[PATCH v4 2/2] arm64: dts: mediatek: add device-tree for Genio 700 EVK board
Macpaul Lin
macpaul.lin at mediatek.com
Fri Sep 15 01:12:12 PDT 2023
Add basic device-tree for the Genio 700 EVK board. The
Genio 700 EVK is based on MediaTek MT8390 SoC.
MT8390 hardware register maps are identical to MT8188.
The Genio 700 EVK has following features:
- MT8390 SoC
- MT6365 PMIC
- MT6319 Buck IC
- 12V DC Jack
- 2x4GB LPDDR4X
- 64GB eMMC 5.1
- 64Mb SPI NOR
- M.2 Key A-E slot with PCIe Gen2 and USB 2.0
- 2x DSI LCM ports
- 2x touch sensor ports
- 2x MIPI-CSI, as camera daughter board slots
- USB 2 micro USB connector
- USB 3 with 1 to 2 hub:
- M.2 Key B slot
- Type-C connector, with DisplayPort over Type-C
- HDMI 2.0 TX port with Type A HDMI connector
- eDP port
- Gigabit Ethernet with RJ45 connector
- SD card slot
- Earphone Jack
- Analog Microphone
- 2x Digital Microphone
- 3x UART with serial-to-usb converters and micro USB connectors
Signed-off-by: Chris-QJ Chen <chris-qj.chen at mediatek.com>
Signed-off-by: Pablo Sun <pablo.sun at mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin at mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno at collabora.com>
---
arch/arm64/boot/dts/mediatek/Makefile | 1 +
.../dts/mediatek/mt8390-genio-700-evk.dts | 880 ++++++++++++++++++
2 files changed, 881 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
dependencies for v1:
- This patch should be applied after the following patch set
- mt8365-gneio-350-evk's dts change (v4)
- https://lore.kernel.org/linux-arm-kernel/20230912092444.31635-1-macpaul.lin@mediatek.com/T/
- mt8395-genio-1200-evk's dts basic support (v6)
- https://lore.kernel.org/lkml/20230911115717.26184-1-macpaul.lin@mediatek.com/T/
- mt8188 platform's basic support
- https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@mediatek.com/T/
changes for v2:
- Fix gpio defines '0' to 'GPIO_ACTIVE_HIGH'.
- Drop duplicate name: 'default' for I2C4.
- Update dependencies
- mt8365-gneio-350-evk's dts change (v5)
- https://lore.kernel.org/lkml/20230913032226.4092-1-macpaul.lin@mediatek.com/
- mt8395-genio-1200-evk's dts basic support (v7)
- https://lore.kernel.org/linux-arm-kernel/20230913032057.3197-1-macpaul.lin@mediatek.com/T/
- mt8188 platform's basic support (v4)
- https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@mediatek.com/T/
changes for v3:
- No change.
- Update dependencies
- mt8365-gneio-350-evk's dts change (v5)
- https://lore.kernel.org/lkml/20230913032226.4092-1-macpaul.lin@mediatek.com/
- mt8395-genio-1200-evk's dts basic support (v8)
- https://lore.kernel.org/lkml/20230914055145.16801-1-macpaul.lin@mediatek.com/T/
- mt8188 platform's basic support (v4)
- https://lore.kernel.org/lkml/a4e1a80ebd19896410f50b0297e05dce06fb47cc.camel@mediatek.com/T/
changes for v4:
- Fix 'interrupts' of touchscreen on i2c0 to 'interrupts-extended'.
- Add 'Reviewed-by' tag, Thanks!
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 22f362bbbdac..3262849c0f6b 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -54,5 +54,6 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8365-genio-350-evk.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8390-genio-700-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8395-genio-1200-evk.dtb
dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
new file mode 100644
index 000000000000..6bb1d5d112ef
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-700-evk.dts
@@ -0,0 +1,880 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2023 MediaTek Inc.
