[PATCH net-next 06/13] net: dsa: mt7530: refactor MT7530_HWTRAP and MT7530_MHWTRAP
Arınç ÜNAL via B4 Relay
devnull+arinc.unal.arinc9.com at kernel.org
Fri Apr 19 03:09:29 PDT 2024
From: Arınç ÜNAL <arinc.unal at arinc9.com>
The MT7530_HWTRAP and MT7530_MHWTRAP registers are on MT7530 and MT7531.
It's called hardware trap on MT7530, software trap on MT7531. That's
because some bits of the trap on MT7530 cannot be modified by software
whilst all bits of the trap on MT7531 can. Rename the definitions for them
to MT753X_TRAP and MT753X_MTRAP. Add MT7530 and MT7531 prefixes to the
definitions specific to the switch model.
Remove the extra parentheses from MT7530_XTAL_40MHZ and MT7530_XTAL_20MHZ.
Rename MHWTRAP_PHY0_SEL, MHWTRAP_MANUAL, and MHWTRAP_PHY_ACCESS to be on
par with the "MT7621 Giga Switch Programming Guide v0.3" document.
Make an enumaration for the XTAL frequency. Set the data type of the xtal
variable on mt7531_pll_setup() to it.
Signed-off-by: Arınç ÜNAL <arinc.unal at arinc9.com>
---
drivers/net/dsa/mt7530.c | 59 ++++++++++++++++++++++++------------------------
drivers/net/dsa/mt7530.h | 50 ++++++++++++++++++++--------------------
2 files changed, 54 insertions(+), 55 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 39c47499036b..606516206fb9 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -417,23 +417,23 @@ mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
mt7530_rmw(priv, MT7530_P6ECR, P6_INTF_MODE_MASK, P6_INTF_MODE(1));
- xtal = mt7530_read(priv, MT7530_MHWTRAP) & HWTRAP_XTAL_MASK;
+ xtal = mt7530_read(priv, MT753X_MTRAP) & MT7530_XTAL_MASK;
- if (xtal == HWTRAP_XTAL_25MHZ)
+ if (xtal == MT7530_XTAL_25MHZ)
ssc_delta = 0x57;
else
ssc_delta = 0x87;
if (priv->id == ID_MT7621) {
/* PLL frequency: 125MHz: 1.0GBit */
- if (xtal == HWTRAP_XTAL_40MHZ)
+ if (xtal == MT7530_XTAL_40MHZ)
ncpo1 = 0x0640;
- if (xtal == HWTRAP_XTAL_25MHZ)
+ if (xtal == MT7530_XTAL_25MHZ)
ncpo1 = 0x0a00;
} else { /* PLL frequency: 250MHz: 2.0Gbit */
- if (xtal == HWTRAP_XTAL_40MHZ)
+ if (xtal == MT7530_XTAL_40MHZ)
ncpo1 = 0x0c80;
- if (xtal == HWTRAP_XTAL_25MHZ)
+ if (xtal == MT7530_XTAL_25MHZ)
ncpo1 = 0x1400;
}
@@ -456,19 +456,20 @@ mt7530_setup_port6(struct dsa_switch *ds, phy_interface_t interface)
static void
mt7531_pll_setup(struct mt7530_priv *priv)
{
+ enum mt7531_xtal_fsel xtal;
u32 top_sig;
u32 hwstrap;
- u32 xtal;
u32 val;
val = mt7530_read(priv, MT7531_CREV);
top_sig = mt7530_read(priv, MT7531_TOP_SIG_SR);
- hwstrap = mt7530_read(priv, MT7531_HWTRAP);
+ hwstrap = mt7530_read(priv, MT753X_TRAP);
if ((val & CHIP_REV_M) > 0)
- xtal = (top_sig & PAD_MCM_SMI_EN) ? HWTRAP_XTAL_FSEL_40MHZ :
- HWTRAP_XTAL_FSEL_25MHZ;
+ xtal = (top_sig & PAD_MCM_SMI_EN) ? MT7531_XTAL_FSEL_40MHZ :
+ MT7531_XTAL_FSEL_25MHZ;
else
- xtal = hwstrap & HWTRAP_XTAL_FSEL_MASK;
