninf, notifier);
> + int ret;
> +
> + ret = v4l2_device_register_subdev_nodes(&priv->v4l2_dev);
> + if (ret) {
> + dev_err(priv->dev, "Failed to register subdev nodes: %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct v4l2_async_notifier_operations mtk_seninf_async_ops = {
> + .bound = mtk_seninf_notifier_bound,
> + .complete = mtk_seninf_notifier_complete,
> +};
> +
> +static int mtk_seninf_media_init(struct mtk_seninf *priv)
> +{
> + struct media_device *media_dev = &priv->media_dev;
> + const struct mtk_seninf_conf *conf = priv->conf;
> + u8 num_pads = conf->nb_outputs + conf->nb_inputs;
unsigned int?
> + struct media_pad *pads = priv->pads;
> + struct device *dev = priv->dev;
> + unsigned int i;
> + int ret;
> +
> + media_dev->dev = dev;
> + strscpy(media_dev->model, conf->model, sizeof(media_dev->model));
> + snprintf(media_dev->bus_info, sizeof(media_dev->bus_info),
> + "platform:%s", dev_name(dev));
media_device_init() already does this.
> + media_dev->hw_revision = 0;
> + media_device_init(media_dev);
> +
> + for (i = 0; i < conf->nb_inputs; i++)
> + pads[i].flags = MEDIA_PAD_FL_SINK;
> + for (i = conf->nb_inputs; i < num_pads; i++)
> + pads[i].flags = MEDIA_PAD_FL_SOURCE;
> +
> + ret = media_entity_pads_init(&priv->subdev.entity, num_pads, pads);
> + if (ret) {
> + media_device_cleanup(media_dev);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int mtk_seninf_v4l2_async_register(struct mtk_seninf *priv)
> +{
> + const struct mtk_seninf_conf *conf = priv->conf;
> + struct device *dev = priv->dev;
> + unsigned int i;
> + int ret;
> +
> + v4l2_async_nf_init(&priv->notifier, &priv->v4l2_dev);
> +
> + for (i = 0; i < conf->nb_inputs + conf->nb_outputs; ++i) {
> + ret = mtk_seninf_fwnode_parse(dev, i);
> +
> + if (ret) {
> + dev_err(dev, "Failed to parse endpoint at port %d, err: %d\n", i, ret);
> + goto err_clean_notififer;
> + }
> + }
> +
> + priv->notifier.ops = &mtk_seninf_async_ops;
> + ret = v4l2_async_nf_register(&priv->notifier);
> + if (ret) {
> + dev_err(dev, "Failed to register async notifier: %d\n", ret);
> + goto err_clean_notififer;
> + }
> + return 0;
> +
> +err_clean_notififer:
> + v4l2_async_nf_cleanup(&priv->notifier);
> +
> + return ret;
> +}
> +
> +static int mtk_seninf_v4l2_register(struct mtk_seninf *priv)
> +{
> + struct v4l2_subdev *sd = &priv->subdev;
> + struct device *dev = priv->dev;
> + int ret;
> +
> + /* Initialize media device & pads. */
> + ret = mtk_seninf_media_init(priv);
> + if (ret)
> + return ret;
> +
> + /* Initialize & register v4l2 device. */
> + priv->v4l2_dev.mdev = &priv->media_dev;
> +
> + ret = v4l2_device_register(dev, &priv->v4l2_dev);
> + if (ret) {
> + dev_err_probe(dev, ret, "Failed to register V4L2 device: %d\n", ret);
> + goto err_clean_media;
> + }
> +
> + /* Initialize & register subdev. */
> + v4l2_subdev_init(sd, &seninf_subdev_ops);
> + sd->dev = dev;
> + sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
> + sd->entity.ops = &seninf_media_ops;
> + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS
> + | V4L2_SUBDEV_FL_STREAMS;
Alignment. '|' should also be on the previous line, i.e. wrap after it.
The same applies to the rest of the set, too.