+ * Author: Chris Chen <chris-qj.chen at mediatek.com>
+ * Pablo Sun <pablo.sun at mediatek.com>
+ * Macpaul Lin <macpaul.lin at mediatek.com>
+ */
+/dts-v1/;
+
+#include "mt8188.dtsi"
+#include "mt6359.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/mediatek,mt8188-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/usb/pd.h>
+
+/ {
+ model = "MediaTek Genio-700 EVK";
+ compatible = "mediatek,mt8390-evk", "mediatek,mt8390",
+ "mediatek,mt8188";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:921600n8";
+ };
+
+ firmware {
+ optee {
+ compatible = "linaro,optee-tz";
+ method = "smc";
+ };
+ };
+
+ memory at 40000000 {
+ device_type = "memory";
+ reg = <0 0x40000000 0x2 0x00000000>;
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /*
+ * 12 MiB reserved for OP-TEE (BL32)
+ * +-----------------------+ 0x43e0_0000
+ * | SHMEM 2MiB |
+ * +-----------------------+ 0x43c0_0000
+ * | | TA_RAM 8MiB |
+ * + TZDRAM +--------------+ 0x4340_0000
+ * | | TEE_RAM 2MiB |
+ * +-----------------------+ 0x4320_0000
+ */
+ optee_reserved: optee at 43200000 {
+ no-map;
+ reg = <0 0x43200000 0 0x00c00000>;
+ };
+
+ scp_mem: memory at 50000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x50000000 0 0x2900000>;
+ no-map;
+ };
+
+ /* 2 MiB reserved for ARM Trusted Firmware (BL31) */
+ bl31_secmon_reserved: memory at 54600000 {
+ no-map;
+ reg = <0 0x54600000 0x0 0x200000>;
+ };
+
+ apu_mem: memory at 55000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x55000000 0 0x1400000>; /* 20 MB */
+ };
+
+ vpu_mem: memory at 57000000 {
+ compatible = "shared-dma-pool";
+ reg = <0 0x57000000 0 0x1400000>; /* 20 MB */
+ };
+ };
+
+ common_fixed_5v: regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "5v_en";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ edp_panel_fixed_3v3: regulator-1 {
+ compatible = "regulator-fixed";
+ regulator-name = "edp_panel_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpio = <&pio 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&edp_panel_3v3_en_pins>;
+ };
+
+ gpio_fixed_3v3: regulator-2 {
+ compatible = "regulator-fixed";
+ regulator-name = "gpio_3v3_en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ sdio_fixed_1v8: regulator-3 {
+ compatible = "regulator-fixed";
+ regulator-name = "sdio_io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ sdio_fixed_3v3: regulator-4 {
+ compatible = "regulator-fixed";
+ regulator-name = "sdio_card";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 74 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ touch0_fixed_3v3: regulator-5 {
+ compatible = "regulator-fixed";
+ regulator-name = "touch_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 119 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_hub_fixed_3v3: regulator-6 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_hub_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&pio 112 GPIO_ACTIVE_HIGH>; /* HUB_3V3_EN */
+ startup-delay-us = <10000>;
+ enable-active-high;
+ };
+
+ usb_hub_reset_1v8: regulator-7 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_hub_reset";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ gpio = <&pio 7 GPIO_ACTIVE_HIGH>; /* HUB_RESET */
+ vin-supply = <&usb_hub_fixed_3v3>;
+ };
+