+ xtal = (hwstrap & MT7531_XTAL25) ? MT7531_XTAL_FSEL_25MHZ :
+ MT7531_XTAL_FSEL_40MHZ;
/* Step 1 : Disable MT7531 COREPLL */
val = mt7530_read(priv, MT7531_PLLGP_EN);
@@ -497,13 +498,13 @@ mt7531_pll_setup(struct mt7530_priv *priv)
usleep_range(25, 35);
switch (xtal) {
- case HWTRAP_XTAL_FSEL_25MHZ:
+ case MT7531_XTAL_FSEL_25MHZ:
val = mt7530_read(priv, MT7531_PLLGP_CR0);
val &= ~RG_COREPLL_SDM_PCW_M;
val |= 0x140000 << RG_COREPLL_SDM_PCW_S;
mt7530_write(priv, MT7531_PLLGP_CR0, val);
break;
- case HWTRAP_XTAL_FSEL_40MHZ:
+ case MT7531_XTAL_FSEL_40MHZ:
val = mt7530_read(priv, MT7531_PLLGP_CR0);
val &= ~RG_COREPLL_SDM_PCW_M;
val |= 0x190000 << RG_COREPLL_SDM_PCW_S;
@@ -877,20 +878,20 @@ static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
mutex_lock(&priv->reg_mutex);
- val = mt7530_read(priv, MT7530_MHWTRAP);
+ val = mt7530_read(priv, MT753X_MTRAP);
- val |= MHWTRAP_MANUAL | MHWTRAP_P5_MAC_SEL | MHWTRAP_P5_DIS;
- val &= ~MHWTRAP_P5_RGMII_MODE & ~MHWTRAP_PHY0_SEL;
+ val |= MT7530_CHG_TRAP | MT7530_P5_MAC_SEL | MT7530_P5_DIS;
+ val &= ~MT7530_P5_RGMII_MODE & ~MT7530_P5_PHY0_SEL;
switch (priv->p5_mode) {
/* MUX_PHY_P0: P0 -> P5 -> SoC MAC */
case MUX_PHY_P0:
- val |= MHWTRAP_PHY0_SEL;
+ val |= MT7530_P5_PHY0_SEL;
fallthrough;
/* MUX_PHY_P4: P4 -> P5 -> SoC MAC */
case MUX_PHY_P4:
- val &= ~MHWTRAP_P5_MAC_SEL & ~MHWTRAP_P5_DIS;
+ val &= ~MT7530_P5_MAC_SEL & ~MT7530_P5_DIS;
/* Setup the MAC by default for the cpu port */
mt7530_write(priv, MT753X_PMCR_P(5), 0x56300);
@@ -898,13 +899,13 @@ static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
/* GMAC5: P5 -> SoC MAC or external PHY */
default:
- val &= ~MHWTRAP_P5_DIS;
+ val &= ~MT7530_P5_DIS;
break;
}
/* Setup RGMII settings */
if (phy_interface_mode_is_rgmii(interface)) {
- val |= MHWTRAP_P5_RGMII_MODE;
+ val |= MT7530_P5_RGMII_MODE;
/* P5 RGMII RX Clock Control: delay setting for 1000M */
mt7530_write(priv, MT7530_P5RGMIIRXCR, CSR_RGMII_EDGE_ALIGN);
@@ -924,7 +925,7 @@ static void mt7530_setup_port5(struct dsa_switch *ds, phy_interface_t interface)
P5_IO_CLK_DRV(1) | P5_IO_DATA_DRV(1));
}
- mt7530_write(priv, MT7530_MHWTRAP, val);
+ mt7530_write(priv, MT753X_MTRAP, val);
dev_dbg(ds->dev, "Setup P5, HWTRAP=0x%x, mode=%s, phy-mode=%s\n", val,
mt7530_p5_mode_str(priv->p5_mode), phy_modes(interface));
@@ -2365,7 +2366,7 @@ mt7530_setup(struct dsa_switch *ds)
}
/* Waiting for MT7530 got to stable */
- INIT_MT7530_DUMMY_POLL(&p, priv, MT7530_HWTRAP);
+ INIT_MT7530_DUMMY_POLL(&p, priv, MT753X_TRAP);
ret = readx_poll_timeout(_mt7530_read, &p, val, val != 0,
20, 1000000);
if (ret < 0) {
@@ -2380,7 +2381,7 @@ mt7530_setup(struct dsa_switch *ds)
return -ENODEV;
}
- if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_20MHZ) {
+ if ((val & MT7530_XTAL_MASK) == MT7530_XTAL_20MHZ) {
dev_err(priv->dev,