> + strscpy(sd->name, dev_name(dev), sizeof(sd->name));
> + ret = seninf_initialize_controls(priv);
> + if (ret) {
> + dev_err_probe(dev, ret, "Failed to initialize controls: %d\n", ret);
> + goto err_unreg_v4l2;
> + }
> + v4l2_set_subdevdata(sd, priv);
> +
> + ret = v4l2_subdev_init_finalize(sd);
> + if (ret)
> + goto err_free_handler;
> +
> + ret = v4l2_device_register_subdev(&priv->v4l2_dev, sd);
> + if (ret) {
> + dev_err_probe(dev, ret, "Failed to register subdev: %d\n", ret);
> + goto err_cleanup_subdev;
> + }
> +
> + /* Set up async device */
> + ret = mtk_seninf_v4l2_async_register(priv);
> + if (ret) {
> + dev_err_probe(dev, ret, "Failed to register v4l2 async notifier: %d\n", ret);
> + goto err_unreg_subdev;
> + }
> +
> + /* Register media device */
> + ret = media_device_register(&priv->media_dev);
> + if (ret) {
> + dev_err_probe(dev, ret, "failed to register media device: %d\n", ret);
> + goto err_unreg_notifier;
> + }
> +
> + return 0;
> +
> +err_unreg_notifier:
> + v4l2_async_nf_unregister(&priv->notifier);
> +err_unreg_subdev:
> + v4l2_device_unregister_subdev(sd);
> +err_cleanup_subdev:
> + v4l2_subdev_cleanup(sd);
> +err_free_handler:
> + v4l2_ctrl_handler_free(&priv->ctrl_handler);
> +err_unreg_v4l2:
> + v4l2_device_unregister(&priv->v4l2_dev);
> +err_clean_media:
> + media_entity_cleanup(&sd->entity);
> + media_device_cleanup(&priv->media_dev);
> +
> + return ret;
> +}
> +
> +static int seninf_probe(struct platform_device *pdev)
> +{
> + /* List of clocks required by seninf. */
I think this comment is redundant.
> + static const char * const clk_names[] = { "camsys", "top_mux" };
> + struct device *dev = &pdev->dev;
> + struct mtk_seninf *priv;
> + unsigned int i;
> + int ret;
> +
> + priv = devm_kzalloc(dev, sizeof(struct mtk_seninf), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + priv->conf = of_device_get_match_data(dev);
> +
> + dev_set_drvdata(dev, priv);
> + priv->dev = dev;
> +
> + priv->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + priv->num_clks = ARRAY_SIZE(clk_names);
> + priv->clks = devm_kcalloc(dev, priv->num_clks,
> + sizeof(*priv->clks), GFP_KERNEL);
> + if (!priv->clks)
> + return -ENOMEM;
> +
> + for (i = 0; i < priv->num_clks; ++i)
> + priv->clks[i].id = clk_names[i];
> +
> + ret = devm_clk_bulk_get(dev, priv->num_clks, priv->clks);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to get seninf clock:%d\n", ret);
> +
> + for (i = 0; i < priv->conf->nb_muxes; ++i) {
> + struct mtk_seninf_mux *mux = &priv->muxes[i];
> +
> + mux->pad = priv->conf->nb_inputs + i;
> + mux->mux_id = i;
> + mux->base = priv->base + 0x1000 * i;
> + mux->seninf = priv;
> + }
> +
> + ret = mtk_seninf_v4l2_register(priv);
> + if (ret)
> + return ret;
> +
> + devm_pm_runtime_enable(dev);
> +
> + return ret;
> +}
> +
> +static int seninf_pm_suspend(struct device *dev)
> +{
> + struct mtk_seninf *priv = dev_get_drvdata(dev);
> +
> + dev_dbg(dev, "seninf runtime suspend\n");
Maybe this could be removed?
> + clk_bulk_disable_unprepare(priv->num_clks, priv->clks);
> +
> + return 0;
> +}
> +
> +static int seninf_pm_resume(struct device *dev)
> +{
> + struct mtk_seninf *priv = dev_get_drvdata(dev);
> + int ret;
> +
> + dev_dbg(dev, "seninf runtime resume\n");
This, too.