+ usb_p0_vbus: regulator-8 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_p0_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 84 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_p1_vbus: regulator-9 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_p1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&pio 87 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_p2_vbus: regulator-10 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_p2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ };
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ touchscreen at 5d {
+ compatible = "goodix,gt9271";
+ reg = <0x5d>;
+ interrupt-parent = <&pio>;
+ interrupts-extended = <&pio 6 IRQ_TYPE_EDGE_RISING>;
+ irq-gpios = <&pio 6 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>;
+ AVDD28-supply = <&touch0_fixed_3v3>;
+ VDDIO-supply = <&mt6359_vio18_ldo_reg>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&touch_pins>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-1 = <&rt1715_int_pins>;
+ clock-frequency = <1000000>;
+ status = "okay";
+};
+
+&i2c5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c5_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&i2c6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c6_pins>;
+ clock-frequency = <400000>;
+ status = "okay";
+};
+
+&mmc0 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc0_default_pins>;
+ pinctrl-1 = <&mmc0_uhs_pins>;
+ bus-width = <8>;
+ max-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ supports-cqe;
+ cap-mmc-hw-reset;
+ no-sdio;
+ no-sd;
+ hs400-ds-delay = <0x1481b>;
+ vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+ vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+ non-removable;
+};
+
+&mmc1 {
+ status = "okay";
+ pinctrl-names = "default", "state_uhs";
+ pinctrl-0 = <&mmc1_default_pins>;
+ pinctrl-1 = <&mmc1_uhs_pins>;
+ bus-width = <4>;
+ max-frequency = <200000000>;
+ cap-sd-highspeed;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ no-mmc;
+ no-sdio;
+ cd-gpios = <&pio 2 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&mt6359_vpa_buck_reg>;
+ vqmmc-supply = <&mt6359_vsim1_ldo_reg>;
+};
+
+&mt6359_vbbck_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcn18_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcn33_2_bt_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vcore_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vpa_buck_reg {
+ regulator-max-microvolt = <3100000>;
+};
+
+&mt6359_vpu_buck_reg {
+ regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359_vsim1_ldo_reg {
+ regulator-enable-ramp-delay = <480>;
+};
+
+&mt6359_vufs_ldo_reg {
+ regulator-always-on;
+};
+
+&mt6359codec {
+ mediatek,mic-type-0 = <1>; /* ACC */
+ mediatek,mic-type-1 = <3>; /* DCC */
+};
+
+&pio {
+ audio_default_pins: audio-default-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO101__FUNC_O_AUD_CLK_MOSI>,
+ <PINMUX_GPIO102__FUNC_O_AUD_SYNC_MOSI>,
+ <PINMUX_GPIO103__FUNC_O_AUD_DAT_MOSI0>,
+ <PINMUX_GPIO104__FUNC_O_AUD_DAT_MOSI1>,
+ <PINMUX_GPIO105__FUNC_I0_AUD_DAT_MISO0>,
+ <PINMUX_GPIO106__FUNC_I0_AUD_DAT_MISO1>,
+ <PINMUX_GPIO107__FUNC_B0_I2SIN_MCK>,
+ <PINMUX_GPIO108__FUNC_B0_I2SIN_BCK>,
+ <PINMUX_GPIO109__FUNC_B0_I2SIN_WS>,
+ <PINMUX_GPIO110__FUNC_I0_I2SIN_D0>,
+ <PINMUX_GPIO114__FUNC_O_I2SO2_MCK>,
+ <PINMUX_GPIO115__FUNC_B0_I2SO2_BCK>,
+ <PINMUX_GPIO116__FUNC_B0_I2SO2_WS>,
+ <PINMUX_GPIO117__FUNC_O_I2SO2_D0>,
+ <PINMUX_GPIO118__FUNC_O_I2SO2_D1>,
+ <PINMUX_GPIO121__FUNC_B0_PCM_CLK>,
+ <PINMUX_GPIO122__FUNC_B0_PCM_SYNC>,
+ <PINMUX_GPIO124__FUNC_I0_PCM_DI>,
+ <PINMUX_GPIO125__FUNC_O_DMIC1_CLK>,
