[PATCH v2 2/2] arm64: dts: mediatek: Introduce the MT8395 Radxa NIO 12L board
AngeloGioacchino Del Regno
angelogioacchino.delregno at collabora.com
Fri Feb 2 03:48:21 PST 2024
Add a device tree for the Radxa NIO 12L SBC, powered by the MediaTek
MT8395 Genio 1200 SoC.
This board features:
* MT6359 + MT6360 PMICs at I2C-6
- Regulators, battery charger, TypeC Port Controller Interface
- Audio through 3.5mm jack (2CH out, 1CH in)
* Two MT6315 PMICs over SPMI
- CPU-Big and GPU Core regulators
* Network Connectivity
- Realtek RTL8211FD MDIO PHY/Transceiver, 10/100/1000M Ethernet
- MT7921E WiFi (PCIe1) / Bluetooth (USB 2.0) combo chip
* Storage
- On-board UFS storage
- On-board eMMC on MMC0 controller
- MicroSD card slot on MMC1 controller
* Other connectivity
- 1x USB Type-C Charging/Power only port
- 1x USB 3.2 SuperSpeed Type-C OTG+DisplayPort mode
- Muxed by ITE IT5205 Alternate Mode Passive MUX
- 4x USB 3.0 Type-A ports on VL805 USB Hub (PCIe0)
- 1x HDMI IN port
- 1x HDMI OUT port
- 1x MIPI DSI (Display) port
- 2x MIPI CSI (Camera) ports
* 40-pin Expansion Header
- Two UART ports
- I2C, SPI busses
- I2S for external audio chips
- ADC
- GPIOs
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../dts/mediatek/mt8395-radxa-nio-12l.dts | 825 ++++++++++++++++++
2 files changed, 826 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 1e6f91731e92..fdd8f4a58003 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -63,4 +63,5 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-genio-1200-evk.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-radxa-nio-12l.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts b/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
new file mode 100644
index 000000000000..e5d9b671a405
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8395-radxa-nio-12l.dts
@@ -0,0 +1,825 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2023 Radxa Limited
+ * Copyright (C) 2024 Collabora Ltd.
+ * AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
+ */
+
+#include "mt8195.dtsi"
+#include "mt6359.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/usb/pd.h>
+
+/ {
+ model = "Radxa NIO 12L";
+ chassis-type = "embedded";
+ compatible = "radxa,nio-12l", "mediatek,mt8395", "mediatek,mt8195";
+
+ aliases {
+ i2c0 = &i2c2;
+ i2c1 = &i2c3;
+ i2c2 = &i2c4;
+ i2c3 = &i2c0;
+ i2c4 = &i2c1;
+ ethernet0 = ð
+ serial0 = &uart0;
+ serial1 = &uart1;
+ spi0 = &spi1;
+ spi1 = &spi2;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ memory at 40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0x1 0x0>;
+ };
+
+ wifi_vreg: regulator-wifi-3v3-en {
+ compatible = "regulator-fixed";
+ regulator-name = "wifi_3v3_en";
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 67 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_vreg_pins>;
+ vin-supply = <&vsys>;
+ };
+
+ /* system wide switching 5.0V power rail */
+ vsys: regulator-vsys {
+ compatible = "regulator-fixed";
+ regulator-name = "vsys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_vsys>;
+ };
+
+ vsys_buck: regulator-vsys-buck {
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_buck";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_vsys>;
+ };
+
+ /* Rail from power-only "TYPE C DC" port */
+ vcc5v0_vsys: regulator-vcc5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /*
+ * 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee at 43200000 {
+ reg = <0 0x43200000 0 0xc00000>;
+ no-map;
+ };
+
+ scp_mem: memory at 50000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x50000000 0 0x2900000>;
+ no-map;
+ };
+
+ vpu_mem: memory at 53000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x53000000 0 0x1400000>; /* 20 MB */
+ };
+
+ /* 2 MiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_mem: memory at 54600000 {
+ reg = <0 0x54600000 0x0 0x200000>;
+ no-map;
+ };
+
+ afe_mem: memory at 60000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x60000000 0 0x1100000>;
+ no-map;
+ };
+
+ apu_mem: memory at 62000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x62000000 0 0x1400000>; /* 20 MB */
+ };
+ };
+};
+
+ð {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&rgmii_phy>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <ð_default_pins>;
+ pinctrl-1 = <ð_sleep_pins>;
+ mediatek,tx-delay-ps = <2030>;
+ mediatek,mac-wol;
+ snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>;