> + ret = clk_bulk_prepare_enable(priv->num_clks, priv->clks);
> + if (ret) {
> + dev_err(dev, "failed to enable clock:%d\n", ret);
> + return ret;
> + }
> +
> + mtk_seninf_csi2_setup_phy(priv);
> +
> + return 0;
> +}
> +
> +static const struct dev_pm_ops runtime_pm_ops = {
> + SET_RUNTIME_PM_OPS(seninf_pm_suspend, seninf_pm_resume, NULL)
> + SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend, pm_runtime_force_resume)
> +};
> +
> +static int seninf_remove(struct platform_device *pdev)
> +{
> + struct mtk_seninf *priv = dev_get_drvdata(&pdev->dev);
> +
> + media_device_unregister(&priv->media_dev);
> + media_device_cleanup(&priv->media_dev);
> + v4l2_async_nf_unregister(&priv->notifier);
> + v4l2_async_nf_cleanup(&priv->notifier);
> + v4l2_device_unregister_subdev(&priv->subdev);
> + v4l2_subdev_cleanup(&priv->subdev);
> + v4l2_ctrl_handler_free(&priv->ctrl_handler);
> + media_entity_cleanup(&priv->subdev.entity);
> + v4l2_device_unregister(&priv->v4l2_dev);
> +
> + return 0;
> +}
> +
> +static const struct mtk_seninf_conf seninf_8365_conf = {
> + .model = "mtk-camsys-3.0",
> + .nb_inputs = 4,
> + .nb_muxes = 6,
> + .nb_outputs = 4,
> +};
> +
> +static const struct of_device_id mtk_seninf_of_match[] = {
> + { .compatible = "mediatek,mt8365-seninf", .data = &seninf_8365_conf },
> + { /* sentinel */ },
> +};
> +MODULE_DEVICE_TABLE(of, mtk_seninf_of_match);
> +
> +static struct platform_driver seninf_pdrv = {
> + .driver = {
> + .name = "mtk-seninf",
> + .pm = &runtime_pm_ops,
> + .of_match_table = mtk_seninf_of_match,
> + },
> + .probe = seninf_probe,
> + .remove = seninf_remove,
> +};
> +
> +module_platform_driver(seninf_pdrv);
> +
> +MODULE_DESCRIPTION("MTK sensor interface driver");
> +MODULE_AUTHOR("Louis Kuo <louis.kuo at mediatek.com>");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf_reg.h b/drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf_reg.h
> new file mode 100644
> index 000000000000..768ad5d641be
> --- /dev/null
> +++ b/drivers/media/platform/mediatek/isp/isp_30/seninf/mtk_seninf_reg.h
> @@ -0,0 +1,112 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (c) 2022 MediaTek Inc.