+ <PINMUX_GPIO126__FUNC_I0_DMIC1_DAT>,
+ <PINMUX_GPIO128__FUNC_O_DMIC2_CLK>,
+ <PINMUX_GPIO129__FUNC_I0_DMIC2_DAT>;
+ };
+ };
+
+ dptx_pins: dptx-pins {
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO46__FUNC_I0_DP_TX_HPD>;
+ bias-pull-up;
+ };
+ };
+
+ edp_panel_3v3_en_pins: edp-panel-3v3-en-pins {
+ pins1 {
+ pinmux = <PINMUX_GPIO15__FUNC_B_GPIO15>;
+ output-high;
+ };
+ };
+
+ eth_default_pins: eth-default-pins {
+ pins-cc {
+ pinmux = <PINMUX_GPIO139__FUNC_B0_GBE_TXC>,
+ <PINMUX_GPIO140__FUNC_I0_GBE_RXC>,
+ <PINMUX_GPIO141__FUNC_I0_GBE_RXDV>,
+ <PINMUX_GPIO142__FUNC_O_GBE_TXEN>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+
+ pins-mdio {
+ pinmux = <PINMUX_GPIO143__FUNC_O_GBE_MDC>,
+ <PINMUX_GPIO144__FUNC_B1_GBE_MDIO>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ input-enable;
+ };
+
+ pins-power {
+ pinmux = <PINMUX_GPIO145__FUNC_B_GPIO145>,
+ <PINMUX_GPIO146__FUNC_B_GPIO146>;
+ output-high;
+ };
+
+ pins-rxd {
+ pinmux = <PINMUX_GPIO135__FUNC_I0_GBE_RXD3>,
+ <PINMUX_GPIO136__FUNC_I0_GBE_RXD2>,
+ <PINMUX_GPIO137__FUNC_I0_GBE_RXD1>,
+ <PINMUX_GPIO138__FUNC_I0_GBE_RXD0>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+
+ pins-txd {
+ pinmux = <PINMUX_GPIO131__FUNC_O_GBE_TXD3>,
+ <PINMUX_GPIO132__FUNC_O_GBE_TXD2>,
+ <PINMUX_GPIO133__FUNC_O_GBE_TXD1>,
+ <PINMUX_GPIO134__FUNC_O_GBE_TXD0>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ };
+ };
+
+ eth_sleep_pins: eth-sleep-pins {
+ pins-cc {
+ pinmux = <PINMUX_GPIO139__FUNC_B_GPIO139>,
+ <PINMUX_GPIO140__FUNC_B_GPIO140>,
+ <PINMUX_GPIO141__FUNC_B_GPIO141>,
+ <PINMUX_GPIO142__FUNC_B_GPIO142>;
+ };
+
+ pins-mdio {
+ pinmux = <PINMUX_GPIO143__FUNC_B_GPIO143>,
+ <PINMUX_GPIO144__FUNC_B_GPIO144>;
+ input-disable;
+ bias-disable;
+ };
+
+ pins-rxd {
+ pinmux = <PINMUX_GPIO135__FUNC_B_GPIO135>,
+ <PINMUX_GPIO136__FUNC_B_GPIO136>,
+ <PINMUX_GPIO137__FUNC_B_GPIO137>,
+ <PINMUX_GPIO138__FUNC_B_GPIO138>;
+ };
+
+ pins-txd {
+ pinmux = <PINMUX_GPIO131__FUNC_B_GPIO131>,
+ <PINMUX_GPIO132__FUNC_B_GPIO132>,
+ <PINMUX_GPIO133__FUNC_B_GPIO133>,
+ <PINMUX_GPIO134__FUNC_B_GPIO134>;
+ };
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>,
+ <PINMUX_GPIO55__FUNC_B1_SCL0>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c1_pins: i2c1-pins {
+ pins {
+ pinmux = <PINMUX_GPIO58__FUNC_B1_SDA1>,
+ <PINMUX_GPIO57__FUNC_B1_SCL1>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c2_pins: i2c2-pins {
+ pins {
+ pinmux = <PINMUX_GPIO60__FUNC_B1_SDA2>,
+ <PINMUX_GPIO59__FUNC_B1_SCL2>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c3_pins: i2c3-pins {
+ pins {
+ pinmux = <PINMUX_GPIO62__FUNC_B1_SDA3>,
+ <PINMUX_GPIO61__FUNC_B1_SCL3>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c4_pins: i2c4-pins {
+ pins {
+ pinmux = <PINMUX_GPIO64__FUNC_B1_SDA4>,
+ <PINMUX_GPIO63__FUNC_B1_SCL4>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c5_pins: i2c5-pins {
+ pins {
+ pinmux = <PINMUX_GPIO66__FUNC_B1_SDA5>,
+ <PINMUX_GPIO65__FUNC_B1_SCL5>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ i2c6_pins: i2c6-pins {
+ pins {
+ pinmux = <PINMUX_GPIO68__FUNC_B1_SDA6>,
+ <PINMUX_GPIO67__FUNC_B1_SCL6>;
+ bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+ drive-strength-microamp = <1000>;
+ };
+ };
+
+ gpio_key_pins: gpio-key-pins {
+ pins {
+ pinmux = <PINMUX_GPIO42__FUNC_B1_KPCOL0>,
+ <PINMUX_GPIO43__FUNC_B1_KPCOL1>,
+ <PINMUX_GPIO44__FUNC_B1_KPROW0>;
+ };
+ };
+