+ snps,reset-delays-us = <0 20000 100000>;
+ status = "okay";
+
+ mdio {
+ rgmii_phy: ethernet-phy at 1 {
+ compatible = "ethernet-phy-id001c.c916";
+ reg = <0x1>;
+ };
+ };
+};
+
+&gpu {
+ mali-supply = <&mt6315_7_vbuck1>;
+ status = "okay";
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ typec-mux at 48 {
+ compatible = "ite,it5205";
+ reg = <0x48>;
+
+ mode-switch;
+ orientation-switch;
+
+ vcc-supply = <&mt6359_vibr_ldo_reg>;
+
+ port {
+ it5205_sbu_mux: endpoint {
+ remote-endpoint = <&typec_con_mux>;
+ };
+ };
+ };
+};
+
+&i2c4 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /* I2C4 exposed at 39-pins MIPI-LCD connector */
+};
+
+&i2c6 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c6_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ mt6360: pmic at 34 {
+ compatible = "mediatek,mt6360";
+ reg = <0x34>;
+ interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-names = "IRQB";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ pinctrl-0 = <&mt6360_pins>;
+
+ charger {
+ compatible = "mediatek,mt6360-chg";
+ richtek,vinovp-microvolt = <14500000>;
+
+ otg_vbus_regulator: usb-otg-vbus-regulator {
+ regulator-name = "usb-otg-vbus";
+ regulator-min-microvolt = <4425000>;
+ regulator-max-microvolt = <5825000>;
+ };
+ };
+
+ regulator {
+ compatible = "mediatek,mt6360-regulator";
+ LDO_VIN1-supply = <&vsys_buck>;
+ LDO_VIN3-supply = <&mt6360_buck2>;
+
+ mt6360_buck1: buck1 {
+ regulator-name = "emi_vdd2";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP
+ MT6360_OPMODE_ULP>;
+ regulator-always-on;
+ };
+
+ mt6360_buck2: buck2 {
+ regulator-name = "emi_vddq";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP
+ MT6360_OPMODE_ULP>;
+ regulator-always-on;
+ };
+
+ mt6360_ldo1: ldo1 {
+ regulator-name = "ext_lcd_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP>;
+ regulator-always-on;
+ };
+
+ mt6360_ldo2: ldo2 {
+ regulator-name = "panel1_p1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP>;
+ };
+
+ mt6360_ldo3: ldo3 {
+ regulator-name = "vmc_pmu";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP>;
+ };
+
+ mt6360_ldo5: ldo5 {
+ regulator-name = "vmch_pmu";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP>;
+ regulator-always-on;
+ };
+
+ mt6360_ldo6: ldo6 {
+ regulator-name = "mt6360_ldo6"; /* Test point */
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP>;
+ };
+
+ mt6360_ldo7: ldo7 {
+ regulator-name = "emi_vmddr_en";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2100000>;
+ regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+ MT6360_OPMODE_LP>;
+ regulator-always-on;
+ };
+ };
+
+ typec {
+ compatible = "mediatek,mt6360-tcpc";
+ interrupts-extended = <&pio 100 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "PD_IRQB";
+
+ connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ op-sink-microwatt = <10000000>;
+ power-role = "dual";
+ try-power-role = "sink";
+
+ source-pdos = <PDO_FIXED(5000, 1000,
+ PDO_FIXED_DUAL_ROLE |
+ PDO_FIXED_DATA_SWAP)>;
+ sink-pdos = <PDO_FIXED(5000, 3000,
+ PDO_FIXED_DUAL_ROLE |
+ PDO_FIXED_DATA_SWAP)>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ typec_con_hs: endpoint {
+ remote-endpoint = <&mtu3_hs0_role_sw>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ typec_con_mux: endpoint {
+ remote-endpoint = <&it5205_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+ };
+};
+
+/* MMC0 Controller: eMMC (HS400). Power lines are shared with UFS! */
+&mmc0 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_default_pins>;
+ pinctrl-1 = <&mmc0_uhs_pins>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ hs400-ds-delay = <0x14c11>;
+ cap-mmc-highspeed;
+ cap-mmc-hw-reset;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ no-sdio;
+ no-sd;
+ non-removable;
+ vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+ vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+ status = "okay";
+};
+
+/* MMC1 Controller: MicroSD card slot */
+&mmc1 {
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc1_default_pins>, <&mmc1_pins_detect>;
+ pinctrl-1 = <&mmc1_default_pins>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ cap-sd-highspeed;
+ cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
+ no-mmc;
+ no-sdio;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&mt6360_ldo5>;
+ vqmmc-supply = <&mt6360_ldo3>;
+ status = "okay";
+};
+
+&mt6359_vaud18_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vbbck_ldo_reg {