"MT7530 with a 20MHz XTAL is not supported!\n");
return -EINVAL;
@@ -2401,12 +2402,12 @@ mt7530_setup(struct dsa_switch *ds)
RD_TAP_MASK, RD_TAP(16));
/* Enable port 6 */
- val = mt7530_read(priv, MT7530_MHWTRAP);
- val &= ~MHWTRAP_P6_DIS & ~MHWTRAP_PHY_ACCESS;
- val |= MHWTRAP_MANUAL;
- mt7530_write(priv, MT7530_MHWTRAP, val);
+ val = mt7530_read(priv, MT753X_MTRAP);
+ val &= ~MT7530_P6_DIS & ~MT7530_PHY_INDIRECT_ACCESS;
+ val |= MT7530_CHG_TRAP;
+ mt7530_write(priv, MT753X_MTRAP, val);
- if ((val & HWTRAP_XTAL_MASK) == HWTRAP_XTAL_40MHZ)
+ if ((val & MT7530_XTAL_MASK) == MT7530_XTAL_40MHZ)
mt7530_pll_setup(priv);
mt753x_trap_frames(priv);
@@ -2586,7 +2587,7 @@ mt7531_setup(struct dsa_switch *ds)
}
/* Waiting for MT7530 got to stable */
- INIT_MT7530_DUMMY_POLL(&p, priv, MT7530_HWTRAP);
+ INIT_MT7530_DUMMY_POLL(&p, priv, MT753X_TRAP);
ret = readx_poll_timeout(_mt7530_read, &p, val, val != 0,
20, 1000000);
if (ret < 0) {
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index c6ef20b7bbdd..1f3aeccc77be 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -495,32 +495,30 @@ enum mt7531_clk_skew {
MT7531_CLK_SKEW_REVERSE = 3,
};
-/* Register for hw trap status */
-#define MT7530_HWTRAP 0x7800
-#define HWTRAP_XTAL_MASK (BIT(10) | BIT(9))
-#define HWTRAP_XTAL_25MHZ (BIT(10) | BIT(9))
-#define HWTRAP_XTAL_40MHZ (BIT(10))
-#define HWTRAP_XTAL_20MHZ (BIT(9))
-
-#define MT7531_HWTRAP 0x7800
-#define HWTRAP_XTAL_FSEL_MASK BIT(7)
-#define HWTRAP_XTAL_FSEL_25MHZ BIT(7)
-#define HWTRAP_XTAL_FSEL_40MHZ 0
-/* Unique fields of (M)HWSTRAP for MT7531 */
-#define XTAL_FSEL_S 7
-#define XTAL_FSEL_M BIT(7)
-#define PHY_EN BIT(6)
-#define CHG_STRAP BIT(8)
-
-/* Register for hw trap modification */
-#define MT7530_MHWTRAP 0x7804
-#define MHWTRAP_PHY0_SEL BIT(20)
-#define MHWTRAP_MANUAL BIT(16)
-#define MHWTRAP_P5_MAC_SEL BIT(13)
-#define MHWTRAP_P6_DIS BIT(8)
-#define MHWTRAP_P5_RGMII_MODE BIT(7)
-#define MHWTRAP_P5_DIS BIT(6)
-#define MHWTRAP_PHY_ACCESS BIT(5)
+/* Register for trap status */
+#define MT753X_TRAP 0x7800
+#define MT7530_XTAL_MASK (BIT(10) | BIT(9))
+#define MT7530_XTAL_25MHZ (BIT(10) | BIT(9))
+#define MT7530_XTAL_40MHZ BIT(10)
+#define MT7530_XTAL_20MHZ BIT(9)
+#define MT7531_XTAL25 BIT(7)
+
+/* Register for trap modification */
+#define MT753X_MTRAP 0x7804
+#define MT7530_P5_PHY0_SEL BIT(20)
+#define MT7530_CHG_TRAP BIT(16)
+#define MT7530_P5_MAC_SEL BIT(13)
+#define MT7530_P6_DIS BIT(8)
+#define MT7530_P5_RGMII_MODE BIT(7)
+#define MT7530_P5_DIS BIT(6)
+#define MT7530_PHY_INDIRECT_ACCESS BIT(5)
+#define MT7531_CHG_STRAP BIT(8)
+#define MT7531_PHY_EN BIT(6)
+
+enum mt7531_xtal_fsel {
+ MT7531_XTAL_FSEL_25MHZ,
+ MT7531_XTAL_FSEL_40MHZ,
+};
/* Register for TOP signal control */
#define MT7530_TOP_SIG_CTRL 0x7808
--
2.40.1
More information about the Linux-mediatek
mailing list