> + */
> +
> +#ifndef __SENINF_REG_H__
> +#define __SENINF_REG_H__
> +
> +#include <linux/bits.h>
> +
> +#define SENINF_TOP_CTRL 0x0000
> +#define SENINF_TOP_CTRL_MUX_LP_MODE BIT(31)
> +#define SENINF_TOP_CTRL_SENINF_PCLK_EN BIT(10)
> +#define SENINF_TOP_CTRL_SENINF2_PCLK_EN BIT(11)
> +#define SENINF_TOP_MUX_CTRL 0x0008
> +#define SENINF_TOP_CAM_MUX_CTRL 0x0010
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI0 0x001c
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI0_DPHY_MODE BIT(0)
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI0_CK_SEL_1 GENMASK(10, 8)
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI0_CK_SEL_2 GENMASK(13, 12)
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI0_PHY_SENINF_LANE_MUX_CSI0_EN BIT(31)
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI1 0x0020
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI1_DPHY_MODE BIT(0)
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI1_CK_SEL_1 GENMASK(10, 8)
> +#define SENINF_TOP_PHY_SENINF_CTL_CSI1_PHY_SENINF_LANE_MUX_CSI1_EN BIT(31)
> +#define SENINF_CTRL 0x0200
> +#define SENINF_CTRL_SENINF_EN BIT(0)
> +#define SENINF_CTRL_CSI2_SW_RST BIT(7)
> +#define SENINF_CTRL_SENINF_SRC_SEL GENMASK(14, 12)
> +#define SENINF_CTRL_PAD2CAM_DATA_SEL GENMASK(30, 28)
> +#define SENINF_CTRL_EXT 0x0204
> +#define SENINF_CTRL_EXT_SENINF_TESTMDL_IP_EN BIT(1)
> +#define SENINF_CTRL_EXT_SENINF_NCSI2_IP_EN BIT(5)
> +#define SENINF_CTRL_EXT_SENINF_CSI2_IP_EN BIT(6)
> +#define SENINF_TG1_PH_CNT 0x0600
> +#define SENINF_TG1_SEN_CK 0x0604
> +#define SENINF_TG1_TM_CTL 0x0608
> +#define SENINF_TG1_TM_CTL_TM_EN BIT(0)
> +#define SENINF_TG1_TM_CTL_TM_FMT BIT(2)
> +#define SENINF_TG1_TM_CTL_TM_PAT GENMASK(7, 4)
> +#define SENINF_TG1_TM_CTL_TM_VSYNC GENMASK(15, 8)
> +#define SENINF_TG1_TM_CTL_TM_DUMMYPXL GENMASK(23, 16)
> +#define SENINF_TG1_TM_SIZE 0x060c
> +#define SENINF_TG1_TM_SIZE_TM_LINE GENMASK(29, 16)
> +#define SENINF_TG1_TM_SIZE_TM_PXL GENMASK(12, 0)
> +#define SENINF_TG1_TM_CLK 0x0610
> +#define TEST_MODEL_CLK_DIVIDED_CNT 8
> +#define SENINF_TG1_TM_STP 0x0614
> +#define TIME_STAMP_DIVIDER 1
> +#define MIPI_RX_CON24_CSI0 0x0824
> +#define MIPI_RX_CON24_CSI0_CSI0_BIST_LN0_MUX GENMASK(25, 24)
> +#define MIPI_RX_CON24_CSI0_CSI0_BIST_LN1_MUX GENMASK(27, 26)
> +#define MIPI_RX_CON24_CSI0_CSI0_BIST_LN2_MUX GENMASK(29, 28)
> +#define MIPI_RX_CON24_CSI0_CSI0_BIST_LN3_MUX GENMASK(31, 30)
> +#define SENINF_CSI2_CTL 0x0a00
> +#define SENINF_CSI2_CTL_DATA_LANE0_EN BIT(0)
> +#define SENINF_CSI2_CTL_DATA_LANE1_EN BIT(1)
> +#define SENINF_CSI2_CTL_DATA_LANE2_EN BIT(2)
> +#define SENINF_CSI2_CTL_DATA_LANE3_EN BIT(3)