+ mmc0_default_pins: mmc0-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO157__FUNC_B1_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO161__FUNC_B1_MSDC0_DAT0>,
+ <PINMUX_GPIO160__FUNC_B1_MSDC0_DAT1>,
+ <PINMUX_GPIO159__FUNC_B1_MSDC0_DAT2>,
+ <PINMUX_GPIO158__FUNC_B1_MSDC0_DAT3>,
+ <PINMUX_GPIO154__FUNC_B1_MSDC0_DAT4>,
+ <PINMUX_GPIO153__FUNC_B1_MSDC0_DAT5>,
+ <PINMUX_GPIO152__FUNC_B1_MSDC0_DAT6>,
+ <PINMUX_GPIO151__FUNC_B1_MSDC0_DAT7>,
+ <PINMUX_GPIO156__FUNC_B1_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO155__FUNC_O_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc0_uhs_pins: mmc0-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO157__FUNC_B1_MSDC0_CLK>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO161__FUNC_B1_MSDC0_DAT0>,
+ <PINMUX_GPIO160__FUNC_B1_MSDC0_DAT1>,
+ <PINMUX_GPIO159__FUNC_B1_MSDC0_DAT2>,
+ <PINMUX_GPIO158__FUNC_B1_MSDC0_DAT3>,
+ <PINMUX_GPIO154__FUNC_B1_MSDC0_DAT4>,
+ <PINMUX_GPIO153__FUNC_B1_MSDC0_DAT5>,
+ <PINMUX_GPIO152__FUNC_B1_MSDC0_DAT6>,
+ <PINMUX_GPIO151__FUNC_B1_MSDC0_DAT7>,
+ <PINMUX_GPIO156__FUNC_B1_MSDC0_CMD>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-ds {
+ pinmux = <PINMUX_GPIO162__FUNC_B0_MSDC0_DSL>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO155__FUNC_O_MSDC0_RSTB>;
+ drive-strength = <MTK_DRIVE_8mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc1_default_pins: mmc1-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO164__FUNC_B1_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO163__FUNC_B1_MSDC1_CMD>,
+ <PINMUX_GPIO165__FUNC_B1_MSDC1_DAT0>,
+ <PINMUX_GPIO166__FUNC_B1_MSDC1_DAT1>,
+ <PINMUX_GPIO167__FUNC_B1_MSDC1_DAT2>,
+ <PINMUX_GPIO168__FUNC_B1_MSDC1_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-insert {
+ pinmux = <PINMUX_GPIO2__FUNC_B_GPIO2>;
+ bias-pull-up;
+ };
+ };
+
+ mmc1_uhs_pins: mmc1-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO164__FUNC_B1_MSDC1_CLK>;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO163__FUNC_B1_MSDC1_CMD>,
+ <PINMUX_GPIO165__FUNC_B1_MSDC1_DAT0>,
+ <PINMUX_GPIO166__FUNC_B1_MSDC1_DAT1>,
+ <PINMUX_GPIO167__FUNC_B1_MSDC1_DAT2>,
+ <PINMUX_GPIO168__FUNC_B1_MSDC1_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc2_default_pins: mmc2-default-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO170__FUNC_B1_MSDC2_CLK>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO169__FUNC_B1_MSDC2_CMD>,
+ <PINMUX_GPIO171__FUNC_B1_MSDC2_DAT0>,
+ <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>,
+ <PINMUX_GPIO173__FUNC_B1_MSDC2_DAT2>,
+ <PINMUX_GPIO174__FUNC_B1_MSDC2_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+
+ pins-pcm {
+ pinmux = <PINMUX_GPIO123__FUNC_O_PCM_DO>;
+ };
+ };
+
+ mmc2_uhs_pins: mmc2-uhs-pins {
+ pins-clk {
+ pinmux = <PINMUX_GPIO170__FUNC_B1_MSDC2_CLK>;
+ drive-strength = <MTK_DRIVE_4mA>;
+ bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+ };
+
+ pins-cmd-dat {
+ pinmux = <PINMUX_GPIO169__FUNC_B1_MSDC2_CMD>,
+ <PINMUX_GPIO171__FUNC_B1_MSDC2_DAT0>,
+ <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>,
+ <PINMUX_GPIO173__FUNC_B1_MSDC2_DAT2>,
+ <PINMUX_GPIO174__FUNC_B1_MSDC2_DAT3>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc2_eint_pins: mmc2-eint-pins {
+ pins-dat1 {
+ pinmux = <PINMUX_GPIO172__FUNC_B_GPIO172>;
+ input-enable;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ mmc2_dat1_pins: mmc2-dat1-pins {
+ pins-dat1 {
+ pinmux = <PINMUX_GPIO172__FUNC_B1_MSDC2_DAT1>;