+ regulator-always-on;
+};
+
+/* For USB Hub */
+&mt6359_vcamio_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcn33_2_bt_ldo_reg {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+};
+
+&mt6359_vcore_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vproc1_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vproc2_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vpu_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vsram_md_ldo_reg {
+ regulator-always-on;
+};
+
+/* for GPU SRAM */
+&mt6359_vsram_others_ldo_reg {
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+};
+
+&pio {
+ eth_default_pins: eth-default-pins {
+ pins-cc {
+ pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>,
+ <PINMUX_GPIO86__FUNC_GBE_RXC>,
+ <PINMUX_GPIO87__FUNC_GBE_RXDV>,
+ <PINMUX_GPIO88__FUNC_GBE_TXEN>;
+ drive-strength = <8>;
+ };
+
+ pins-mdio {
+ pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>,
+ <PINMUX_GPIO90__FUNC_GBE_MDIO>;
+ input-enable;
+ };
+
+ pins-power {
+ pinmux = <PINMUX_GPIO91__FUNC_GPIO91>,
+ <PINMUX_GPIO92__FUNC_GPIO92>;
+ output-high;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO93__FUNC_GPIO93>;
+ };
+
+ pins-rxd {
+ pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>,
+ <PINMUX_GPIO82__FUNC_GBE_RXD2>,
+ <PINMUX_GPIO83__FUNC_GBE_RXD1>,
+ <PINMUX_GPIO84__FUNC_GBE_RXD0>;
+ };
+
+ pins-txd {
+ pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>,
+ <PINMUX_GPIO78__FUNC_GBE_TXD2>,
+ <PINMUX_GPIO79__FUNC_GBE_TXD1>,
+ <PINMUX_GPIO80__FUNC_GBE_TXD0>;
+ drive-strength = <8>;
+ };
+ };
+
+ eth_sleep_pins: eth-sleep-pins {
+ pins-cc {
+ pinmux = <PINMUX_GPIO85__FUNC_GPIO85>,
+ <PINMUX_GPIO86__FUNC_GPIO86>,
+ <PINMUX_GPIO87__FUNC_GPIO87>,
+ <PINMUX_GPIO88__FUNC_GPIO88>;
+ };
+
+ pins-mdio {
+ pinmux = <PINMUX_GPIO89__FUNC_GPIO89>,
+ <PINMUX_GPIO90__FUNC_GPIO90>;
+ bias-disable;
+ input-disable;
+ };
+
+ pins-rxd {
+ pinmux = <PINMUX_GPIO81__FUNC_GPIO81>,
+ <PINMUX_GPIO82__FUNC_GPIO82>,
+ <PINMUX_GPIO83__FUNC_GPIO83>,
+ <PINMUX_GPIO84__FUNC_GPIO84>;
+ };
+
+ pins-txd {
+ pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
+ <PINMUX_GPIO78__FUNC_GPIO78>,
+ <PINMUX_GPIO79__FUNC_GPIO79>,
+ <PINMUX_GPIO80__FUNC_GPIO80>;
+ };
+ };
+
+ i2c2_pins: i2c2-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO12__FUNC_SDA2>,
+ <PINMUX_GPIO13__FUNC_SCL2>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+ drive-strength = <6>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c4_pins: i2c4-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO16__FUNC_SDA4>,
+ <PINMUX_GPIO17__FUNC_SCL4>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c6_pins: i2c6-pins {
+ pins {
+ pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
+ <PINMUX_GPIO26__FUNC_SCL6>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+ };
+ };
+
+ mmc0_default_pins: mmc0-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ drive-strength = <6>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+ <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+ <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+ <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+ <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+ <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+ <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+ <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+ <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ drive-strength = <6>;
+ input-enable;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ drive-strength = <6>;
+ };
+ };
+
+ mmc0_uhs_pins: mmc0-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ drive-strength = <8>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+ <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+ <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+ <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+ <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+ <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+ <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+ <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+ <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ drive-strength = <8>;
+ input-enable;
+ };
+
+ pins-ds {
+ pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ drive-strength = <8>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ drive-strength = <8>;
+ };
+ };
+