> +#define SENINF_CSI2_CTL_CLOCK_LANE_EN BIT(4)
> +#define SENINF_CSI2_CTL_HSRX_DET_EN BIT(7)
> +#define SENINF_CSI2_CTL_ED_SEL BIT(16)
> +#define DATA_HEADER_ORDER_DI_WCL_WCH 1
> +#define SENINF_CSI2_CTL_HS_TRAIL_EN BIT(25)
> +#define SENINF_CSI2_CTL_CLOCK_HS_OPTION BIT(27)
> +#define SENINF_CSI2_LNRD_TIMING 0x0a08
> +#define SENINF_CSI2_LNRD_TIMING_DATA_SETTLE_PARAMETER GENMASK(15, 8)
> +#define SENINF_CSI2_DPCM 0x0a0c
> +#define SENINF_CSI2_DPCM_DI_30_DPCM_EN BIT(7)
> +#define SENINF_CSI2_DPCM_DI_2A_DPCM_EN BIT(15)
> +#define SENINF_CSI2_INT_EN 0x0a10
> +#define SENINF_CSI2_INT_STATUS 0x0a14
> +#define SENINF_CSI2_DGB_SEL 0x0a18
> +#define SENINF_CSI2_DGB_SEL_DEBUG_SEL GENMASK(7, 0)
> +#define SENINF_CSI2_DGB_SEL_DEBUG_EN BIT(31)
> +#define SENINF_CSI2_SPARE0 0x0a20
> +#define SENINF_CSI2_LNRC_FSM 0x0a28
> +#define SENINF_CSI2_HS_TRAIL 0x0a40
> +#define SENINF_CSI2_HS_TRAIL_HS_TRAIL_PARAMETER GENMASK(7, 0)
> +#define SENINF_CSI2_RESYNC_MERGE_CTL 0x0a74
> +#define SENINF_CSI2_RESYNC_MERGE_CTL_CPHY_LANE_RESYNC_CNT GENMASK(2, 0)
> +#define SENINF_CSI2_RESYNC_MERGE_CTL_BYPASS_LANE_RESYNC BIT(10)
> +#define SENINF_CSI2_RESYNC_MERGE_CTL_CDPHY_SEL BIT(11)
> +#define SENINF_CSI2_MODE 0x0ae8
> +#define SENINF_CSI2_MODE_CSR_CSI2_MODE GENMASK(7, 0)
> +#define SENINF_CSI2_MODE_CSR_CSI2_HEADER_LEN GENMASK(10, 8)
> +#define SENINF_CSI2_DPHY_SYNC 0x0b20
> +#define SENINF_CSI2_DPHY_SYNC_SYNC_SEQ_MASK_0 GENMASK(15, 0)
> +#define SENINF_CSI2_DPHY_SYNC_SYNC_SEQ_PAT_0 GENMASK(31, 16)
> +#define SENINF_MUX_CTRL 0x0d00
> +#define SENINF_MUX_CTRL_SENINF_MUX_SW_RST BIT(0)
> +#define SENINF_MUX_CTRL_SENINF_IRQ_SW_RST BIT(1)
> +#define SENINF_MUX_CTRL_SENINF_HSYNC_MASK BIT(7)
> +#define SENINF_MUX_CTRL_SENINF_PIX_SEL BIT(8)
> +#define SENINF_MUX_CTRL_SENINF_VSYNC_POL BIT(9)
> +#define SENINF_MUX_CTRL_SENINF_HSYNC_POL BIT(10)
> +#define SENINF_MUX_CTRL_SENINF_SRC_SEL GENMASK(15, 12)
> +#define SENINF_MUX_CTRL_FIFO_PUSH_EN GENMASK(21, 16)
> +#define FIFO_PUSH_EN_NORMAL_MODE 0x1f
> +#define FIFO_PUSH_EN_JPEG_2_PIXEL_MODE 0x1e
> +#define SENINF_MUX_CTRL_FIFO_FLUSH_EN GENMASK(28, 22)
> +#define FIFO_FLUSH_EN_NORMAL_MODE 0x1b
> +#define FIFO_FLUSH_EN_JPEG_2_PIXEL_MODE 0x18
> +#define SENINF_MUX_CTRL_FIFO_FULL_WR_EN GENMASK(29, 28)
> +#define SENINF_MUX_CTRL_SENINF_MUX_EN BIT(31)
> +#define SENINF_MUX_INTEN 0x0d04
> +#define SENINF_MUX_SPARE 0x0d2c
> +#define SENINF_MUX_CTRL_EXT 0x0d3c
> +#define SENINF_MUX_CTRL_EXT_SENINF_SRC_SEL_EXT GENMASK(1, 0)
> +#define SENINF_MUX_CTRL_EXT_SENINF_PIX_SEL_EXT BIT(4)
> +
> +#endif /* __SENINF_REG_H__ */
--
Kind regards,
Sakari Ailus
More information about the Linux-mediatek
mailing list