+ input-enable;
+ drive-strength = <MTK_DRIVE_6mA>;
+ bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+ };
+ };
+
+ panel_default_pins: panel-default-pins {
+ pins-dcdc {
+ pinmux = <PINMUX_GPIO45__FUNC_B_GPIO45>;
+ output-low;
+ };
+
+ pins-en {
+ pinmux = <PINMUX_GPIO111__FUNC_B_GPIO111>;
+ output-low;
+ };
+
+ pins-rst {
+ pinmux = <PINMUX_GPIO25__FUNC_B_GPIO25>;
+ output-high;
+ };
+ };
+
+ rt1715_int_pins: rt1715-int-pins {
+ pins_cmd0_dat {
+ pinmux = <PINMUX_GPIO12__FUNC_B_GPIO12>;
+ bias-pull-up;
+ input-enable;
+ };
+ };
+
+ spi0_pins: spi0-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO69__FUNC_O_SPIM0_CSB>,
+ <PINMUX_GPIO70__FUNC_O_SPIM0_CLK>,
+ <PINMUX_GPIO71__FUNC_B0_SPIM0_MOSI>,
+ <PINMUX_GPIO72__FUNC_B0_SPIM0_MISO>;
+ bias-disable;
+ };
+ };
+
+ spi1_pins: spi1-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO75__FUNC_O_SPIM1_CSB>,
+ <PINMUX_GPIO76__FUNC_O_SPIM1_CLK>,
+ <PINMUX_GPIO77__FUNC_B0_SPIM1_MOSI>,
+ <PINMUX_GPIO78__FUNC_B0_SPIM1_MISO>;
+ bias-disable;
+ };
+ };
+
+ spi2_pins: spi2-pins {
+ pins-spi {
+ pinmux = <PINMUX_GPIO79__FUNC_O_SPIM2_CSB>,
+ <PINMUX_GPIO80__FUNC_O_SPIM2_CLK>,
+ <PINMUX_GPIO81__FUNC_B0_SPIM2_MOSI>,
+ <PINMUX_GPIO82__FUNC_B0_SPIM2_MISO>;
+ bias-disable;
+ };
+ };
+
+ touch_pins: touch-pins {
+ pins-irq {
+ pinmux = <PINMUX_GPIO6__FUNC_B_GPIO6>;
+ input-enable;
+ bias-disable;
+ };
+
+ pins-reset {
+ pinmux = <PINMUX_GPIO5__FUNC_B_GPIO5>;
+ output-high;
+ };
+ };
+
+ uart0_pins: uart0-pins {
+ pins {
+ pinmux = <PINMUX_GPIO31__FUNC_O_UTXD0>,
+ <PINMUX_GPIO32__FUNC_I1_URXD0>;
+ bias-pull-up;
+ };
+ };
+
+ uart1_pins: uart1-pins {
+ pins {
+ pinmux = <PINMUX_GPIO33__FUNC_O_UTXD1>,
+ <PINMUX_GPIO34__FUNC_I1_URXD1>;
+ bias-pull-up;
+ };
+ };
+
+ uart2_pins: uart2-pins {
+ pins {
+ pinmux = <PINMUX_GPIO35__FUNC_O_UTXD2>,
+ <PINMUX_GPIO36__FUNC_I1_URXD2>;
+ bias-pull-up;
+ };
+ };
+
+ usb_default_pins: usb-default-pins {
+ pins-iddig {
+ pinmux = <PINMUX_GPIO83__FUNC_B_GPIO83>;
+ input-enable;
+ bias-pull-up;
+ };
+
+ pins-valid {
+ pinmux = <PINMUX_GPIO85__FUNC_I0_VBUSVALID>;
+ input-enable;
+ };
+
+ pins-vbus {
+ pinmux = <PINMUX_GPIO84__FUNC_O_USB_DRVVBUS>;
+ output-high;
+ };
+
+ };
+
+ usb1_default_pins: usb1-default-pins {
+ pins-valid {
+ pinmux = <PINMUX_GPIO88__FUNC_I0_VBUSVALID_1P>;
+ input-enable;
+ };
+
+ pins-usb-hub-3v3-en {
+ pinmux = <PINMUX_GPIO112__FUNC_B_GPIO112>;
+ output-high;
+ };
+ };
+
+ wifi_pwrseq_pins: wifi-pwrseq-pins {
+ pins-wifi-enable {
+ pinmux = <PINMUX_GPIO127__FUNC_B_GPIO127>;
+ output-low;
+ };
+ };
+};
+
+&pmic {
+ interrupt-parent = <&pio>;
+ interrupts = <222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&scp {
+ memory-region = <&scp_mem>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-0 = <&uart1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&spi2 {
+ pinctrl-0 = <&spi2_pins>;
+ pinctrl-names = "default";
+ mediatek,pad-select = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+};
+
+&u3phy0 {
+ status = "okay";
+};
+
+&u3phy1 {
+ status = "okay";
+};
+
+&u3phy2 {
+ status = "okay";
+};
+
+&xhci0 {
+ status = "okay";
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+};
+
+&xhci1 {
+ status = "okay";
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+ vbus-supply = <&usb_hub_reset_1v8>;
+};
+
+&xhci2 {
+ status = "okay";
+ vusb33-supply = <&mt6359_vusb_ldo_reg>;
+};
--
2.18.0
More information about the Linux-mediatek
mailing list