+ mmc1_default_pins: mmc1-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ drive-strength = <8>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+ <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+ <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+ <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+ <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ drive-strength = <8>;
+ input-enable;
+ };
+ };
+
+ mmc1_pins_detect: mmc1-detect-pins {
+ pins-insert {
+ pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
+ bias-pull-up;
+ };
+ };
+
+ mt6360_pins: mt6360-pins {
+ pins-irq {
+ pinmux = <PINMUX_GPIO100__FUNC_GPIO100>,
+ <PINMUX_GPIO101__FUNC_GPIO101>;
+ input-enable;
+ bias-pull-up;
+ };
+ };
+
+ pcie0_default_pins: pcie0-default-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO19__FUNC_WAKEN>,
+ <PINMUX_GPIO20__FUNC_PERSTN>,
+ <PINMUX_GPIO21__FUNC_CLKREQN>;
+ bias-pull-up;
+ };
+ };
+
+ pcie1_default_pins: pcie1-default-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO0__FUNC_PERSTN_1>,
+ <PINMUX_GPIO1__FUNC_CLKREQN_1>,
+ <PINMUX_GPIO2__FUNC_WAKEN_1>;
+ bias-disable;
+ };
+ };
+
+ spi1_pins: spi1-default-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO136__FUNC_SPIM1_CSB>,
+ <PINMUX_GPIO137__FUNC_SPIM1_CLK>,
+ <PINMUX_GPIO138__FUNC_SPIM1_MO>,
+ <PINMUX_GPIO139__FUNC_SPIM1_MI>;
+ bias-disable;
+ };
+ };
+
+ spi2_pins: spi2-default-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO140__FUNC_SPIM2_CSB>,
+ <PINMUX_GPIO141__FUNC_SPIM2_CLK>,
+ <PINMUX_GPIO142__FUNC_SPIM2_MO>,
+ <PINMUX_GPIO143__FUNC_SPIM2_MI>;
+ bias-disable;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
+ <PINMUX_GPIO99__FUNC_URXD0>;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins-bus {
+ pinmux = <PINMUX_GPIO102__FUNC_UTXD1>,
+ <PINMUX_GPIO103__FUNC_URXD1>;
+ };
+ };
+
+ wifi_vreg_pins: wifi-vreg-pins {
+ pins-wifi-pmu-en {
+ pinmux = <PINMUX_GPIO65__FUNC_GPIO65>;
+ output-high;
+ };
+
+ pins-wifi-vreg-en {
+ pinmux = <PINMUX_GPIO67__FUNC_GPIO67>;
+ };
+ };
+};
+
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie0_default_pins>;
+ status = "okay";
+};
+
+&pcie1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie1_default_pins>;
+ status = "okay";
+};
+
+&pmic {
+ interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&scp {
+ memory-region = <&scp_mem>;
+ status = "okay";
+};
+
+&spi1 {
+ /* Exposed at 40 pin connector */
+ pinctrl-0 = <&spi1_pins>;
+ pinctrl-names = "default";
+ mediatek,pad-select = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+};
+
+&spi2 {
+ /* Exposed at 40 pin connector */
+ pinctrl-0 = <&spi2_pins>;
+ pinctrl-names = "default";
+ mediatek,pad-select = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+};
+
+&spmi {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ mt6315_6: pmic at 6 {
+ compatible = "mediatek,mt6315-regulator";
+ reg = <0x6 SPMI_USID>;
+
+ regulators {
+ mt6315_6_vbuck1: vbuck1 {
+ regulator-compatible = "vbuck1";
+ regulator-name = "Vbcpu";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1193750>;
+ regulator-enable-ramp-delay = <256>;
+ regulator-allowed-modes = <0 1 2>;
+ regulator-always-on;
+ };
+ };
+ };
+
+ mt6315_7: pmic at 7 {
+ compatible = "mediatek,mt6315-regulator";
+ reg = <0x7 SPMI_USID>;
+
+ regulators {
+ mt6315_7_vbuck1: vbuck1 {
+ regulator-compatible = "vbuck1";
+ regulator-name = "Vgpu";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1193750>;
+ regulator-enable-ramp-delay = <256>;
+ regulator-allowed-modes = <0 1 2>;
+ };
+ };
+ };
+};
+
+&uart0 {
+ /* Exposed at 40 pin connector */
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ /* Exposed at 40 pin connector */
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&ssusb0 {
+ role-switch-default-mode = "host";
+ usb-role-switch;
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+ status = "okay";
+
+ port {
+ mtu3_hs0_role_sw: endpoint {
+ remote-endpoint = <&typec_con_hs>;
+ };
+ };
+};
+
+&ssusb2 {
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+ status = "okay";
+};
+
+&xhci0 {
+ vbus-supply = <&otg_vbus_regulator>;
+ status = "okay";
+};
+
+&xhci1 {
+ /* MT7921's USB Bluetooth has issues with USB2 LPM */
+ usb2-lpm-disable;
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+ vbus-supply = <&vsys>;
+ status = "okay";
+};
+
+&xhci2 {
+ vbus-supply = <&vsys>;
+ status = "okay";
+};
--
2.43.0
More information about the Linux-mediatek
mailing list